• Journal of information and communication convergence engineering
• /
• 제18권3호
• /
• pp.183-187
• /
• 2020

The general Wi-Fi network connection structure is that a number of IoT (Internet of Things) sensor nodes are directly connected to one AP (Access Point) node. In this structure, the range of the network that can be established within the specified specifications such as the range of signal strength (RSSI) to which the AP node can connect and the maximum connection capacity is limited. To overcome these limitations, multiple middleware bridge technologies for dynamic scalability and load balancing were studied. However, these network expansion technologies have difficulties in terms of the rules and conditions of AP nodes installed during the initial network deployment phase In this paper, an intelligent edge computing IoT device is developed for constructing an intelligent autonomous cluster edge computing network and applying it to real-time road danger context aware and notification system through an intelligent risk situation recognition algorithm.

• 전기학회논문지
• /
• 제65권1호
• /
• pp.103-107
• /
• 2016

In general, the voltage stability of induction generator is lower than synchronous generator. Induction generator has a number of advantages over the synchronous generator on the side of price and maintenance. So Induction generator has been applied to the small hydroelectric power of low output. Induction generator usually generates a high current during grid connection. The high current that occurs during grid connection can cause a voltage drop in the system. In order to increase the supply of the induction generator, it is necessary to propose a method of reducing high current. This paper proposes some method of the soft start to reduce voltage drop caused by the large starting current. soft-start method has high voltage drop effect than direct start method, control of firing angle can be increased the voltage drop effect.

• 논리연구
• /
• 제12권2호
• /
• pp.1-29
• /
• 2009

유명론자인 필드에 따르면, 수학적 대상은 존재하지 않지만 존재할 수도 있었다. 이 글의 목적은 이런 필드의 '우연적' 유명론이 설득력이 있는지를 살펴보는 데 있다. 이를 위해 나는 여기서 필드와 플라톤주의자인 헤일과 라이트 사이에 벌어진 논쟁을 분석하고 평가한다. 나는 설명의 요구 논증은 여전히 유효하지만, 거기서 사용된 일반 원리를 뒷받침해줄 별도의 논증이 필요하다고 주장하며, 반절연 원리에 근거한 비판의 경우 그 원리 자체에 이미 각 진영의 철학적 입장이 전제되어 있다고 주장한다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1999년도 가을 학술발표회 논문집
• /
• pp.403-410
• /
• 1999

General1y, H-section is used for columns and beams in the middle and low steel building, But it has a strong and weak axis. Thus if H-section is used for columns, the structure needs reinforcement on the weak axis. Therefore recently, square holler section(S.H.S) is used for columns because it is able to coiler the vulnerability of H-section. Structural analysis is usually executed under the assumption that connections are either ideally pinned joint or fully rigid joint. Actually all connections are semi-rigid which possess a rotational stiffness. Therefore it can be designed economically as using the property of connections which has a rotational stiffness. This paper presents a prediction model curve which is fitted Kishi-Chen power Model about the behavior of connection between H-beam and S.H.S column. Non-linear analysis program was considered the non-linearity of semi-rigid connection and the geometrical non-linearity under the effect of axial force. It was programed by FORTRAN90 and Visual Basic.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1997년도 봄 학술발표회 논문집
• /
• pp.211-218
• /
• 1997

Analysis of structures are usually executed under the assumption that connections are either ideally pinned joint or fully rigid joint. But in general all structures is connected under the semi-rigid connections. Semi-rigid connect ions have demerits that is simplification work on connection's behavior, moment-rotation relationships of connect ions , apprehension of nonlinear analysis etc. On the other hand there is merits that is improvements of serviceability, economic efficiency, construction in predicting real behavior frames. This study is to make model of connect ions by based on experimental study and after analysis on frames considering characteristics of semi-rigid connections. semi-rigid connection's influence on the behavior of structures and fundamental data on application of structures that is connected between S H S column and H beam is exhibited.

