• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.1
• /
• pp.117-122
• /
• 2006

A CMOS LNA based on a single-stage cascode configuration is designed for MB-OFDM ultra-wide band(UWB) systems. Wideband($3.1GHz\~4.9GHz$) input matching is performed using a simple bandpass filter to minimize the chip size and the noise figure degradation. The simulation results using $0.18{\mu}m$ CMOS process parameters show a power gain of 9.7dB, a 3dB band width of $2.1GHz\~7.1GHz$, a minimum NF of 2dB, an IIP3 of -2dBm. better than -11.8dB of input matching while occupying only $0.74mm^2$ of chip area. It consumes 25.8mW from a 1.8V supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.11
• /
• pp.1081-1090
• /
• 2013

In this paper, a C-band 10 W power amplifier with internally matched input and output matching circuit is designed and fabricated. The used power transistor for the power amplifier is GaAs pHEMT bare-chip. The wire bonding analysis considering the size of the capacitor and the position of transistor pad improves the accurate design. The matching circuit design with the package effect using EM simulation is performed. To reduce the unsymmetry of IMD3 in 2-tone measurement due to the memory effect, the bias circuit minimizing the memory effect is proposed and employed. The measured $P_{1dB}$, power gain, and power added efficiency are 39.8~40.4 dBm, 9.7~10.4 dB, and 33.4~38.0 %, respectively. Adopting the proposed bias circuit, the difference between the upper and lower IMD3 is less than 0.76 dB.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.77-84
• /
• 2007

In this parer, a wideband low-noise amplifier (LNA) has been realized in a 0.18mm CMOS technology for the applications of subsampling direct-conversion RF receivers. By exploiting the inverter-type transimpedance input stage with a 3rd-order Chebyshev matching network, the wideband LNA demonstrates the measured results of the -3dB bandwidth of 5.35GHz, the power gain (S21) of $12\sim18dB$, the noise figure (NF) of $6.9\sim10.8dB$, and the broadband input/output impedance matching of less than -10dB/-24dB within the bandwidth, respectively. The chip dissipates 32.4mW from a single 1.8V supply, and occupies the area of $0.56\times1.0mm^2$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.2
• /
• pp.85-89
• /
• 2011

In this paper, a novel Class-E power amplifier using metamaterials has been realized with one RF LDMOS diffusion metal-oxide-semiconductor field effect transistor. The CRLH structure can lead to metamaterial transmission line with the Class-E power amplifier tuning capability. The CRLH TL is achieved by the frequency offset and the nonlinear phase slope of the CRLH TL for the matching network of the power amplifier. Also, the proposed power amplifier has been realized by using the CRLH structure in the output matching network for better efficiency. Operating frequencies are chosen at 13.56 MHz in this work. The measured results show that the output power of 39.83 dBm and the gain of 11.83dB was obtained. At this point, we have obtained the power-added efficiency (PAE) of 73 % at operation frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.6 s.109
• /
• pp.597-604
• /
• 2006

An ultrawideband(UWB) $3.1{\sim}5.15$ GHz low-noise amplifier employing a novel input matching circuit and feedback topology are presented. The proposed UWB amplifier is Implemented in $0.18{\mu}m$ RF CMOS technology. Measurements show a NF of $3.4{\sim}3.9$ dB, a power gain of $12.8{\sim}14$ dB, better than -9.4 of input matching and, an input IP3 of -1 dBm, while comsuming only 14.5 mW of power.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.10
• /
• pp.3917-3922
• /
• 2010

In this paper, 3 stage amplifier MMIC was designed and fabricated with U-band optimized epitaxal pHEMT that produced by large signal characterization and modeling for 60 GHz band. The pHEMT used in this paper, the gate $0.12\;{\mu}m$ length and total gate width of $100\;{\mu}m$, $200\;{\mu}m$ has been modeled using the large signal designed with negative feedback and MCLF instead of MIM capacitor for improving stability. Fabricated MMIC $2.5{\times}1.5mm^2$ size, current about 40 mA, operating frequency 59.5~60.5 GHz, gain 19.9~18.6 dB, input matching characteristics -14.6~-14.7 dB, output matching characteristics -11.9~-16.3 dB and output -5 dBm characteristics were obtained.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.7
• /
• pp.1537-1543
• /
• 2010

This paper describes a compact microstrip antenna with dual polarization characteristics. The antenna, receiving both a left-hand circularly polarized(LHCP) wave and a right-hand circularly polarized(RHCP) wave, can be used for a polarization diversity. A diamond-shaped patch with internal empty room is designed for impedance matching as well as size reduction. And slots are added around feeding point to improve input matching. The proposed antenna has been applied to GPS(global positioning system), operating at 1.57GHz. And, the proposed idea has been verified and estimated by simulation. The measurement results show that it has VSWR 2:1 bandwidth of 83MHz, 3dB axial bandwidth of about 58MHz, 3dB beamwidth of 90degree, and gain of 0dBi, respectively, for RHCP. Also, it has similar performances for LHCP.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.6
• /
• pp.683-690
• /
• 2015

In Rough set, attribute missing values have several problems such as reduct and core estimation. Further, they do not give some discernable pattern for decision tree construction. Now, there are several methods such as substitutions of typical attribute values, assignment of every possible value, event covering, C4.5 and special LEMS algorithm. However, they are mainly substitutions into frequently appearing values or common attribute ones. Thus, decision rules with high information loss are derived in case that important attribute values are missing in pattern matching. In particular, there is difficult to implement cross validation of the decision rules. In this paper we suggest new method for substituting the missing attribute values into high information gain by using entropy variation among given attributes, and thereby completing the information table. The suggested method is validated by conducting the same rough set analysis on the incomplete information system using the software ROSE.

• Journal of IKEEE
• /
• v.2 no.1 s.2
• /
• pp.15-23
• /
• 1998

In this paper, distributed mixer is studied at microwave frequency. The circuit of distributed mixer composed of gate 1,2, drain transmission lines, matching circuits in input and output terminal, DGFET's. For impedance matching of input and output port at higher frequency, image impedance concept is introduced. In distributed mixer, a DGFET's impedances are absorbed by artificial transmission line, this type of mixer can get a very broadband characteristics compared to that of current systems. A RF/LO signal is applied to each gate input port, and are excited the drain transmission line through transcondutance of the DGFET's. The output signals from each drain port of DGFET's added in same phases. We designed and frabricated the distributed mixer, and a conversion gain, noise figure, bandwidth, LO/RF isolation of the mixer are shown through computer simulation and experimentation.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.3
• /
• pp.10-14
• /
• 2017

A reverberation chamber is widely used in mobile handset measurements due to its faster and simpler measurement process compared to traditional anechoic chambers. We propose an ultra-wideband inverse conical antenna design suitable as a reference antenna in a reverberation chamber. Traditionally, multiple discone antennas are needed to cover more than 10:1 operation bandwidth of a reverberation chamber. The proposed inverse conical antenna offers wideband impedance matching bandwidth by virtue of the linear impedance transition along its oblique side. The antenna is feasible to mount on the conductive walls which can be utilized as a ground to improve the matching bandwidth, antenna gain and radiation patterns. The antenna geometry is optimized using a 3D electromagnetic simulation tool and fabricated using a 3D printer. The measured results show that the antenna reflection coefficient lower than -10dB and radiation efficiency more than 70% at the frequency range of 0.65~7 GHz.