• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.10a
• /
• pp.182.2-182
• /
• 2000

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.3
• /
• pp.31-37
• /
• 2009

Cu-Cu thermo-compression bonding process was successfully developed as functions of the $N_2+H_2$ forming gas annealing conditions before and after bonding step in order to find the low temperature bonding conditions of 3-D integrated technology where the quantitative interfacial adhesion energy was measured by 4-point bending test. While the pre-annealing with $N_2+H_2$ gas below $200^{\circ}C$ is not effective to improve the interfacial adhesion energy at bonding temperature of $300^{\circ}C$, the interfacial adhesion energy increased over 3 times due to post-annealing over $250^{\circ}C$ after bonding at $300^{\circ}C$, which is ascribed to the effective removal of native surface oxide after post-annealing treatment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.304.1-304.1
• /
• 2016

We have investigated the effect of plasma nitridation of atomic layer deposited-Al2O3 films of monocrystalline Si wafers and the thermal properties of nitridated Al2O3 films. Nitridation was performed on Al2O3 to form aluminum oxynitride (AlON) using NH3 plasma treatment in a plasma-enhanced chemical vapor deposition and it was conducted at temperature of $400^{\circ}C$ with various plasma power condition. After nitridation, we performed firing and forming gas annealing (FGA). For each step, we have observed the minority carrier lifetime and the implied Voc by using quasi-Steady-State photoconductance (QSSPC). We confirmed a tendency to increase the minority carrier lifetime and the implied Voc after the nitridation. On the other hand, the minority carrier lifetime and the implied Voc was decreased after Firing and forming gas annealing (FGA). To get more information, we studied properties of the plasma treated Al2O3 films by using Secondary Ion Mass Spectroscopy (SIMS) and X-ray Photoelectron Spectroscopy (XPS).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.462-462
• /
• 2014

The effect of rear passivation for passivated emitter and rear cell (PERC) using ozone and H2O oxidant of atomic layer deposited (ALD) Al2O3 was studied by post-annealing in N2 and forming gas ambients. Rear surface of PERC solar cell was passivated by Al2O3 grown by ALD with ozone and H2O oxidant. Al2O3 grown by ALD with ozone oxidant has been known to have many advantages, such as lower interface defects, low leakage current density. Its passivation quality is better than Al2O3 with H2O. Al2O3 layer with 10 nm and 20 nm thickness was grown at $150^{\circ}C$ with ozone oxidant and at $250^{\circ}C$ with H2O oxidant. And then each samples were post-annealled at $450^{\circ}C$ in N2 ambients and at $850^{\circ}C$ in forming gas ambients. The passivation quality was investigated by measuring the minority carrier lifetime respectively. We examined atomic layer deposited Al2O3 such as growth rate, film density, thickness, negative fixed charge density at AlOx/Si interface, and reflectance. The influences of process temperature and heat treatment were investigated using Sinton (WCT-120) by Quasi-Steady State Photoconductance (QSSPC) mode. Ozone-based ALD Al2O3 film shows the best carrier lifetime at lower deposition temperature than H2O-based ALD.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.129-130
• /
• 2008

Polycrystalline silicon (poly-Si) Schottky barrier thin film transistors (SB-TFT) are fabricated by erbium silicided source/drain for n-type SB-TFT. High quality poly-Si film were obtained by crystallizing the amorphous Si film with excimer laser annealing (ELA) or solid phase crystallization (SPC) method. The fabricated poly-Si SB-TFTs have a large on/off current ratio with a low leakage current. Moreover, the electrical characteristics of poly-Si SB TFTs are significantly improved by the additional forming gas annealing in 2 % $H_2/N_2$, because the interface trap states at the poly-Si grain boundaries and at the gate oxide/poly-Si channel decreased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.117-118
• /
• 2008

High-pressure deuterium annealing process is proposed and investigated for enhanced electrical and reliability properties of 512Mb DDR2 DRAM without increase in process complexity. High pressure deuterium annealing (HPDA) introduced during post metal anneal (PMA) improves not only DRAM performance but also reliability characteristics of MOSFET. Compared with a control sample annealed in a conventional forming gas, additional annealing in a high pressure deuterium ambient at $400^{\circ}C$ for 30 min decreased G1DL current and junction leakage. The improvements can be explained by deuterium incorporation at $SiO_2$/Si substrate interface near isolation trench edge.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.706-711
• /
• 2018

In this work, we have investigated the characteristics of 4H-SiC metal-oxide-semiconductor (MOS) devices with silicon oxynitride (SiON) insulator using plasma enhanced chemical vapor deposition (PECVD). After post metallization annealing, the trap densities of the fabricated devices decreased significantly. In particular, the device annealed at $500^{\circ}C$ in forming gas ambient exhibited excellent MOS characteristics along with negligible hysteresis, which proved the potential of PECVD SiON as an alternative gate insulator for use in 4H-SiC MOS device.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.6
• /
• pp.236-239
• /
• 2002

Si nanocrystallites thin films on P-type (100) Si substrate have been fabricated by pulsed laser deposition using a Nd:YAG laser. After deposition, samples were annealed in several environmental gases ;It the temperature range of 400 to $800^{\circ}C$ Hydrogen passivation was then performed in the forming gas (95 % $N_2$ + 5 % $H_2$) for 1 hr. Strong violet-indigo photoluminescence has been observed at room temperature on nitrogen ambient-annealed Si nanocrystallites. We report the variation of photoluminescence (PL) properties of Si thin films by changing annealing temperatures and by using hydrogen passivation. The results could suggest that the origin of violet-indigo PL should be related to the Quantum size effect of Si nanocrystallite.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.6
• /
• pp.462-465
• /
• 2009

Schottky barrier thin film transistors (SB-TFT) on polycrystalline silicon(poly-Si) are fabricated by platinum silicided source/drain for p-type SB-TFT. High quality poly-Si film were obtained by crystallizing the amorphous Si film with excimer laser annealing (ELA) or solid phase crystallization (SPC) method, The fabricated poly-Si SB-TFTs showed low leakage current level and a large on/off current ratio larger than 10), Significant improvement of electrical characteristics were obtained by the additional forming gas annealing in 2% $H_2/N_2$ ambient, which is attributed to the termination of dangling bond at the poly-Si grain boundaries as well as the reduction of interface trap states at gate oxide/poly-Si channel.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.9
• /
• pp.423-429
• /
• 2002

RuOx thin films were fabricated by the method of liquid delivery MOCVD using Ru(C$_{8}$ $H_{13}$ $O_2$)$_3$ as the precursor and their thermal effects and conductivity were investigated. Ru films deposited at 25$0^{\circ}C$ were annealed at $650^{\circ}C$ for 1min with Ar, $N_2$ or N $H_3$ ambient. The changes of the micro-structure, the surface morphology and the electrical resistivity of the Ru films after annealing were studied. Ar gas was more effective than $N_2$ and N $H_3$ gases as an ambient gas for the post annealing of the Ru films, because of smaller resistivity and denser grains. The X-ray diffraction and X-ray photoelectron spectroscopy results indicate that the Ru $O_2$ phase and the silicidation are not observed regardless of the ambient gases. The minimum resistivity of the Ru film is found to have the value of 26.35 $\mu$Ω-cm in Ar ambient. Voids were formed at Ru/TiN interface of the Ru layer after annea1ing in $N_2$ ambient. The $N_2$ gas generated due to the oxidation of the TiN layer accumulated at the Ru/TiN interface, forming bubbles; consequently, the stacked film may peel off the Ru/TiN interface.e.