• Resources Recycling
• /
• v.15 no.3 s.71
• /
• pp.66-73
• /
• 2006

Continuous column adsorption experiments have been conducted fur artificial and actual wastewater which containing $Ni^{2+}$ by using manganese nodule as an adsorbent for the purpose of wastewater treatment along with an increased $Ni^{2+}$ recovery in the refining of manganese nodule. The adsorption features of $Ni^{2+}$ artificial wastewater were examined by taking the height of fixed bed, influent flow rate, and the initial concentration of adsorbate as the influential parameters. The adsorption capacity of manganese nodule and the rate constant for $Ni^{2+}$ adsorption were estimated employing Bohart-Adams equation. In addition, the variation of the adsorbed amount of adsorbate for each column according to the influent flow rate and the initial concentration of adsorbate was investigated based on the breakthrough curves fur each column. For serially connected columns, the adsorbed amount of $Ni^{2+}$ for each column was observed to increase gradually as the adsorption proceeded from the initial column to the final column. The variation of the breakthrough curve for actual wastewater with the height of fixed bed was not so significant as that for artificial wastewater, which was considered to be due to the high concentration of $Ni^{2+}$ in actual wastewater. Regarding the effect of the particle size of manganese nodule on adsorption, the adsorbed amount of adsorbate was found to somewhat increase as the particle size became smaller.

• Journal of Bio-Environment Control
• /
• v.16 no.3
• /
• pp.217-221
• /
• 2007

To provide the basic data essential for developing varieties of broad-leaved tree, the study investigated the utmost growth requirement for the growth characteristic and biomass production in accordance with planting density of Styrax obassia. The planting density of seedling can be a significant factor in contributing growth of seedling for tree growing in general. While growth of tree according to $1m^2$ planting density of Styrax obassia showed an excellent growth in tree height and the root collar diameter from $49no./m^2$, those low planting density showed decreased tendency with tree height growth while increasing the root collar diameter growth. As similar to the growth characteristic, the biomass production showed significant and statistic difference in $49no./m^2$, showing high volume of biomass production which is $3.12{\pm}0.80g$ compare to other processing section and high figure with T/R ratio which is 1.59. The special trait of photosynthetic also showed relatively high photosynthetic rate in $49no./m^2\;and\;64no./m^2$ of Styrax obassia and as the density increase, photosynthetic efficiency decreased. The plant showed stable and physiological planting pattern, displaying the best photosynthetic rate, which was the final metabolism through reserving proper space in the growth and development environment condition. This obstacle of required space essential for growth substantially deteriorated planting and ultimately, it demonstrated lower tendency of photosynthetic rate, which is the highest level of metabolism.

• Journal of Korean Society of Transportation
• /
• v.23 no.5 s.83
• /
• pp.123-134
• /
• 2005

This research aims at developing a new method which can replace the existing method. known as the quality factor(Q factor) method by an L-R-C test for use in the performance test of inductive loop detectors(ILD) being installed and maintained. In this study, a sensor to detect a magnetic field in terms of frequency and intensity, a method to collect field data, the method of analysis, and the method of diagnosis were developed. An automatic diagnosis system which was developed to overcome those drawbacks has the following features : First, field data is collected automatically by a test vehicle equipped with magnetic field sensors that is running can be said to along the roadway and. thus, the new system completely overcome the roadway and, thus, the new system can be said to completely overcome the inefficiency of the existing method second, since the magnetic fold generated from the ILD is the final output of the whole system of ILD, the existing problem has been solved. third. since each of the detection area by height is collected by the magnetic sensors installed by height. a basic for the identification of the vehicle types to be detectable and the setting of adjustment factors has been made. For the automatic diagnosis system developed during in this study, a reliability test was carried out by comparing vehicle times of ILD installed ideally.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.2
• /
• pp.81-91
• /
• 2002

