• 한국수소및신에너지학회논문집
• /
• 제12권3호
• /
• pp.169-176
• /
• 2001

The purpose of study is to obtain low-emission and high-efficiency in LPG engine with hydrogen enrichment. The test engine was named heavy-duty variable compression ratio single cylinder engine (VCSCE). The fuel supply system provides LPG/hydrogen mixtures based on same heating value. Various sensors such as crank shaft position sensor (CPS) and hall sensor supply spark timing data to ignition controller. Displacement of VCSCE is $1858.2cm^3$. VCSCE was runned 1400rpm with compression ratio 8. Spark timing was set MBT without knocking. Relative air-fuel ratio(${\lambda}$) of this work was varied between 0.76 and 1.5. As a result, i) Maximum thermal efficiency occurred at ${\lambda}$ value 1.0. It was shown that thermal efficiency was increased approximately 5% with hydrogen enrichment at same ${\lambda}$ value. ii) Engine-out carbon monoxide (CO) emissions were decreased at a great rate under LPG/hydrogen mixture fuelling. iii) Total hydrocarbon (THC) emission was much exhausted in rich zone, same as CO. But THC was exhausted a little bit more in lean zone. iv) Finally, engine-out oxides of nitrogen (NOx) was increased with ${\lambda}$ value 1.0 zone at a greater rate with hydrogen enrichment due to high adiabatic flame temperature.

• Korean Chemical Engineering Research
• /
• 제53권2호
• /
• pp.193-198
• /
• 2015

Polycaprolactone, Dichloromethane, 이산화탄소로 구성된 3성분계 고압 시스템의 상거동 측정 실험은 가변 부피 셀 장치를 이용해서 측정했다. 실험의 온도범위는 313.15 K에서 353.15 K, 압력은 약 300 bar까지 측정했으며 실험결과는 Polycaprolactone의 질량 분율이 1.0%, 2.0%, 3.0%일 때 온도와 이산화탄소/Dichloromethane의 질량 분율로 정리했다. 또한 실험 결과는 hybrid 상태방정식 (Peng-Robinson 상태방정식과 SAFT 상태방정식의 혼합형태) 을 이용하여 열역학적으로 검증하였으며, 혼합규칙은 반데르 발스의 단일 유체 혼합규칙을 사용했다. 이 다성분계 시스템에서 이원 상호 작용 파라미터 등, 각종 파라미터는 심플렉스 알고리즘을 통해 최적화했다.

• Korean Chemical Engineering Research
• /
• 제58권1호
• /
• pp.163-169
• /
• 2020

Synthesis of Fe-Co/meso-HZSM5 catalyst, intended to be applied in Fischer-Tropsch (FT) reaction was investigated. The study emphasized the effect of desilication agents, NaOH and KOH, on the catalyst materials properties. Impregnation composition of active metal (Fe and Co) was also examined. HZSM-5, converted from ammonium ZSM-5 through calcination, was treated with NaOH and KOH for desilication, followed by impregnation with 10% metal loading. Fe composition in the initial mixture was varied at 10-50% from total composition. After impregnation, reduction was applied by flowing hydrogen gas at 400 ℃ for 10 hours. The use of KOH solution induced greater mesoporous volumes; however, it had a detrimental effect on zeolite crystal structure. NaOH solutions, on the other hand, increased mesopore area as high as 100%, indicated from surface area increase from 266.28 m²/g of HZSM-5, to 526.03 m²/g of NaOH-desilicated HZSM-5. In addition, the application of NaOH solution increased pore volume from 0.14 cc/g to 0.486 cc/g. Further, more Fe-Co alloys and less oxide of iron (Fe₂O₃) as well cobalt (Co₃O₄) had been commonly observed in the produced catalysts. The largest Fe-Co alloys could be found in 50Fe-50Co/HZSM-5

