• Korean Journal of Materials Research
• /
• v.21 no.11
• /
• pp.617-622
• /
• 2011

The effect of oxygen on the shape memory characteristics in Ti-18Nb-6Zr-XO (X = 0-1.5 at%) biomedical alloys was investigated by tensile tests. The alloys were fabricated by an arc melting method at Ar atmosphere. The ingots were cold-rolled to 0.45 mm with a reduction up to 95% in thickness. After severe cold-rolling, the plate was solution-treated at 1173 K for 1.8 ks. The fracture stress of the solution-treated specimens increased from 450 Mpa to 880 MPa with an increasing oxygen content up to 1.5%. The fracture stress increased by 287MPa with 1 at% increase of oxygen content. The critical stress for slip increased from 430 MPa to 695 MPa with an increasing oxygen content up to 1.5 at%. The maximum recovery strain of 4.1% was obtained in the Ti-18Nb-6Zr-0.5O (at%) alloy. The martensitic transformation temperature decreased by 140 K with a 1.0 at% increase in O content, which is lower than that of Ti-22Nb-(0-2.0)O (at%) by 20 K. This may have been caused by the effect of the addition of Zr. This study confirmed that addition of oxygen to the Ti-Nb-Zr alloy increases the critical stress for slip due to solid solution hardening without being detrimental to the maximum recovery strain.

• Journal of the Korean Society of Radiology
• /
• v.7 no.5
• /
• pp.359-364
• /
• 2013

Femur is the largest bone in the human body which supports the weight of body. A long pipeline shape of femur has little cancellous bone, so that regeneration is difficult when fracture happens. The fracture caused by an accident most frequently occurs at diaphysis. IM Nailing is the surgical method that implants an IM Nail into a medullary cavity for the fixation of fracture parts. However, a secondary fracture may happen if an IM Nail does not penetrate at the center of femur. In this study, a patient-specific femur was manufactured by a 3D printer using the computed tomography images scanned before surgery, which was used for the simulation of IM Nailing. It is expected that this result may prevent the secondary damage, reduce surgical operation time, and increase the precision.

• Computers and Concrete
• /
• v.1 no.4
• /
• pp.389-400
• /
• 2004

The examinations carried out have confirmed a relationship existing between the character of fracture surfaces and the composition and structure of (basalt and gravel) concretes. For both concretes investigated, a very good correlation was obtained between the profile line development factor, $R_L$, and the fracture surface development factor, $R_S$. With the increase in the $R_L$ parameter, the fracture surface development factor $R_S$ also increased. Agreement between the proposed relationship of $R_S=f(R_L)$ and the proposal given by Coster and Chermant (1983) was obtained. Stereological examinations carried out along with fractographic examinations made it possible to obtain a statistical model for the determination of $R_L$ (or $R_S$) based on the volume of air voids in concrete, $V_{air}$, the specific surface of air pores, $S_V_{air}$ the specific surface of coarse aggregate, $S_{Vagg.}$, and the volume of mortar, $V_m$. An effect of coarse aggregate type on the obtained values of the profile line development factor, $R_L$, as well as on the relationship $R_S=f(R_L)$ was observed. The increment in the fracture surface development factor $R_S$ with increasing $R_L$ parameter was larger in basalt concretes than in gravel concretes, which was a consequence of the level of complexity of fractures formed, resulting chiefly from the shape of coarse aggregate grains.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.9
• /
• pp.1299-1304
• /
• 2010

We examined the working fracture behavior of a silicon-steel strip caused by deformation deviation by performing a pilot rolling test. The deformation deviation resulted in the edges (or center portion) of the strip being stretched and the other parts being compressed in the rolling direction; this was because of different degrees of deformation in these parts. We designed roll grooves shape to reflect the role of roll bending, which generates waviness in the strip in an actual cold rolling process, into the pilot rolling test. The material used in the rolling test was highsilicon steel (about 3%). The results of the test showed that the type of fracture in the strip specimen varied with the magnitude of the deformation deviation. The tensile stress produced at the strip edges because of the center waviness in the rolling direction was a crucial factor that resulted in edge cracking and a zigzag-shaped fracture at the center.

• Journal of Korean Foot and Ankle Society
• /
• v.18 no.4
• /
• pp.178-182
• /
• 2014

Purpose: The purpose of this study was to evaluate the frequency of troughing and stress fracture, which are the major complications of scarf osteotomy, and to suggest methods to prevent these complications. Materials and Methods: We reviewed 243 cases of 137 patients treated with the scarf osteotomy for hallux valgus from January 2005 to December 2012. The mean follow-up period was 2.8 years. During the scarf osteotomy, a long oblique longitudinal osteotomy was performed in order to decrease the possibility of troughing and stress fracture. Radiographs of lateral view of the foot were obtained and the thicknesses of the first metatarsal base at the sagittal plane were measured and compared. Results: There was no troughing during fragment translation and screw fixation intraoperatively. Radiographs of lateral view of the foot taken preoperatively and at the last follow-up showed that the mean thickness of the first metatarsal was 22.4 mm preoperatively and 21.6 mm at the last follow-up, with a mean difference of 0.8 mm. And no stress fracture was observed. Conclusion: To prevent troughing and stress fracture, a long oblique longitudinal cut, parallel to the first metatarsal plantar surface, was performed, making both ends of the proximal segment truncated cone-shape, and securing the strong bony strut of the proximal segment. No troughing or stress fracture was experienced with scarf osteotomy.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.182-192
• /
• 2022