Dental implant systems have shown many post-surgical problems and One of the most frequent problem is screw loosening. To reduce screw loosening, a number of methods have been tried and recently fundamental modification of fixture-abutment connection structure was developed and used the most frequently. Former implant system structure, such as Br${\aa}$nemark, had external hex with the height of 0.7 mm and later, fixture with external hex of 1.0 mm height and internal hex structure were developed. In addition, the method of morse taper application was introduced to reduce screw loosening. In this study, the level of screw loosening of each implant systems was compared based on the vibration loosening measurement of abutment screw of each implant systems. Analysis of measured value was performed using 3 kinds of methods, (i) Percentage of average of initial 3 times loosening-torque value(initial loosening value) to tightening-torque of 30 Ncm, (ii) Percentage of loosening-torque value after 200 N strength loaded(experimental value) to initial loosening value and (iii) Percentage of experimental value to 30 Ncm of tightening-torque. Each result of analyses shows the value of initial loosening, loosening by repetitive load and final loosening level. The results of this study were as follows. (1) Percentage of initial loosening value to tightening-torque was increased in order of 0.7 mm external hex, 1.0 mm external hex, internal hex and internal taper and all values between each groups showed statistical significance (p<0.05). (2) Percentage of experimental value to initial loosening value was increased in order of internal hex, 0.7 mm external hex, 1.0 mm external hex and internal taper. Value of internal taper showed significant difference with that of 0.7 mm external hex and internal hex (p<0.05). (3) Percentage of experimental value to tightening torque was increased in order of 0.7 mm external hex, 1.0 mm external hex, internal hex and internal taper. Values of all groups showed statistical significance (p<0.05) except between the groups of 1.0 mm external hex and internal hex. Based on those results, there was no significant difference of loosening-torque by repetitive loading except internal taper. It is supposed that implant system with high resistant capability against initial loosening could be recommended for clinical use. In addition, in case of single implant restoration, 1.0 mm external hex or internal hex could be recommended rather than 0.7 mm external hex, and the use of internal taper would be the most useful way to reduce screw loosening.

• Smart Structures and Systems
• /
• v.4 no.2
• /
• pp.221-232
• /
• 2008

This paper represents the final results of a research program sponsored by the European Commission through project WIND-CHIME ($\underline{W}$ide Range Non-$\underline{IN}$trusive $\underline{D}$evices toward $\underline{C}$onservation of $\underline{HI}$storical Monuments in the $\underline{ME}$diterranean Area), in which the possibility of using advanced seismic protection technologies to preserve historical monuments in the Mediterranean area is investigated. In the current research, the dynamic characteristics of two outstanding Mamluk-Style minarets, which similar minarets were reported to experience extensive damage during Dahshur 1992 earthquake, are investigated. The first minaret is the Qusun minaret (1337 A.D, 736 Hijri Date (H.D)) located in El-Suyuti cemetery on the southern side of the Salah El-Din citadel. The minaret is currently separated from the surrounding building and is directly resting on the ground (no vaults underneath). The total height of the minaret is 40.28 meters with a base rectangular shaft of about 5.42 ${\times}$ 5.20 m. The second minaret is the southern minaret of Al-Sultaniya (1340 A.D, 739 H.D). It is located about 30.0 meters from Qusun minaret, and it is now standing alone but it seems that it used to be attached to a huge unidentified structure. The style of the minaret and its size attribute it to the first half of the fourteenth century. The minaret total height is 36.69 meters and has a 4.48 ${\times}$ 4.48 m rectangular base. Field investigations were conducted to obtain: (a) geometrical description of the minarets, (b) material properties of the minarets' stones, and (c) soil conditions at the minarets' location. Ambient vibration tests were performed to determine the modal parameters of the minarets such as natural frequencies and mode shapes. A $1/16^{th}$ scale model of Qusun minaret was constructed at Cairo University Concrete Research Laboratory and tested under free vibration with and without SMA wire dampers. The contribution of SMA wire dampers to the structural damping coefficient was evaluated under different vertical loads and vibration amplitudes. Experimental results were used along with the field investigation data to develop a realistic 3-D finite element model that can be used for seismic risk evaluation of the minarets. Examining the updated finite element models under different seismic excitations indicated the vulnerability of such structures to earthquakes with medium to high a/v ratio. The use of SMA wire dampers was found feasible for reducing the seismic risk for this type of structures.