• 한국세라믹학회지
• /
• 제42권4호
• /
• pp.232-236
• /
• 2005

$LiNbO_{3}$ optical waveguide 구조를 neutral loop discharge plasma 방법으로 식각시 As과 $C\_{3}F_{8}$가 혼합된 가스 유량에 따른 식각속도와 표면조도 값의 특성을 관찰하였다. 식각 후 식각속도와 식각단면은 scanning electron microscopy로 비교 분석하였으며, 표면조도는 atomic force microscopy로 측정하였다. Ar과 $C_{3}F_{8}$가 혼합된 가스 유량비를 각각 0.1-0.5로 증가시킴에 따라 식각속도와 표면조도는 0.2에서 가장 높게 나타났으며, bias power를 증가함에 따라 300W에서 가장 우수한 식각속도와 가장 평탄한 표면 형상을 얻을 수 있었다.

• 전기화학회지
• /
• 제8권1호
• /
• pp.24-31
• /
• 2005

Ion-Shower-Doping장비 및 $PH_/3M_2$혼합 가스를 사용하여 Phosphorous를 ELA방법으로 제조된 Poly-Si에 가속 전압 및 조사량을 변수로 이온 주입하였다. As-implanted된 시편의 결정도는 UV-transmittance spectroscopy를 사용하여 측정하였다. 이 때 UV-transmittance를 이용하여 측정한 값은 Raman spectroscopy를 이용해서 측정한 값과 서로 관련되어 있음을 알았다. 면 저항은 가속전압이 1kV에서 15kV까지 증가함에 따라 감소한다 그러나 가혹한 도핑조건하에서는 가속전압의 증가 시 면 저항이 증가한다. 이는 활성화 열처리 후 치유되지 않은 결함에 의해 전자가 포획되며 이에 따라 전하 운반자의 농도가 감소하는 때문이다. 활성화 열처리는 로열처리, RTA 열처리, ELA 열처리 등의 방법으로 수행하였고 열처리 방법에 따르는 도펀트의 활성화 및 결함의 회복의 거동을 연구하였다

• 한국전기전자재료학회논문지
• /
• 제29권8호
• /
• pp.510-515
• /
• 2016

Single-chamber solid oxide fuel cells (SC-SOFCs) consist of only one gas chamber, in which both the anode and the cathode are exposed to the same fuel-oxidant mixture. Thus, this configuration shows good thermal and mechanical resistance and allows rapid start-up and -down. In this study, the unit cell consisting of $La_{0.8}Sr_{0.2}MnO_3$ (cathode) / $Zr_{0.84}Y_{0.16}O_{2-x}$ (electrolyte) / $Ni-Zr_{0.84}Y_{0.16}O_{2-x}$ (anode) was fabricated and its electrochemical property was investigated as a function of temperature and the volume ratio of fuel and oxidant for SC-SOFCs. Impedance spectra were also investigated in order to figure out the electrical characteristics of the cell. As a result, the cell performance was governed by the polarization resistances of the electrodes. The cell exhibited an acceptable cell-performance of $86mW/cm^2$ at $800^{\circ}C$ and stable performance for 3 hs under 0.7 V.

• 한국재료학회지
• /
• 제28권5호
• /
• pp.301-307
• /
• 2018

A boron-doped diamond(BDD) electrode is attractive for many electrochemical applications due to its distinctive properties: an extremely wide potential window in aqueous and non-aqueous electrolytes, a very low and stable background current and a high resistance to surface fouling. An Ar gas mixture of $H_2$, $CH_4$ and trimethylboron (TMB, 0.1 % $C_3H_9B$ in $H_2$) is used in a hot filament chemical vapor deposition(HFCVD) reactor. The effect of argon addition on quality, structure and electrochemical property is investigated by scanning electron microscope(SEM), X-ray diffraction(XRD) and cyclic voltammetry(CV). In this study, BDD electrodes are manufactured using different $Ar/CH_4$ ratios ($Ar/CH_4$ = 0, 1, 2 and 4). The results of this study show that the diamond grain size decreases with increasing $Ar/CH_4$ ratios. On the other hand, the samples with an $Ar/CH_4$ ratio above 5 fail to produce a BDD electrode. In addition, the BDD electrodes manufactured by introducing different $Ar/CH_4$ ratios result in the most inclined to (111) preferential growth when the $Ar/CH_4$ ratio is 2. It is also noted that the electrochemical properties of the BDD electrode improve with the process of adding argon.

