• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.269-274
• /
• 2011

A CFD analysis was performed to examine the inner channel blockage of dual-cooled fuel which has being developed for the power uprate of a pressurized water reactor (PWR). The dual-cooled fuel consists of an annular fuel pellet($UO_2$) and dual claddings as well as internal and external cooling channels. The dual-cooled annular fuel is different from a conventional solid 려el by employing an internal cooling channel for each fuel pellet as well as an external cooling channel. One of the key issues is the hypothetical event of inner channel blockage because the inner channel is an isolated flow channel without the coolant mixing between the neighboring flow channels. The inner channel blockage could cause the Departure from Nucleate Boiling (DNB) in the inner channel that eventually causes a fuel failure. This paper presents the CFD simulation of the flow through the side holes of the bottom end plug for the complete entrance blockage of the inner channel. Since the amount of coolant supply to the inner channel depends on largely the pressure loss at the side hole, the pressure loss coefficient of the side hole was estimated by the CFD analysis. The CFD prediction of the loss coefficient showed a reasonable agreement with an experimental data for the complete blockage of both the inner channel entrance and the outer channel. The CFD predictions also showed the decrease of the loss coefficient as the outer channel blockage increases.

• 한국수소및신에너지학회논문집
• /
• 제30권6호
• /
• pp.593-600
• /
• 2019

The combustion characteristics of methane/hydrogen pre-mixed flame have been investigated with swirl stabilized flame in a laboratory-scale pre-mixed combustor with constant heat load of 5.81 kW. Hydrogen/methane fuel and air were mixed in a pre-mixer and introduced to the combustor through a burner nozzle with different degrees of swirl angle. The effects of hydrogen addition and swirl intensity on the combustion characteristics of pre-mixed methane flames were examined using particle image velocimetry (PIV), micro-thermocouples, various optical interference filters and gas analyzers to provide information about flow velocity, temperature distributions, and species concentrations of the reaction field. The results show that higher swirl intensity creates more recirculation flow, which reduces the temperature of the reaction zone and, consequently, reduces the thermal NO production. The distributions of flame radicals (OH, CH, C₂) are dependent more on the swirl intensity than the percentage of hydrogen added to methane fuel. The NO concentration at the upper part of the reaction zone is increased with an increase in hydrogen content in the fuel mixture because higher combustibility of hydrogen assists to promote faster chemical reaction, enabling more expansion of the gases at the upper part of the reaction zone, which reduces the recirculation flow. The CO concentration in the reaction zone is reduced with an increase in hydrogen content because the amount of C content is relatively decreased.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 1999년도 제19회 KOSCO SYMPOSIUM 논문집
• /
• pp.129-138
• /
• 1999

In this paper, our main issue is that establishing the control procedure of continuous gas flow rate according to combustion fan RPM. For this, first, we decide the optimum operating condition of gas swirl burner through analysis of combustion characteristics - thermal efficiency, combustion efficiency and exhaust gases such as CO, $CO_{2}$, $O_{2}$, $NO_{x}$ and THC. Second, fuel gas flow rate of gas valve is decided with considering excess air ratio and combustion fan RPM is decided by the target of combustion air flow rate. Finally, experimental operating equation is acquired by regression for gas valve and combustion fan. This equation is the control equation of continuous gas flow rate and always gas flow rate is decided by combustion fan operating RPM.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(2)
• /
• pp.271-276
• /
• 1996

Coolant flow distribution to the assemblies and core coolant/component temperatures should be determined in LMR core steady state thermal-hydraulic performance analysis. Sodium flow is distributed to core assemblies with the overall goal of equalizing the peak cladding midwall temperatures for the peak temperature pin of each pin bundle, thus pin cladding damage accrual and pin reliability. The flow orificing analysis for conceptual design will be performed with Excel spreadsheet program ORFCE which was set up and tested, using the calibration factors based on available analyses data. For the verification of this program, flow orificing calculation for the MDP 840MWth core was performed. The calculational results are satisfactory compared to those of CRIEPI calculation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.250-253
• /
• 2006

The in-pile Section (IPS) is subjected to flow-induced vibration(FIV) due to the flow of the primary coolant and then the structural integrity. The in-pile Section (IPS) of 3-pin Fuel Test Loop(FTL) shall be installed in the vortical hole call IR1 of HANARO reactor core. In order to verify the velocity and displacement both the inside region of IPS at the annular region of IPS, the vibration was measured by varing the flow rate on both regions. The displacements of fuel assembly in the in-pile Section (IPS) were found to be lower than the values of allowable design criteria.

• 대한전기학회논문지
• /
• 제45권3호
• /
• pp.374-379
• /
• 1996

Effects of reactant gas flow rates and starvation on phosphoric acid fuel cell performance were studied. As the reactant gas flow rates increased, the cell performance increased and then the cell maintained constant performance. The optimum flow rates of hydrogen, oxygen and air under galvanostatic condition of 150 mA/cm$_{2}$ are found to be 5cc/min cm$_{2}$ 5cc/min cm$_{2}$ and 15cc/min cm$_{2}$ at room temperature and 1 atm, respectively. Also the open circuit voltage of single cell decreased with increasing oxygen flow rate due probably to the decreased probably to the decreased oxygen pressure in the cathode side. Hydrogen and oxygen starvation resulted in voltage loss of about 5mV and 0-2mV, respectively. The voltage loss was independent of starvation time. These results were discussed from point of view of electrochemical reaction of the cell. (author). 9 refs., 8 figs.

