• Progress in Superconductivity and Cryogenics
• /
• v.20 no.3
• /
• pp.21-27
• /
• 2018

It is difficult to fabricate and maintain moving parts of expander at cryogenic temperature. This paper describes numerical analysis and experimental investigation on a cryogenic reciprocating expander without moving piston. An intake valve which takes high-pressure gas, and an exhaust valve which discharges low-pressure gas, are connected to a tube. The inside pressure of the tube is pulsated for work production. This geometric configuration is similar to that of pulse tube refrigerator but without regenerator. An orifice valve and a reservoir are installed to control the phase of the mass flow and the pressure. At the warm end, a heat exchanger rejects the heat which is converted from the produced work of the expanded gas. For the numerical analysis, mass conservation, energy conservation, and local mass function for valves are used as the governing equations. Before performing cryogenic experiments, we carried out the expander test at room temperature and compared the performance results with the numerical results. For cryogenic experiments, the gas is pre-cooled by liquid nitrogen, and then it enters the pulse tube expander. The experiments are controlled by the opening of the orifice valve. Numerical analysis also found the expander conditions that optimize the expander performance by changing the intake pressure and valve timing as well as the opening of the orifice valve. This paper discusses the experimental data and the numerical analysis results to understand the fundamental behavior of such a newly developed non-mechanical expander and elucidate its potential feature for cryogenic application.

• Aerospace Engineering and Technology
• /
• v.11 no.1
• /
• pp.68-77
• /
• 2012

Flow characteristics of base region of small scaled 4 nozzle clustered engine has been analyzed with CFD approach along with the tests of numerical methods. The numerical test shows that Spalart-Allmaras turbulence model is appropriate for the present research. Plumes expanded from nozzles exits collide with each other and make high pressure stagnation region. Some of collided plumes expand again reversely into the base region with supersonic speeds. The reversed plume in the base region goes out to the outer region through the minimum vent area formed by the nearest nozzle exterior surfaces. But different from the empirical theory, the minimum vent area does not play a role of throat. Additionally the temperature of the nozzle inner surface strongly affects the temperature of the reversed plumes.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.3
• /
• pp.547-554
• /
• 2005

Ethernet has been given a greater attention recently due to tendency of unifying most of transmission technique to ethernet. This paper studied the design of MAC which contains high layer interface, transmit engine, flow control block, receive engine, reconciliation sublayer, configuration block, statistics block, and XGMll interface block. Performance evaluation was performed using C language for 10cbps ethernet Data Link to design the optimum hardware, then internal FIFO and initial parameters were evaluated. When offered load is $95\%$, the size of the internal FIFO is required 512-word. When offered load is $97\%$, the size of the internal FIFO is required 1024-word. Based on the result of performance evaluation, MAC was designed in VHDL Language and verified using simulator. MAC core that processes 64-bit data, operates at 168.549MHz and hence supports the maximum 10.78Gbps. The designed MAC core is applicable to an area that needs a high-speed data processing of 10Gbps or more.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.5
• /
• pp.812-820
• /
• 2006

Ethernet has been given a greater attention recently due to tendency of unifying most of transmission technique(not only LAN, but MAN and WAN) to ethernet. Performance evaluation was performed using C language for 10Gbps ethernet Data Link to design the optimum hardware, then internal FIFO size was evaluated. In this paper, MAC core for 10Gbps ethernet which contains high layer interface, transmit engine, flow control block, receive engine, reconciliation sublayer, configuration block, statistics block, and XGMII interface block was designed using VHDL language and Xilinx 6.2i tool and verified using Model_SIM 5.7G simulator. According to the specification of 10Gbps ethernet, MAC core with 64-bit data path should support 156.25MHz in order to support 10Gbps. The designed MAC core that process 64-bit data, operates at 168.549MHz and hence supports the maximum 10.78Gbps data processing. The designed MAC core is applicable to an area that needs a high-speed data processing of 10Gbps or more.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.9
• /
• pp.1700-1710
• /
• 1992

The boundary element method is applied to determine thermal stress intensity factors for a cusp crack in transient state. In the steady temperature field, numerical values of thermal stress intensity factors for a Grifith crack and a symmetric lip cusp crack in a finite body are in good agreement within .+-. 5% with the previous solutions. In transient state, the numerical values of thermal stress intensity factors for the Griffith crack are also in good agreement with the pervious solutions. In both steady and transient states, those for the symmetric lip cusp crack with the crack surface insulated or fixed to the constant temperature are calculates for various effective crack lengths, configuration parameters and uniform heat flow angles. The variations of the thermal boundary conditions of the crack surface have a effect on stress intensity factors. The signs on the values of thermal stress intensity factors can be changed in time variation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.320-320
• /
• 2014

