• Journal of Industrial Convergence
• /
• v.20 no.10
• /
• pp.33-38
• /
• 2022

In this paper, a simple method of forming a solution-based carbon nanotube (CNT) for use as a conductive material for electronic devices was studied. The CNT thin film coating was performed on the glass by applying the spin coating method and the argon atmospheric pressure plasma process. In order to observe changes in electrical and physical properties according to the number of coatings, samples formed in the same manner from times 1 to 5 were prepared, and surface shape, reflectance, transmittance, absorbance, and sheet resistance were measured for each sample. As the number of coatings increased, the transmittance decreased, and the reflectance and absorptivity increased in the entire measurement wavelength range. Also, as the wavelength decreases, the transmittance decreases, and the reflectance and absorption increase. In the case of electrical properties, it was confirmed that the conductivity was significantly improved when the second coating was applied. In conclusion, in order to replace CNT with a transparent electrode, it is necessary to consider the number of coatings in consideration of reflectivity and electrical conductivity together, and it can be seen that 2 times is optimal.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.6
• /
• pp.503-516
• /
• 2021

Autonomous fire detection and suppression system requires advanced technology for complex detection technology and injection/control technology for accurate hitting by fire location. Also, foam spraying should be included to respond to oil fires. However, when a single spray monitor is used in common, water and foam spray properties appear different, so for accurate fire suppression, research on the spray trajectory and distance will be required. In this study, experimental studies and numerical analysis studies were combined to analyze the foam spray characteristics through the spray monitor developed for the establishment of an autonomous fire extinguishing system. For flow analysis of foam injection, modeling was performed using OpenFOAM analysis software, and the commonly used foaming agent (Aqueous Film-Forming Foam) was applied for foam properties. The injection distance analysis was performed according to the injection pressure and the injection angle according to the form of the foam, and at the same time, the results were verified and presented through the injection experiment.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.49 no.2
• /
• pp.140-148
• /
• 2022

This study aimed to evaluate the effect of silver diamine fluoride (SDF) and potassium iodide (KI) on the formation of cariogenic biofilm and surface roughness in vitro. A total of 48 bovine dentin specimens with artificially induced caries were prepared and divided into 3 groups of 16: untreated control, SDF-treated, and SDF-treated followed by KI (SDFKI). Ten specimens from each group were used to observe microbial adhesion. Multispecies cariogenic biofilms including Streptococcus mutans, Lactobacillus casei, and Candida albicans were cultured on the specimens. Microbes were cultured for 24 hours, and the colony-forming unit was calculated. The remaining specimens were observed by atomic force microscope and scanning electron microscope (SEM). The number of bacteria was significantly lower in the SDF and SDFKI groups. KI did not inhibit the antibacterial activity of SDF significantly. SEM images showed particles generated after SDF and SDFKI application were deposited on the dentin, but there was no significant difference in surface roughness between the 3 groups. This study confirmed that SDF and SDFKI application did not have a significant effect on the surface roughness of dentin, but effectively inhibited the formation of the early cariogenic bacterial film after 24 hours compared to the control.

• Cartoon and Animation Studies
• /
• s.51
• /
• pp.293-319
• /
• 2018

Thanks to the advancement of the related technologies and equipment, today's video contents like movies, animations and soap operas are rapidly expanding their expressible cinematic imagination area. In order to fulfill the elevated visual expectations of audiences and realize exciting storytelling and fantastic world, the fusion of different techniques is actively used, and the reality for visual effects and image synthesis is increasing more and more. Accordingly, recent VFX-oriented movies using CG have a much more complicated production process than before. Therefore, the importance of Pre-visualization, aka Pre-vis is becoming bigger in the planning process for sophisticated design. Pre-vis means that the advance visualization for stories or directing ideas in the planning process before starting production of movies or animations. 3D animated Pre-visualization realizing directors' abstract and ambiguous ideas in 3 dimensional environment in advance is, as a powerful means for visual storytelling, briskly used focusing on the VFX film industry on which the present CG is broadly used, and the role of Pre-vis throughout productions has increased compared to the past. The studies, however, on the role and utility of Pre-vis are not enough. Therefore, this study was conducted on the role of Pre-vis used for present VFX movie productions using the examples of 3D animated Pre-visualization production in which the researcher of this study participated. In this study, the role of the Pre-vis that is subdivided presently, is divided into and 3D animatics and their each role is analyzed with the example images. Through this, the characteristics that Pre-vis should have are clarified and the concept of the advantages and utility led by the use of Pre-vis in productions is strengthened. The goal of this study is to induce active uses of Pre-vis throughout productions after forming consensus about the various roles of Pre-vis and their utility.

