• Journal of applied mathematics & informatics
• /
• 제39권1_2호
• /
• pp.31-43
• /
• 2021

A homogeneous circular disk undergoing a contact force is considered to investigate the thermo-elastic characteristics, and the inquiry is based on the variations of outer surface temperature and angular velocity. The intensity of stresses grows with the increase of outer surface temperature, and the circumferential strain reacts more sensitively to the change of outer surface temperature than the radial strain. In general, higher angular velocity produces; (i) larger expansion in the radial direction, (ii) smaller displacement in the circumferential, (iii) diminished intensity in the stresses. It is demonstrated that outer surface temperature and angular velocity are critical factors in the determination of thermo-elastic characteristics of homogeneous circular disks subjecting to a contact force. The results obtained can be applied on the design of a homogeneous circular cutter to promote proper and reliable thermos-elastic characteristics in service by the proper operation of these parameters.

• 오토저널
• /
• 제4권3호
• /
• pp.56-68
• /
• 1982

This paper presents analytic solutions of defection and their resonance diagrams for a uniform beam of infinite length subjected to an constant axial force and moving transverse load simultaneously. Steady solutions are obtained by a time-independent coordinate moving with the load. The supporting foundation includes damping effects. The influences of the axial force, the damping coefficient and the load velocity on the beam response are studied. The limiting cases of no damping and critical damping are also investigate. The profiles of the deflection of the beam are shown graphically for several values of the load speed, the axial force and damping parameters. Form the results, following conclusions have been reached. 1. The critical velocity .THETA.cr decreases as the axial compressive force increases, but increases as the axial tensile force increase. 2. At the critical velocity .THETA.cr the deflection have a tendency to decrease as the axial tensile force increases and to increase gradually as the axial compressive force increases. 3. In case if relatively small dampings, the deflection increases suddenly as the velocity of the moving load approaches the critical velocity, and it reachs its maximum at the critical velocity, and it decreases and become greatly affected by the axial force as the velocity increases further. 4. in case of relatively large dampings, as the velocity increases the deflection decreases gradually and it is affected little by the axial load.

• 한국정밀공학회지
• /
• 제23권8호
• /
• pp.47-53
• /
• 2006

The purpose of this study was to investigate the significant characteristics in spray of industrial etch-nozzle for the design of process. The experiment was carried out with different spray pressure and industrial nozzle in wet etch. The characteristics of liquid spray, such as axial velocity and sauter mean diameter measurements were obtained by PDA. And impact force was calculated from spray characteristics. It was found that the fluid with higher spray pressure resulted in the smaller SMD and the higher droplet velocity and impact force. The depth of etch was increased in case of high spray pressure. In the case of injection angle oscillated between $20^{\circ}$, the result indicated constant effect of etch. The correlation between the spray characteristics and etch ones were analyzed. The depth of etch had good positive correlation with axial velocity and impact force. The result clearly shows that the characteristics in wet etch are strongly related to the spray characteristics with process.

• 한국생산제조학회지
• /
• 제22권3호
• /
• pp.447-451
• /
• 2013

In this study, a shock absorber whose orifice area changes according to the oil pressure inside the absorber is developed. The orifice widens and narrows when the oil pressure is high and low, respectively; thus, the orifice area changes according to the oil pressure, in other words, according to the extension/compression velocity. It is well known that the damping force can be expressed as $C{\cdot}v^{\alpha}$. For fluid film damping, the force is proportional to velocity, i.e., ${\alpha}=1$, and for orifice damping, it is proportional to the square of velocity, i.e., ${\alpha}=2$. The shock absorber proposed in this paper can exhibit different relationships between the damping force and velocity because the orifice area changes according to the induced oil pressure. The motivation of this study is to develop a method for designing a shock absorber with desired values of C and ${\alpha}$ which is not just 1 or 2. Theoretical and experimental studies have been conducted to verify the damping characteristics of the shock absorber. The effect of some major design parameters on damping characteristics has been also examined to relate the design parameters to the damping characteristics.

