• Journal of information and communication convergence engineering
• /
• v.3 no.4
• /
• pp.176-178
• /
• 2005

This paper presents closed-form expressions for exact bit error rate of MSK and OQPSK systems employing an adaptive antenna array at base station to eliminate co-channel interference. The channels under consideration are AWGN and one-path flat Rayleigh fading with AWGN. Computer simulation is carried out to confirm the theoretical results.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.9
• /
• pp.54-63
• /
• 1993

Quantization error, generated by the quantization process of an image, is inherent in computer vision. Because, especially in stereo vision, the quantization error in a 2-D image results in position errors in the reconstructed 3-D scene, it is necessary to analyze it mathematically. In this paper, the analysis of the probability density function (pdf) of quantization error for a line-based stereo matching scheme is presented. We show that the theoretical pdf of quantization error in the reconstructed 3-D position information has more general form than the conventional analysis for pixel-based stereo matching schemes. Computer simulation is observed to surpport the theoretical distribution.

• The Bulletin of The Korean Astronomical Society
• /
• v.40 no.2
• /
• pp.40.1-40.1
• /
• 2015

Off-axis reflective optical systems have attractive advantages relative to their on-axis or refractive counterparts, for example, zero chromatic aberration, no obstruction, and a wide field of view. For the efficient operation of off-axis reflective system, the surface accuracy of freeform mirrors should be higher than the order of wavelengths at which the reflective optical systems operate. Especially for applications in shorter wavelength regions, such as visible and ultraviolet, higher surface accuracy of freeform mirrors is required to minimize the light scattering. In this work, we propose the error compensation algorithm (ECA) for the correction of wavefront errors on freeform mirrors. The ECA converts a form error pattern into polynomial expression by fitting a least square method. The error pattern is measured by using an ultra-high accurate 3-D profilometer (UA3P, Panasonic Corp.). The measured data are fitted by two fitting models: Sag (Delta Z) data model and form (Z) data model. To evaluate fitting accuracy of these models, we compared the fitted error patterns with the measured error pattern.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.4
• /
• pp.97-103
• /
• 2001

Accuracy of a machined part is determined by the relative motion between the cutting tool and the workpiece. One of the important factors which affects the relative motion is the geometric errors of a machine tool. In this study, firstly, geometric errors are measured by laser interferometer, and the positioning error of each control point selected uniformly on the control surface CAD model can be estimated from th oirm shaping model and geometric error data base. Where a form shaping function is derived from the link of homogeneous transformation matrix. Secondly, control points are shifted to the estimated amount of positioning errors. A new control surface is modeled with NURBS(Non Uniform Rational B-Spline) surface approximation to the shifted control points. By generating tool paths to the redesigned control surface, we reduce the machining error quite.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.2
• /
• pp.155-162
• /
• 2020

Since the third industrial revolution has been started in the 1980s, the form of buildings has been varied and atypical by the development of building technology. Such free-form building has a curved shape unlike the existing standard buildings, and to realize this, it is necessary to manufacture the free-from panel. The shape of the free-form panel must satisfy a limited error ratio compared with the design shape, and the technology to produce free-form panels is very difficult. However, there are many problems such as enormous cost and construction waste generation when implementing free-from construction. Therefore, the development of free-form panel manufacturing technology should be made to solve the problems caused by the free-form construction. In this study, the error rate analysis of the mixed mortar panel was conducted by selecting the proper mixing ratio of the mixed mortar for the shape of the free-form panel.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.5
• /
• pp.449-456
• /
• 2019

Recent developments in architectural technologies and programs have enabled architects to think creatively and design free-form architecture. however, there are many problems in the production technology of FCP(Free-Form Concrete Panel). In particular, reduced accuracy due to lack of free-form panel production technology can lead to redesign of buildings as a result, problems such as an increase in construction cost and period. Therefore, this experiment aimed to compensate the decrease of the accuracy according to the displacement difference and to derive the proper mixing ratio for maintaining the shape during the free-form panel curing. In this study, molds were made using paraffin that is a recyclable phase change material. Concrete Panel is usually produced from Portland cement, dead burn magnesia, phosphate, borax and fine aggregate. In this study, four mixing ratios of FCP were selected after each material was blended to determine the proper blending ratio of the fluidity phase, the water absorption rate and the water content of the test piece. FCP was fabricated on the basis of the selected four compounding ratios and thickness and error rate were measured. Based on the error rate of the measured FCP, the quality standard was satisfied among the four compounding ratios.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.6C
• /
• pp.561-569
• /
• 2003

In this paper, for my linear orthogonal space-time block including the orthogonal space-time codes introduced by Alamouti［1］, Tarokh［14］, and Xia［11］, the exact expression for the pairwise error probability in the slow Rayleigh fading channel is derived in terms of the message symbol distance between two message vectors rather than the codeword symbol distance between two transmitted codeword matrices. Using the one-dimensional component symbol error probability, the exact closed form expressions for the symbol error probability of linear orthogonal space-time codes are derived for QPSK, 16-QAM, 64-QAM, and 256-QAM.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.5
• /
• pp.66-72
• /
• 1997

In this paper, we propose a method improving the accuracy of th eregistration coefficients calculated form two range images considering the measurement error. The employed range finder is based on triangulation and the depth measurement error is described with an error covariance matrix, which is based on thesensitivity of the range measurements. Experimental results demonstrate that the registration coefficients obtained with the proposed method are better than the results when the measurment errors are neglected.

• 한국기계연구소 소보
• /
• s.20
• /
• pp.21-26
• /
• 1990

In order to satisfy the industrial requirements to measure the rotational error motion of main spindles and to find out the source of the error motion, some measuring systems were made. Their measuring principle are based on the 3-point roundness measurement. In these measuring systems, the measurements are processed by digital calculation technique and the form error and the rotational error motion of main spindles are spearated. In the present paper, the principle of 3-point metnod is introduced and some application examples are shown.

• Journal of the Korean Society of Safety
• /
• v.23 no.4
• /
• pp.13-18
• /
• 2008

This study deals with finish roll forming by forced displacement can be conceived as a method of eliminating errors in conventional form rolling under constant loads. This method produces a high-precision tooth profile by low-speed form rolling when a high rigid screw or cam is used at the pressurized section. Tooth profile is decided in the beginning of roll forming and ${\delta}_{max}$ mainly increases if the number of roll forming process is increased. Gear class is improved by one or two class after roll forming if the gear has convex type error and pressure angle error in KS 4 class. If the gear have concave type error and pressure angle error and pressure angle error, gear class is not improved in theory, but improved a little in practice. In the finishing roll forming, it inevitably yields both the concaving of tooth profile and plastic deflection of addendum of teeth. Experiments show that the concaving and the plastic deflection are successfully reduced, the accuracy of tooth profile reaches to KS 0 class.