• Clean Technology
• /
• v.20 no.3
• /
• pp.321-329
• /
• 2014

In this study, Indonesia low rank coal, which has moisture content of around 26%, is dried less than 5% by using a laboratory-scale (batch type) steam fluidized-bed dryer in order to produce the low-moisture, high rank coal. Normally, CCS (carbon capture and storage) process discharges $CO_2$ and steam mixture gas around $100-150^{\circ}C$ of temperature after regeneration reactor. The final purpose of this research is to dry low rank coal by using the outlet gas of CCS process. At this stage, steam is used as heat source for drying through the heat exchanger and $CO_2$ is used as fluidizing gas to the dryer. The experimental variables were the steam flow rate ranging from 0.3 to 1.1 kg/hr, steam temperature ranging from 100 to $130^{\circ}C$, and bed height ranging from 9 to 25 cm. The characteristics of the coal, before and after drying, were analyzed by a proximate analysis, the heating value analysis and particle size analysis. In summary, the drying rate of low rank coal was increased as steam flow rate and steam temperature increased and increased as bed height decreased.

• Archives of Reconstructive Microsurgery
• /
• v.20 no.1
• /
• pp.43-50
• /
• 2011

Lunate revascularization with the vascularized bone grafts is a current concept in the treatment of Kienbo${\ddot{o}}$ck disease. The aim of this study is to present our experience and preliminary results of the treatment using the fourth extensor compartment artery (4 ECA) vascularized bone graft for Kienbo${\ddot{o}}$ck disease. Between May 2009 and June 2010, five patients (3 men and 2 women) with Kienbo${\ddot{o}}$ck disease were treated with 4 ECA vascularized bone grafts. The mean age was 32.8 years and mean follow-up time was 13 months. The patients were composed of two patients in stage II and three patients in stage IIIa according to Lichtman's classification. Modified Mayo wrist score including pain, grip strength, range of motion and functional status and radiographic parameters such as carpal height ratio and radioscaphoid angle were evaluated at a final follow-up. Pain was markedly diminished and modified Mayo wrist score was 82 at last follow up period. There were no or little changes in carpal height ratio and radioscaphoid angle. All patients showed satisfactory bony union and no further lunate collapse on follow-up radiographs. The 4 ECA vascularized bone graft is a reliable alternative procedures among revascularization procedures for treatment of Kienbo${\ddot{o}}$ck's disease. It is less invasive and has low risk of kinking of pedicle compared to the 4+5 ECA vascularized bone graft. However, long term follow-up and MRI evaluation at follow up period should be needed for the future.

• Journal of Korean Society for Geospatial Information Science
• /
• v.21 no.2
• /
• pp.27-34
• /
• 2013

Due to the increased interest in global warming, interest in forest resources aimed towards reducing greenhouse gases have subsequently increased. Thus far, data related to forest resources have been obtained, through the employment of aerial photographs or satellite images, by means of plotting. However, the use of imaging data is disadvantageous; merely, due to the fact that recorded measurements such as the height of trees, in dense forest areas, lack accuracy. Within such context, the authors of this study have presented a method of data processing in which an individual tree is isolated within forested areas through the use of LIDAR data and ortho-images. Such isolation resulted in the provision of more efficient and accurate data in regards to the height of trees. As for the data processing of LIDAR, the authors have generated a normalized digital surface model to extract tree points via local maxima filtering, and have additionally, with motives to extract forest areas, applied object oriented image classifications to the processing of data using ortho-images. The final tree point was then given a figure derived from the combination of LIDAR and ortho-images results. Based from an experiment conducted in the Yongin area, the authors have analyzed the merits and demerits of methods that either employ LIDAR data or ortho-images and have thereby obtained information of individual trees within forested areas by combining the two data; thus verifying the efficiency of the above presented method.