• 한국대기환경학회지
• /
• 제16권2호
• /
• pp.179-190
• /
• 2000

The main object of this study was to investigate experimentally the characteristics of electrostatic cyclone-bag filter with upper tangential inlet in order to overcome the low collection efficiency for the submicron particle and high pressure drop which were main problems of general fabric bag filters. The experiment was carried out for the analysis of collection efficiency and pressure drop of electrostatic cyclone-bag filter comparing to those of fabric bag filter with various experimental parameters such as the inlet velocity(filtration velocity) and applied voltage etc. In the results the upper tangential inlet type showed higher collection efficiency for submicron particles below 2 ${\mu}{\textrm}{m}$ in diameter than that of center inlet and over 99.9% for overall collection efficiency. Pressure drop reduction ratios were shown as 40-50% for the applied voltage 0kV by centrifugal force and 70-90% for 20k V by the centrifuga and electrostatic force with the tangential inlet velocity (12-21m/s)

• 한국정밀공학회지
• /
• 제20권5호
• /
• pp.39-39
• /
• 2003

As the design rules in semiconductor manufacturing process become more and more stringent, the higher degree of planarization of device surface is required for a following lithography process. Also, it is great challenge for chemical mechanical polishing to achieve global planarization of 12” wafer or beyond. To meet such requirements, it is essential to understand the CMP equipment and process itself. In this paper, authors suggest the velocity distribution on the wafer, direction of friction force and the uniformity of velocity distribution of conventional rotary CMP equipment in an analytical method for an intuitive understanding of variation of kinematic variables. To this end, a novel dimensionless variable defined as “kinematic number” is derived. Also, it is shown that the kinematic number could consistently express the velocity distribution and other kinematic characteristics of rotary CMP equipment.

• 한국정밀공학회지
• /
• 제20권5호
• /
• pp.29-38
• /
• 2003

As the design rules in semiconductor manufacturing process become more and more stringent, the higher degree of planarization of device surface is required for a following lithography process. Also, it is great challenge for chemical mechanical polishing to achieve global planarization of 12” wafer or beyond. To meet such requirements, it is essential to understand the CMP equipment and process itself. In this paper, authors suggest the velocity distribution on the wafer, direction of friction force and the uniformity of velocity distribution of conventional rotary CMP equipment in an analytical method for an intuitive understanding of variation of kinematic variables. To this end, a novel dimensionless variable defined as “kinematic number” is derived. Also, it is shown that the kinematic number could consistently express the velocity distribution and other kinematic characteristics of rotary CMP equipment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.50-52
• /
• 2004

Mobility of an indoor wheeled robot is affected by adhesion force that is related to various floor conditions. When the adhesion force between driving wheels and the floor decreases suddenly, the robot has slip state. First of all, this paper models adhesion characteristics and slip in wheeled robot. Secondly, the paper proposes estimation method of adhesion force coefficient according to slip velocity. In oder to overcome this slip problem, optimal slip velocity must be decided for stable movement of wheeled robot. The paper proposes an anti-slip control system based on an ordinary disturbance observer, that is, the anti-slip control is achieved by reducing the driving torque enough to give maximum adhesion force coefficient. These procedure is implemented using a Pioneer 2-DXE parameter.

• 대한기계학회논문집A
• /
• 제29권10호
• /
• pp.1307-1314
• /
• 2005

The most important factor of the traffic accident on the wet road is a tire slip caused by hydroplaning. Meanwhile, hydroplaning characteristics are influenced very greatly by the vehicle velocity, so it is very important to reveal the relation between hydroplaning and the vehicle velocity. Since the experiment study is considerably limited, recently the numerical simulation using finite element method(FEM) and finite volume method(FVM) is widely adopted. In this paper, the effect of the vehicle velocity on the hydroplaning characteristics is investigated through the hydroplaning analysis using MSC/Dytran.

• 한국구조물진단유지관리공학회 논문집
• /
• 제11권6호
• /
• pp.181-192
• /
• 2007

외부 강선의 긴장력 측정 기법은 국내의 경우, 거의 전무한 연구 실적을 가지고 있는 실정이다. 따라서 본연구의 목적은 강선의 긴장력을 유도 초음파법을 이용하여 측정하는 것으로 이를 위하여 시험용 웨지 및 측정 시스템을 설계 제작하여 강선에 가하여지는 긴장력 변화에 따른 초음파의 특성을 분석하여 그 상관관계를 도출하고, 이를 기반으로 초음파 특성 변화로부터 강선에 가하여지는 긴장력을 측정할 수 있는 기법을 개발하고자 한다. 이에 긴장력-속도변화의 관계식들을 구하여 제시하였으며, 제시된 식들의 오차는 약 3.92~8.77%로 나타나 현장적용이 가능할 것으로 판단된다.