Amorphous silicon alloy (a-Si) solar cells and modules have been receiving a great deal of attention as a low-cost alternate energy source for large-scale terrestrial applications. Key to the achievement of high-efficiency solar cells using the multi-junction approach is the development of high quality, low band-gap materials which can capture the low-energy photons of the solar spectrum. Several cell designs have been reported in the past where grading or buffer layers have been incorporated at the junction interface to reduce carrier recombination near the junction. We have investigated profiling the composition of the a-SiGe alloy throughout the bulk of the intrinsic material so as to have a built-in electrical field in a substantial portion of the intrinsic material. As a result, the band gap mismatch between a-Si:H and $a-Si_{1-x}Ge_x:H$ creates a barrier for carrier transport. Previous reports have proposed a graded band gap structure in the absorber layer not only effectively increases the short wavelength absorption near the p/i interface, but also enhances the hole transport near the i-n interface. Here, we modulated the GeH4 flow rate to control the band gap to be graded from 1.75 eV (a-Si:H) to 1.55 eV ($a-Si_{1-x}Ge_x:H$). The band structure in the absorber layer thus became like a U-shape in which the lowest band gap was located in the middle of the i-layer. Incorporation of this structure in the middle and top cell of the triple-cell configuration is expected to increase the conversion efficiency further.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.12
• /
• pp.1914-1924
• /
• 2016

In this paper, considering virtualized Evolved Packet Core(vEPC) network for 5G mobile network, we propose architecture for supporting Service Function Chaining(SFC) in 5G mobile network. Using SFC in 5G network, dynamic path configuration and providing network services based on subscriber and traffic information. SFC technology provides logical ordered set of network functions and delivers packet through providing logical path over the physical network. Based on the perspective of 5G core network in distributed manner, we design hierarchical SFC architecture to manage SFC for global path including vEPC and SGi-LAN network, and internal path between virtualized network functions in each cloud. In this paper, we define architecture and call flow for establishing data path using SFC. Finally, we design testbed architecture for real implementation based on open source software.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.50 no.1
• /
• pp.25-37
• /
• 2008

When livestock facilities in Korea have been changed larger and denser, rearing conditions have been getting worse and the productivity of animal production have been decreased. Especially in the cold season, the minimized ventilation has generally been operated to save energy cost in Korea resulting in very poor environmental condition and high mortality. While the stability, suitability, and uniformity of the rearing condition are the most important for high productivity, the ventilation configuration is the most important to improve the rearing condition seasonally. But, it is so difficult to analyze the internal air flow and the environmental factors by conducting only field experiment because the weather condition is very unpredictable and unstable as well as the structural specification can not be easily changed by the researchers considering cost and labor. Accordingly, an aerodynamic computer simulation was adopted to this study to overcome the weakness of conducting field experiment and study the aerodynamic itself. It has been supposed that the airflow is the main mechanism of heat, mass, and momentum transfers. To make the simulation model accurately and actually, simplified pig models were also developed. The accuracy of the CFD simulation model was enhanced by 4.4 % of errors compared with the data collected from field experiments. In this paper, using the verified CFD model, the CFD computed internal rearing condition of the mechanically ventilated pig house were analyzed quantitatively as well as qualitatively. Later, this developed model will be computed time-dependently to effectively analyze the seasonal ventilation efficiency more practically and extensively with tracer gas decay theory.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.285-285
• /
• 2011

EUVL (Extreme Ultra Violet Lithography) is one of competitive lithographic technologies for sub-30nm fabrication of nano-scale Si devices that can possibly replace the conventional photolithography used to make today's microcircuits. Among the core EUVL technologies, mask fabrication is of considerable importance since the use of new reflective optics having a completely different configuration compared to those of conventional photolithography. Therefore new materials and new mask fabrication process are required for high performance EUVL mask fabrication. This study investigated the etching properties of SnO2 (Tin Oxide) as a new absorber material for EUVL binary mask. The EUVL mask structure used for etching is SnO2 (absorber layer) / Ru (capping / etch stop layer) / Mo-Si multilayer (reflective layer) / Si (substrate). Since the Ru etch stop layer should not be etched, infinitely high selectivity of SnO2 layer to Ru ESL is required. To obtain infinitely high etch selectivity and very low LER (line edge roughness) values, etch parameters of gas flow ratio, top electrode power, dc self - bias voltage (Vdc), and etch time were varied in inductively coupled Cl2/Ar plasmas. For certain process window, infinitely high etch selectivity of SnO2 to Ru ESL could be obtained by optimizing the process parameters. Etch characteristics were measured by on scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) analyses. Detailed mechanisms for ultra-high etch selectivity will be discussed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.2
• /
• pp.1-10
• /
• 2005

An unstructured parallel overset mesh method has been developed for the simulation of unsteady flows around multiple bodies in relative motion. For this purpose, an efficient and robust search method is proposed for the unstructured grid system. A new data-structure is also proposed to handle the variable number of data on parallel sub-domain boundary. The interpolation boundary is defined for data communication between grid systems. An interpolation method to retain second-order spatial accuracy and to treat the points inside the neighboring solid bodies are also suggested. A single store separating from the Eglin/Pylon configuration is calculated and the result is compared with experimental data for validation. Simulation of unsteady flows around multiple bodies in relative motion is also performed.