• Journal of Fashion Business
• /
• v.11 no.6
• /
• pp.101-114
• /
• 2007

This research aimed to identify the differences, in terms of the pattern, of using wool and jersey for designing jackets and to provide a theorized solution. The object of this study is development of women's tailored jacket pattern by the traits of fabrics with fabrics those are generally used to develop the power of manufacturing technique about fit of jacket. Basic bodies prototype, graphics of sleeves prototype and graphics of jacket pattern those a clothing company at present(on&on, a brand of Beaucre Merchandising Co.,Ltd) is using were used as basics of tailored jacket pattern. Three kinds of fabric(wool, polyester, jersey) were chosen, we made jackets in the same manufacturing process of the clothing company, modified and made up for the weak points and then we compared and analyzed differences of pattern by the traits of fabrics, the results are as follows: 1) We drafted basic tailored style jacket pattern, made a jacket with wool fabric, made wearing experiment, modified and made up for the weak points by the trend, then developed JacketⅠ for study; 2) With JacketⅠ for study as the basic, we made a jacket with polyester fabric, made wearing experiment, modified and made up for the weak points, then developed Jacket II for study; 3) With JacketⅠ for study as the basic, we made a jacket with jersey fabric, made wearing experiment, modified and made up for the weak points, then developed Jacket III for study; 4) We presented final degree of polymerization of pattern with Jacket I II III for study; 5) We compared and analyzed the differences of pattern with the degree of polymerization of pattern with Jacket I(Wool) for study and Jacket II(Polyester), there was no change of size overall except extra amount which happens because of the trait of the fabric in 20 items of body format pattern, there were differences of size in 3 items(height of a sleeve, width of a sleeve, length of a sleeve) among 5 items of sleeves pattern; 6) We compared and analyzed the differences of pattern with the degree of polymerization of pattern with Jacket I(Wool) for study and Jacket III(Jersey) for study, there were differences of size by the kinds of fabric in 11 items(neck point to shoulder point length, Bishoulder point length, back interscye length, front interscye length, armhole circumference, depth of armhole, chest circumference, bust circumference, waist circumference, hip circumference, waist dart) among 20 items of body format pattern, there were differences of size by the kinds of fabric in 5 items(height of a sleeve, circumference of a sleeve, width of a sleeve, length of a sleeve, width of bottom of a sleeve) among 5 items of sleeves pattern.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.57-62
• /
• 2006

Busan New Port, under construction aiming for the hub of Northeast Asia and Partly in operation, had damaged up to 48 billion Won due to Typhoon 'maemi' in 2003. The present criteria of domestic harbor design only describes about the critical wave height with respect to the size of vessel for harbor tranquility. The berth operation ratio which represents the annual available berthing days is depending on the efficiency of cargo handling work and this depends on the motion of the moored vessel due to the wave action and the characteristics of cargo gears. The motion of moored vessel might be related not only to the wave height but also to wave period. Furthermore, the berth operation ratio relies on external forces such as currents and winds, including the characteristics of mooring system and the specification of the moored vessel. In this study we only deal with berth operation ratio in normal sea state, considering wave and current by measured data and numerical calculation. Especially we tried to evaluate the berth operation ratio for each berth adopting the variation of dredging and reclamation plan and the change of wave environment during the process of the new port construction. For better understanding and analysis of wave transformation process, we applied the steady state spectral wave model and extended mild-slope wave model to the related site. This study summarizes comparisons of harbor responses predicted by two numerical predictions obtained at Busan New port site. Field and numerical model analysis was conducted for the original port plan and the final corrected plan.