• Proceedings of the Safety Management and Science Conference
• /
• 1999.11a
• /
• pp.53-72
• /
• 1999

IPQC system was introduced for the flight safety at the age of scientific safety management in the 1980s. In spite of performing this system, aircraft accidents caused by human factors, which were above 70% among all flight accident factors, have not been reduced. Accordingly, throughout this paper I analyzed the aircraft accident factors by means of a literature study and a pilot survey. Then, based on the notion of TQC(Total Quality Control), I hierarchically classified Individual Quality into Capacity Management, Safety Management, and General Management and did the low-ranked management factors as well. AHP (Analytic Hierarchy Process), one of the scientific management methods, was used for estimating the relative importance of Individual Quality Control factors and the heavy aircraft accident causes over the last 20 years were analyzed according to the flight ranks. Based on the comparative analysis of results derived above, an IPQC model as flight ranks is established. In short, according to this newly suggested model we can obtain the maximum flight safety with the preventive actions against aircraft accidents caused by human factors and by improving the operation effect under the reasonable pilot management.

• Journal of Aerospace System Engineering
• /
• v.15 no.4
• /
• pp.11-20
• /
• 2021

The estimation of hovering flight time of multicopters using the battery power propulsion system is important for the development and design of the aircraft and its operation. For a given operational weight, the maximum possible battery weight can be decided using both a conventional energy density method and a new Peukert law. In the present study, the hovering flight time is predicted using both methods. The specific data of multicopters in the published literatures were employed for the computation of the hovering flight time. The results were validated with the measured data. The effect of figure of merit of propeller, battery discharging process on the hovering flight time was evaluated, Finally, the effect of the battery cell and package connection types on the hovering time was investigated. It was found that the combination of serial battery cell connections and parallel package connection is the bast in the endurance maximization aspect. As the cell number increases in a package, the hovering flight time is increased. There exists the max. battery ratio for the given takeoff gross weight.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.31 no.2
• /
• pp.66-71
• /
• 2023

In the case of the Navy, if some of the co-pilots are included in the long-term promotion process due to the limited number of co-pilots, operational flight and administrative tasks will be added to the co-pilots not included in the rest of the Pilot in commander process. Therefore, to solve this problem, the co-pilot who has passed the PQS step-by-step process minimizes the personnel gap in the flight operation unit through a system that evaluates whether it is possible to perform its duties as a co-pilot through actual flight after entering the school. The advantage of the PQS course is that you can control flight plans on your own and minimize gaps in flight and ground work while carrying out the curriculum, but you can't focus on education or improve your skills due to irregular training flight cycles. Therefore, in this study, after collecting opinions on effective flight cycles through a survey of pilots of P-3C, the Navy's fixed-wing aircraft representative, we will analyze the association of aircraft volume performance by flight cycle to derive the optimal flight cycle of the P-3C pilot course.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.27 no.2
• /
• pp.132-137
• /
• 2017

Drone is currently used for wide application areas in our real life. Also it performs more important functions. We propose a method of drone operation system for the prevention of industrial disaster. In normal operation of drone system the drone monitors the industrial sites according to the planned flight path with acquiring the monitored images and send the image information to the server. The server analyzes and compares the images to DB information by calculating the similarity based on the threshold. Then the system decides whether the industrial sites has problems or not. If the abnormal condition is occurred, the drone change the flight path to abnormal flight path and keep monitoring the industrial sites with measuring the air status by sensors and sends all information to server system on the ground. If the emergency case is occurred, drone approaches the closest position of accident points and acquiring the all information and send them to server and 119 center.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.42 no.4
• /
• pp.69-75
• /
• 2019

Remotely Piloted Aircraft (RPA) controls as a type of unmanned aerial vehicle (drone) is growing rapidly and its flight controller stick disposition is required standardization. We should standardize RPA drone flight control disposition because the flight pilot of RPA is hard to be trained so the flight controller stick differences impairs safety and wastes time and effort of flight controller industry. So this study researches the on-going standardization of RPA drone flight control disposition in Korea and foreign countries. Also this paper analyzes and researches of expert about RPA drone flight controller function and application of flight control mode. I accomplished expert research about standardization plan of unmanned flight control mode and confirm the necessity. Nowadays mode1 and 2 are mostly used in Korea so I carried out preference investigation for two modes. There were 4 preferences choices of RPA drone control mode necessity (importance) and recommendation of standardization modes. They answered that necessity of standardization is important considering pilot training, flight safety and positive development of drone industry. The result of standardization mode preference is that they prefer mode 2 (drone maker 86%, training facilities and research facilities 58%, government bureau 60%). Overall preference result shows that mode 1 24%, mode 1&2 16%, mode 2 60%. So they preferred mode 2 by 60%. The differences between two modes are the direction of throttle and pitch. Direction of throttle and pitch operate opposite way. They prefer mode 2 because mode 2 has similarities of manned flight control mode. Significance of this study is that it showed the necessity of standardization and flight control preference in a quantitative way. It will help drone standardization in related industries and development direction near future.