Brittle feature is one of the fracture behaviors of structure s and has a great influence on the seismic performance of structure materials. The load velocity acts as one of the main causes of brittle fracture, and in particular, in situations such as earthquakes, a high load velocity acts on buildings. However, most of the seismic performance evaluation of the domestic and external steel connections is conducted through static experiments. Therefore, there is a possibility that brittle fracture due to factors such as degradation of material toughness and reduction of maximum deformation rate due to high load velocity during an earthquake was not sufficiently considered in the existing seismic performance evaluation. This study conducts a static test at a low load velocity according to the existing experimental method and a dynamic test at a high load velocity using a shaking table, respectively. It compares and analyzes the fracture shape and structural performance according to the results of each experiment, and finally analyzes the effect of the load velocity size on the seismic performance of the connection.

• Archives of Plastic Surgery
• /
• v.35 no.5
• /
• pp.597-602
• /
• 2008

Purpose: Presently, silicone rubber is chosen most frequently for nasal augmentation. However, there is a possibility of extrusion with this material. Sometimes, noses are prone to be traumatized, and then silicone rubber has a possibility of deformity or deviation resulting in trauma. We experienced cases with complications and traumatic deformities after the augmentation rhinoplasty. Methods: A retrospective review was performed to determine the characteristics of the implanted nasal silicone prosthesis after trauma. The patients' data such as deviation of implant, shape of fracture, age and sex of the patient, time of treatment, operative methods were reviewed. From March 2001 to March 2008, this study was performed in 30 patients. The patients were 25 females and 5 males, from 24 to 60 years of age, with an average of 42. All patients had previous augmentation rhinoplasty with silicone implant. Results: All of the 30 patients were confirmed as deviation of silicone and nasal bone fractures in the facial bone CT scan. The most common cause of fracture was traffic accident. The classification of nasal trauma after augmentation was done by facial bone CT. Class I: Deviation of silicone without nasal bone fracture without extrusion(12 cases, 40%), Class II: Deviation of silicone without nasal bone fracture and with extrusion(4 cases, 13%), Class III: Deviation of silicone with nasal bone fracture and without extrusion(8 cases, 27%), Class IV: Deviation of silicone with nasal bone fracture and with extrusion(3 cases, 10%), Class V: Mild deviation of silicone with nasal bone fracture(3cases, 3%). Specially, the comminuted or trapezoid nasal fracture was confirmed in 11 cases(Class III, IV). Conclusion: The problems of silicone implant have generally been related to foreign body reactions, rigidity of the material, encapsulation, infections, and extrusion. We experienced 11 cases of comminuted or comminuted trapezoid shaped fracture below nasal implant. So, we think this phenomenon could be used in late problem of silicone implant.

• Journal of Mechanical Science and Technology
• /
• v.20 no.4
• /
• pp.473-481
• /
• 2006

Predicting fatigue life by numerical methods was almost impossible in the field of rubber materials. One of the reasons is that there is not obvious fracture criteria caused by nonstandardization of material and excessively various way of mixing process. But, tearing energy as fracture factor can be applied to a rubber-like material regardless of different types of fillers, relative to other fracture factors and the crack growth process of rubber could be considered as the whole fatigue failure process by the existence of potential defects in industrial rubber components. This characteristic of fatigue failure could make it possible to predict the fatigue life of rubber components in theoretical way. FESEM photographs of the surface of industrial rubber components were analyzed for verifying the existence and distribution of potential defects. For the prediction of fatigue life, theoretical way of evaluating tearing energy for the general shape of test-piece was proposed. Also, algebraic expression for the prediction of fatigue life was derived from the rough cut growth rate equation and verified by comparing with experimental fatigue lives of dumbbell fatigue specimen in various loading condition.

• Journal of Yeungnam Medical Science
• /
• v.5 no.1
• /
• pp.43-48
• /
• 1988

We retrospectively analysed 22 patients pelvic CT, in whom the acetabular fracture were suspected in plain film. And compared and analysed the computed tomogram findings and plain radiographic findings. The results were as follows. CT enables better evaluation of shape, extent, and degree of separation of fragment. CT was helpful in detecting the combinded fracture and soft tissue injuries. CT showed intraarticular loose bodies, which were invisible on plain film. In patients with pelvic trauma, no necessary changing position during CT examination. CT was useful demonstrates the remnant of intraarticular osseous fragment and adequacy of reduction after surgery.

• Journal of Korea Foundry Society
• /
• v.18 no.6
• /
• pp.563-569
• /
• 1998

A Study on microstructure and elevated temperature strength of 18Cr-2Mo ferritic stainless steel castings strengthened by alloying small amounts of titanium and carbon, has been conducted. The morphology of titanium carbides showed spherical in shape and their distribution depended on the amount of alloying elements. Maximum density ($7{\times}10^5/cm^2$) of titanium carbides has been formed in the alloy containing 2.0 wt.% titanium and 0.5 wt.% carbon as alloying elements and the size of carbide particles is in the range of 0.5 to $3.0\;{\mu}m$. High temperature tensile and fatigue strength of this alloy were the highest among the alloys tested in this research. The fracture mode of the alloys containing alloying elements less that 2.0 wt.% titanium and 0.5 wt.% carbon showed intercrystalline fracture at room temperature, while the alloys containing higher amounts of alloying elements showed transcrystalline fracture. All of the alloys showed creep or ductile rupture mode at elevated temperature.