• Applied Microscopy
• /
• v.37 no.1
• /
• pp.23-33
• /
• 2007

The lacrimal gland are compound tubule-acinar glands. The main lacrimal function is the production of the aqueous layer, the thickest and major constituent of the precorneal tear film. The lacrimal gland also has an important function in the defense system of the ocular surface, forming a part of the conjunctival-associated hymphoid tissue. The ultrastructural characteristics of the lacrimal gland of the rabbit were described. The lacrimal tissues of rabbits were processed through the conventional techniques for transmission electron microscopy. The secretory portions consisted of three cell types: 1. Serous cells with electron dense secretory granules. 2. Seromucous cells containing variable moderately electron dense secretory granules with flocculent material. 3. Mucous rolls containing mucous secretory granules. The serous cells were situated at the basal portion of acini, and they contained electron dense granules of variable densities and sizes. The seromucous cells contained a few protein secretory granules and more mucous secretory granules. The mucous cells contained even fewer protein secretory granules and exclusively mucous secretory granules. The epithelium of the intralobular ducts showed secretory granules, junctional complexes, and large basolateral intercellular spaces with lateral folds. These study might be helpful in determining inter-relationships, similarities and differences among the orbital glands of various physiological or pathological conditions.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.12
• /
• pp.1249-1256
• /
• 2005

This study was performed to investigate the efficiency of the corrosion prevention in the simulated distribution system using CCPP(Calcium Carbonate Precipitation Potential) as the anti-corrosive index by adjusting pH, total dissolved solids, alkalinity and calcium hardness in the water treatment pilot process. The materials of the simulated distribution system(SDS) were equiped with same materials of real field water distribution system. CCPP concentrations controlled by $Ca(OH)_2$, $CO_2$ gas and $Na_2CO_3$ in the simulated distribution system and uncontrolled by the chemicals in the general water distribution system were average 0.61 mg/L and -7.77 mg/L. The concentrations of heavy metals like Fe, Zn, Cu ions in effluent water of the simulated distribution system controlled with water quality were decreased rather than the general water distribution system uncontrolled with water quality. In simulated distribution system(SDS), corrosion prevention film formed by CCPP control was observed that scale was come into forming six months later and it was formed into density as time goes on. We were analyzed XRD(X-ray diffraction) for investigating component of crystal compounds and structure for galvanized steel pipe(15 mm). Finding on analysis, scale was compounded to $Zn_4CO_3(OH)_6{\cdot}H_2O$ (Zinc Carbonate Hydroxide Hydrate) after ten months late, and it was compounded on $CaCO_3$(Calcium Carbonate) and $ZnCO_3$(Smithsonite) after nineteen months later.

• Journal of the Korean Geographical Society
• /
• v.42 no.4
• /
• pp.526-539
• /
• 2007