• Steel and Composite Structures
• /
• 제3권3호
• /
• pp.169-184
• /
• 2003

This paper presents a generic modelling of composite steel-concrete beams with elastic shear connection. It builds on the well-known seminal technique of Newmark, Siess and Viest, in order to formulate the partial interaction formulation for solution under a variety of end conditions, and lends itself well for modification to enable direct quantification of effects such as shrinkage, creep, and limited shear connection slip capacity. This application is possible because the governing differential equations are set up and solved in a fashion whereby inclusion of the kinematic and static end conditions merely requires a statement of the appropriate constants of integration that are generated in the solution of the linear differential equations. The method is applied in the paper for the solution of the well-studied behaviour of simply supported beams with partial interaction, as well as to provide solutions for a beam encastr$\acute{e}$ at its ends, and for a propped cantilever.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.558-564
• /
• 2006

When vehicles pass the connection between the bridge and earthwork, the difference of both sections' stiffness produces an increasing wheelload. As a consequence, it results in the excessive vibration of vehicles and the damage of bearing system. In general, steel plate girder railway bridges without ballast track have larger stiffness than the bridge with ballast, and produces larger impulse on the bridge superstructure. Thus, it is necessary to reduce the differences of both stiffness. This study presents parametric studies on the behavior of plate girder bridges and their tracks by means of various stiffnesses and the length of approach zone. The results of numerical study showed that the smaller the stiffness of both sides and the longer the length of approach zone, the variation of wheelload becomes smaller. Hence, it gives less burden into the plate girder bridges and their tracks. It is expected that the results of parametric study can be used as a preliminary data for the determination of economical length on the approach zone and the stiffness of both sides.

• 한국구조물진단유지관리공학회 논문집
• /
• 제5권4호
• /
• pp.177-184
• /
• 2001

In this study, three most distinct types of general rigid connections are included in the modelling, with is implemented into a computer code. The cost, functions of connections are constructed by using the estimated unit cost of bolting, welding and connection-steel elements incorporating all the effect of materials, labor, and fabrication work. Bused on the recent developments of the reliability-based structural analysis and design as well as the extending knowledge on the probabilistic characteristics of load and resistances, the probability based design criteria have been successfully developed for many standards. Since the probabilistic characteristics depend highly on the local load and resistances, it is recognized to develop the design criterion compatible with domestic requirements. The existing optimum design methods, which are generally based on the structural theory and certain engineering experience, do not realistically consider the uncertainties of load and resistances and the basic reliability concepts.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.469-472
• /
• 2008

In general, structures in service gradually lose original performance according to time due to initial defects in design and construction, or exposure to unfavorable external conditions such as repeated loading or deteriorating environment, and in extreme cases, may collapse in large disaster. Therefore, in order to maintain the serviceability of structures at optimal level, advanced structure measuring system which can inform optimal time point and method of maintenance is required in addition to accurate prediction of residual life the structure by periodic inspection. To guarantee the safety level of bridge structure and to prevent from disaster, the integration of safety network for bridge structures are needed. Therefore in this study, to enhance the effectiveness of safety network for bridge, the connection methodologies between safety network and pre-installed bridge monitoring system are investigated.

• 한국건설순환자원학회논문집
• /
• 제6권1호
• /
• pp.66-71
• /
• 2018

일반적으로 소구경 말뚝을 이용한 기존교각의 확대보강을 시행하는 경우 접합부의 일체성을 유지하기 위해 후 설치 앵커 중에서 이형철근을 사용한 부착식 앵커를 사용한다. 그러나 부착식 앵커의 경우 접합재의 종류 등에 따라 성능이 크게 좌우됨에도 불구하고 기계식 앵커와는 달리 설계방법의 표준화와 함께 적절한 성능평가를 위한 표준적인 실험방법도 제시되지 않고 있는 실정이다. 이에 따라 본 연구에서는 철근의 겹이음 및 앵커철근을 이용한 모형실험을 실시하여 부착식 앵커의 성능에 대한 평가를 수행하였다. 실험 결과, 접합하지 않은 시험체의 구조 성능이 가장 우수하게 나타났으며, 파괴양상은 펀칭전단 파괴로 나타났다. 연결되지 않은 부재가 연결된 부재보다는 부재 끝단의 처짐이 더 작게 발생되며, 큰 크기로 연결된 부재의 처짐이 작게 연결된 부재의 처짐보다는 크게 나타나, 하중이 증가할수록 앵커 철근 또는 겹이음 철근의 미끌림 등의 현상이 발생될 가능성이 큰 것으로 나타났다.