• Journal of Advanced Navigation Technology
• /
• v.22 no.6
• /
• pp.537-544
• /
• 2018

A national comprehensive aviation test center is being constructed for the purpose of flight tests for development and modification of aircraft or flight inspections for the development of navaids. Flight testing is a high-risk task, so strict risk management processes are required prior to operation. In addition, since the flight test center is subject to the airdrome regulations under the current law, the introduction of the safety management system will enhance safety as usual in ordinary airports. The establishment of a safety management system based on ICAO criteria is an optimal means of ensuring safe and effective operation of the test center and may mitigate the risks that may arise during flight testing. This paper focuses on risk assessment and mitigation required for safety management at the flight test center. We conducted risk assessments on the flight hazards identified in the previous study. Then the high risk group of hazards were selected and risk mitigation techniques such as avoidance, reduction, acceptance, and control were applied.

• Journal of Advanced Navigation Technology
• /
• v.25 no.6
• /
• pp.466-475
• /
• 2021

Airport-related laws restrict the installation of lights that obstruct the identification of airport lights or cause glare to pilots and controllers around the airport. However, with regard to the glare that lights give to the pilot or controller, it is only judged whether there is a limit based on a qualitative judgment, and a quantitative review has not been made. Therefore, in this study, visual disturbances that may occur to pilots and controllers due to large lighting facilities around airports during nighttime flight operation were quantitatively calculated and confirmed through disability glare, object recognition, and identification obstruction. And based on this study, it was suggested to supplement the related system to prevent the visual impairment of pilots and controllers caused by lighting facilities.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.1
• /
• pp.120-131
• /
• 2016

The full results of troubleshooting process related to the flight control system of a tilt-rotor type UAV in the flight tests are described. Flight tests were conducted in helicopter, conversion, and airplane modes. The vehicle was flown using automatic functions, which include speed-hold, altitude-hold, heading-hold, guidance modes, as well as automatic take-off and landing. Many unexpected problems occurred during the envelope expansion tests which were mostly under those automatic functions. The anomalies in helicopter mode include vortex ring state (VRS), long delay in the automatic take-off, and the initial overshoot in the automatic landing. In contrast, the anomalies in conversion mode are untrimmed AOS oscillation and the calibration errors of the air data sensors. The problems of low damping in rotor speed and roll rate responses are found in airplane mode. Once all of the known problems had been solved, the vehicle in airplane mode gradually reached the maximum design speed of 440km/h at the operation altitude of 3km. This paper also presents a comprehensive detailing of the control systems of the tilt-rotor unmanned air vehicle (UAV).

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.22 no.2
• /
• pp.53-59
• /
• 2014

Simultaneous parallel approaches in all weather conditions should be applied to manage efficiently increasing volume of air traffic flow and solve the problem of delayed arrivals. But All of the airports which have closely-spaced parallel-runways in Korea don't meet the interval-standards for IFR parallel approaches. In that regard, more accurate and safer System should be applied for the Korean airports. GNSS was adopted as an international standard of the next-generation navigation system and many studies and master plans have been activated by stages in Korea. In this paper, the current state of the domestic airports will be analyzed focusing on the interval of parallel runways and future specification of both flight operation system and air-side management will be recommended.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.23 no.4
• /
• pp.22-29
• /
• 2015

Quadrotor is widely used in variable application nowadays. Due to its inherent unstable characteristics, control system to augment the stability is essential for quadrotor operation. To design control system and verify its performance through simulation, accurate dynamic model is required. Quadrotor dynamic model is simply compared with conventional rotorcraft such as helicopter. However, the accurate dynamic model of quadrotor is not easy to develop because of the highly correlated aerodynamic effect of each rotor. In this paper, quadrotor dynamic model is identified from the flight data using frequency domain approach. Flight test of quadrotor is performed in closed loop configuration with stability augmentation system included. Frequency sweep input is applied in each of lateral, longitudinal, yaw and heave axis separately. The bare dynamic model is identified from the flight data of quadrotor responses and thrust measurement through Pulse Width Modulation(PWM) data. The frequency responses of identified model match well with those of flight data, and time responses of identified model for doublet input in each axis are also shown to agree with flight data.