• 보존과학연구
• /
• 통권14호
• /
• pp.94-108
• /
• 1993

The cultural properties of cloth are of animal orgin (silk), or of vegetable orgin(cotton, hemp, ramie). As clothes are of an orginic material, they were subjected to damage by chemical, phisigical or biological factors, viz, moulds insects, lights, humidity and temperature changes, etc. And these factors promote that clothes generally result from various types of deterioration. In 1992, We were performed the conservation treatments for total 9 pieces of cloth, such as 3 pieces of General PAK SHIN-RYONG(Important Folklore Material No.110) 3 pieces of Madam Jung(Important Folklore Material No.115) and 1 piece of King Se-jo(Important Folklore Material No.219). The procedure of the conservation treatment for clothes describe the following below. 1) The washing and dry-cleaning to remove the contaminated substances from cloth was used 0.2% stearyl potassium soap solution and the mixture solution compound of n-Hexane, C6H14. and n-Decane, C10H22. And after the washing and dry-cleaning, the dry of clothes was carried out in a warm condition. These steps were repeated in 2 times over for each cloth. 2) The repair of clothes was attached the similar textiles to stronger fabric linings by needlework.3) The reprodution was made for cloth of King Se-jo to equalize the type, color, quality and skill of materials. 4) After these above procedures, all clothes fumigated to prevent the biodeterioration by using the mixed gas of methyl bromide and ethylene oxide as insecticide and fungicide. 5) Finally for the purpose to keep in a safety long-term condition, the treated clothes sealed with Biaxially Oriented Polyvinylacohol Film(BO-PVA film) and Helium, purity 99.999%, filled up in sealed BO-PVA film bag.

• Nuclear Engineering and Technology
• /
• 제23권4호
• /
• pp.438-443
• /
• 1991

각확산도가 작은 $He^+$ 이온빔 인출전류를 최대로 얻기 위하여 Duoplasmatron 이온원의 동작특성을 조사하였다. 이온원의 기체압력, 아크전류. 전자석 전류, 인출전압등을 변화시키면서 인출되는 $He^+$ 이온빔 전류의 변화를 관찰하였다. 열음극으로는 Ni망위에 BaO와 SrO의 혼합물을 코팅한 산화물 필라멘트를 사용하였으며, 그것의 평균수명은 약 100시간이었다. 인출전류는 아크전류에 선형적으로 비례했다 이온원 전자석전류를 증가시킴에 따라 인출전류는 증가하였지만 빔의 각확산도가 커졌다. 최대의 인출전류는 0.084 Torr의 이온원 압력에서 얻어졌다. 인출전류는 이론에서와 마찬가지로 인출전압의 3/2승에 비례하였다. 5.72 kV의 인출전압에서는 최적인출조건하에서 50 $\mu$A의 인출전류가 얻어졌다.

• 청정기술
• /
• 제13권1호
• /
• pp.72-78
• /
• 2007

석유 잔사유(PGO)에 포함된 유효성분을 분리하기 위한 기초 연구로 컬럼 및 봉형 용융 결정화기를 사용하여 나프탈렌에 불순물로 2-메틸나프탈렌, 인덴, 1-메틸나프탈렌을 각각 포함시킨 혼합물에 관한 분리정제 연구를 수행하였다. 결정화시, 나프탈렌의 순도는 냉각속도가 낮거나, 융점이 상대적으로 낮은 불순물이 포함될 수 록 증가하는 경향을 나타내었으며, 동일한 조건에서 컬럼형 결정화기의 순도는 봉형에 비해 결정화후 부분용융에서 순도의 증가에 기인하여 높은 경향을 나타내었다.