• Journal of Electrochemical Science and Technology
• /
• 제14권1호
• /
• pp.38-50
• /
• 2023

Proton exchange membrane fuel cell (PEMFC) is a portable and clean power generation device. The structural arrangement of the flow field has a significant influence on the delivery efficiency of PEMFC. In this article, a new bionic flow channel is designed based on the inspiration of a spider shape. The branch channel width and branch corner are studied as the focus, and its simulation is carried out by the method of computational fluid dynamics (CFD). The results show that when channel width/rib width and corner of the branch are 1.5 and 130° , respectively, it is the best numerical combination and the cell comprehensive performance is excellent. The final model using this numerical combination is compared with the traditional flow channel model to verify the advancement of this scheme.

• 전기화학회지
• /
• 제12권4호
• /
• pp.329-334
• /
• 2009

본 연구는 연료전지 운전시 전극 촉매 및 전해질막 내에서 발생하는 연료 및 산화제의 산화/환원 반응 메커니즘, 이동현상, 구성품 열화현상 등을 핵자기 공명 (NMR, Nuclear Magnetic Resonance)을 이용하여 연료전지의 분해나 시료 채취 없이 제자리 (in situ) 분석할 수 있는 진단장치용 연료전지 개발에 관한 것이다. NMR에 사용되는 연료전지는 특수하게 제작된 TCD (Toroid Cavity Detector) 탐침 내부에서 작동하여야 하며, TCD 탐침이 가지는 기하학적 제한 요소들로 인해 일반적인 평판형 연료전지와 달리 원통형으로 제작된다. 이로 인해 반응물의 공급이나 생성물의 제거가 어려우며 누수 현상 및 불균일한 압력 분배가 발생하여 성능이 낮다. 따라서, in situ NMR 분석용 연료전지가 가지는 구조상의 특징인 원통형에 적합한 유로를 설계하고 제작하여 물질 전달 특성을 개선해야 할 필요성이 있다. 본 연구에서는 NMR 장비 내의 자기장에 영향을 미치지 않는 비자성 물질을 이용해 원 통형 공기극 유로를 개발하여, 산소의 공급 및 반응물의 제거를 원활하게 하였다. 또한, 체결 압력을막-전극 접합체에 균일하게 분배하여 누수 및 누액을 차단하였다. 이를 통해, 상온에서 약 $36mW/cm^2$의 우수한 성능을 나타내는 in situ NMR 진단용 직접 메탄올연료전지 시스템을 개발하였다.

• 한국가스학회지
• /
• 제19권6호
• /
• pp.47-53
• /
• 2015

이 논문은 굴삭기 엔진용 저압연료 펌프의 연료 유동에 대한 유동장 및 속도, 압력에 관하여 수치해석 방법을 적용하여 연구한 것이다. 연료 펌프의 압력 분포는 로터의 회전각도에 따라 연속적으로 변하며, 특히 회전각도 $40^{\circ}$에서 상대적으로 매우 높은 토출부 압력과 낮은 흡입부 압력이 동시에 발생함을 확인하였다. 또한, 이 각도에서 누설유동 유속이 가장 증가함을 알 수 있었다. 그리고 연료 펌프의 로터 회전수의 증가에 따라 평균토출유량이 선형적으로 증가하였고, 간극크기가 감소함에 따라 토출유량이 로터 기어 사이의 배제용적으로부터 계산된 이론적 토출유량 0.0712kg/s 으로 접근하는 것을 확인할 수 있었다.

• 전기화학회지
• /
• 제10권4호
• /
• pp.245-251
• /
• 2007

주어진 연료전지면적에서 반응면적이 넓을수록 성능이 향상되는 연료전지는 좁은 폭의 채널을 여러 개 존재하게 하는 구조를 선호하지만 채널 폭이 좁아질수록 압력이 커지는 문제가 고려되어져야 한다. 그러나 현재 채널 구조에 따른 압력에 대한 연구는 많이 진행되어져 왔지만 대부분 반응을 고려하지 않았으며, 반응을 고려한 경우에 어떤 경향을 나타내는지 알아보는 것이 연료전지 유로설계에 있어 매우 중요하다. 본 논문에서 화학반응을 고려한 평행류, 90도 밴드형, serpentine 세가지 종류의 유로채널를 가진 연료전지를 수치 해석하여 반응을 고려하지 않은 경우와 마찰계수(fRe), 속도, 압력강하를 비교하여 본 결과 parallel과 bend 형태의 채널은 반응을 고려한 경우 반응에 의한 밀도의 감소에 따라 근소하게 감소한 것을 알 수 있었다. 그러나 serpentine채널은 다공성매체인 확산층을 통해 인접한 채널로 가스가 이동하는 bypass flow 영향에 의하여 상대적으로 낮은 압력강하를 나타내는 것을 알 수 있었다.