The purpose of this study is to investigate the influence of the Korean Wave on Chinese tourism to South Korea through a behavioral analysis of Chinese tourists in the general group package tours. China suppressed the needs of the Chinese people's geographical movement and imposed restrictions on information about the outside world with the use of a policy of "closure" for a long time. But since reforms and open-door policies were introduced in China, especially in the context of relaxation of control policies over Chinese outbound tourism after the mid-1990's, more and more Chinese make trips abroad including visits to South Korea. In this situation, the recent Korean Wave(especially, drama/film) describes the Korean national image by forming a bridge between fiction and reality and plays a pivotal role in broadening or reconstructing the geographical imagination of the Chinese people who have been historically isolated from the outside world. Although Chinese have imagined the Korean nationscape on the basis of geopolitical or economic factors in the past, they have currently broadened or reconstructed their geographical imagination to include socio-cultural factors related closely to the Korean way of life due to the recent Korean Wave. This newly constructed geographical imagination led by the Korean Wave functions as an important pulling factor in Chinese destination choices, affecting Chinese tourists' motivation formation and the recommendation of main attractions. The more influential the Korean Wave is on their destination choice, the more the respondents select the cultural factors in both their motivation for tourism to South Korea and their recommendations of tourism attractions to other people. Through the analysis results of both satisfaction and intention to revisit, the more influential the Korean Wave is on their destination choice, the higher is the degree of both satisfaction and intention to revisit. In other words, although Chinese tourism to South Korea is chiefly in the general group package tours, Chinese tourists who are influenced by Korean Wave on their destination choice have more attachment to(or affection for) Korea as a tourism destination. This result suggests that the Korean Wave affects qualitative change - that is, change of attitude - as well as quantitative change in Chinese demand for tourism to South Korea.

• Journal of Sensor Science and Technology
• /
• v.11 no.1
• /
• pp.9-17
• /
• 2002

The forming conditions of X-ray storage phosrhors $BaFBr_{1-x}I_x:Eu^{2+}$, $Na^+$ have been investigated, and measured the PSL emission spectra and its intensity, fading characteristics and does dependence of the prepared phosphors. These characteristics were compared with those of commercial image plate (ST-III) obtained from Fuji Photo Film Co. The optimal preparing conditions of $BaFBr_{1-x}I_x:Eu^{2+}$, $Na^+$ Phosphor were 0.5 mol% of $EuF_3$, 4.0 mol% of NaF and composition ratio x=0.3, and the sintering temperature were $950^{\circ}C$ in $H_2$ atmosphere. When the composition ratio x was equal to 0, the spectral range of the luminescence of $BaFBr_{1-x}I_x:Eu^{2+}$, $Na^+$ phosphor was $365{\sim}420\;nm$, and its maximum luminescence intensity appeared at 390 nm. When composition ratio x was not equal to 0, the wavelength ranges and peak of the spectra were shifted to the longer wavelength with the growth of composition ratio x. A good linearity was shown between the PSL intensity and X-ray irradiation dose. The phosphor sample with x=0.3 exhibited better fading characteristics than that of other $BaFBr_{1-x}I_x:Eu^{2+}$ phosphor samples, and the fading characteristics of the PSL intensity at room temperature were shown poorer with increasing $I^-$ ion concentration. The lattice constant of the phosphor becomes larger with increasing the $I^-$ ion concentration.

• Clean Technology
• /
• v.29 no.4
• /
• pp.255-261
• /
• 2023

Power semiconductors are semiconductors used for power conversion, transformation, distribution, and control. Recently, the global demand for high-voltage power semiconductors is increasing across various industrial fields, and optimization research on high-voltage IGBT components is urgently needed in these industries. For high-voltage IGBT development, setting the resistance value of the wafer and optimizing key unit processes are major variables in the electrical characteristics of the finished chip. Furthermore, the securing process and optimization of the technology to support high breakdown voltage is also important. Etching is a process of transferring the pattern of the mask circuit in the photolithography process to the wafer and removing unnecessary parts at the bottom of the photoresist film. Ion implantation is a process of injecting impurities along with thermal diffusion technology into the wafer substrate during the semiconductor manufacturing process. This process helps achieve a certain conductivity. In this study, dry etching and wet etching were controlled during field ring etching, which is an important process for forming a ring structure that supports the 3.3 kV breakdown voltage of IGBT, in order to analyze four conditions and form a stable body junction depth to secure the breakdown voltage. The field ring ion implantation process was optimized based on the TEG design by dividing it into four conditions. The wet etching 1-step method was advantageous in terms of process and work efficiency, and the ring pattern ion implantation conditions showed a doping concentration of 9.0E13 and an energy of 120 keV. The p-ion implantation conditions were optimized at a doping concentration of 6.5E13 and an energy of 80 keV, and the p+ ion implantation conditions were optimized at a doping concentration of 3.0E15 and an energy of 160 keV.