• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.6
• /
• pp.15-23
• /
• 2011

Driving directly in front of the driver of a vehicle driving in front of the vehicle and it is commonly known is affected. Responding to the car in front of the driver and the vehicle in front, and these follow the model is known as Three-Car-Following Model. Platoon vehicles to follow behind the driver's visibility is affected by the a tinted vehicle, and Parameters of the model is estimated to be affected also. In this study, in Three-Car-Followng Model parameters were estimated. and the parameter values differ about whether and how analysis was performed by the level of Visible Light Transmission Percentage. RTK GPS receiving data through field experiment analyzed based on sensitivity of three car by Visible Light Transmission Percentage and ${\gamma}$. And With statistical verification of driving directly in front of the driver in front of the vehicle and that the moving vehicle is influenced also confirmed. Also Visible Light Transmission Percentage is lowered, the vehicle in front of the driver's behavior showed sensitive reactions. In the further need to research for influence analysis of traffic flow capacity by the level of VLT.

• Journal of the Korean Magnetics Society
• /
• v.14 no.4
• /
• pp.149-161
• /
• 2004

The fusion of nano technology and information technology is essential to sustain the present growth rate and to induce new industry in this ever-growing information age. Considering Korean industry whose competitiveness lies heavily on information related technologies, this field will be inevitable for future. Nano materials can be described as novel materials whose size of elemental structure has been engineered at the nanometer scale. Materials in the nanometer size range exhibit fundamentally new behavior, as their size falls below the critical length scale associated with any given property. " Bottom-up' techniques involve manipulating individual atoms and molecules. Bottom-up process usually implies controlled or directed self assembly of atoms and molecules into nano structures. It resembles more closely the processes of biology and chemistry, where atoms and molecules come together to create structures such as crystals or living cells. Nano scale sensors are included in the electronics area since the diverse sensing mechanisms are often housed on a semiconductor substrate and usually give rise to an electronic signal. The application of nano technology to the chemical sensors should allow improvements in functionality such as gas sensing. In this presentation, we will discuss about the nano scale information materials and devices fabricated by using the organic/inorganic nano templates.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.4
• /
• pp.281-288
• /
• 2014

As a gas explosion is the most fatal accident in shipbuilding and offshore plant industries, all safety critical elements on the topside of offshore platforms should retain their integrity against blast pressure. Even though many efforts have been devoted to develop blast-resistant design methods in the offshore engineering field, there still remain several issues needed to be carefully investigated. From a procedure for calculation of explosion design pressure, impulse of a design pressure model having completely positive side only is determined by the absolute area of each obtained transient pressure response through the CFD analysis. The negative pressure phase in a general gas explosion, however, is often quite considerable unlike gaseous detonation or TNT explosion. The main objective of this study is to thoroughly examine the effect of the negative pressure phase on structural behavior. A blast wall for specific FPSO topside is selected to analyze structural response under the blast pressure. Because the blast wall is considered an essential structure for blast-resistant design. Pressure time history data were obtained by explosion simulations using FLACS, and the nonlinear transient finite element analyses were performed using LS-DYNA.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.559-563
• /
• 2015

Monitor of All-sky X-ray Image (MAXI) is a Japanese X-ray all-sky surveyer mounted on the International Space Station (ISS). It has been scanning the whole sky since 2009 during every 92-minute ISS rotation. X-ray transients are quickly found by the real-time nova-search program. As a result, MAXI has issued 133 Astronomer's Telegrams and 44 Gamma-ray burst Coordinated Networks so far. MAXI has discovered six new black holes (BH) in 4.5 years. Long-term behaviors of the MAXI BHs can be classified into two types by their outbursts; a fast-rise exponential-decay type and a fast-rise flat-top one. The slit camera is suitable for accumulating data over a long time. MAXI issued a 37-month catalog containing 500 sources above a ~0.6 mCrab detection limit at 4-10 keV in the region ${\mid}{b}{\mid}$ > $10^{\circ}$. The SSC instrument utilizing an X-ray CCD has detected diffuse soft X-rays extending over a large solid angle, such as the Cygnus super bubble. MAXI/SSC has also detcted a Ne emission line from the rapid soft X-ray nova MAXI J0158-744. The overall shapes of outbursts in Be X-ray binaries (BeXRB) are precisely observed with MAXI/GSC. BeXRB have two kinds of outbursts, a normal outburst and a giant one. The peak dates of the subsequent giant outbursts of A0535+26 repeated with a different period than the orbital one. The Be stellar disk is considered to either have a precession motion or a distorted shape. The long-term behaviors of low-mass X-ray binaries (LMXB) containing weakly magnetized neutron stars are investigated. Transient LMXBs (Aql X-1 and 4U 1608-52) repeated outbursts every 200-1000 days, which is understood by the limit-cycle of hydrogen ionization states in the outer accretion disk. A third state (very dim state) in Aql X-1 and 4U 1608-52 was interpreted as the propeller effect in the unified picture of LMXB. Cir X-1 is a peculiar source in the sense that its long-term behavior is not like typical LMXBs. The luminosity sometimes decreases suddenly at periastron. It might be explained by the stripping of the outer accretion disk by a clumpy stellar wind. MAXI observed 64 large flares from 22 active stars (RS CVns, dMe stars, Argol types, young stellar objects) over 4 years. The total energies are $10^{34}-10^{36}$ erg $s^{-1}$. Since MAXI can measure the spectrum (temperature and emission measure), we can estimate the size of the plasma and the magnetic fields. The size sometimes exceeds the size of the star. The magnetic field is in the range of 10-100 gauss, which is a typical value for solar flares.

• Journal of Periodontal and Implant Science
• /
• v.36 no.2
• /
• pp.531-554
• /
• 2006

Oral implants must fulfill certain criteria arising from special demands of function, which include biocompatibility, adequate mechanical strength, optimum soft and hard tissue integration, and transmission of functional forces to bone within physiological limits. And one of the critical elements influencing the long-term uncompromise functioning of oral implants is load distribution at the implant- bone interface, Factors that affect the load transfer at the bone-implant interface include the type of loading, material properties of the implant and prosthesis, implant geometry, surface structure, quality and quantity of the surrounding bone, and nature of the bone-implant interface. To understand the biomechanical behavior of dental implants, validation of stress and strain measurements is required. The finite element analysis (FEA) has been applied to the dental implant field to predict stress distribution patterns in the implant-bone interface by comparison of various implant designs. This method offers the advantage of solving complex structural problems by dividing them into smaller and simpler interrelated sections by using mathematical techniques. The purpose of this study was to evaluate the stresses induced around the implants in bone using FEA, A 3D FEA computer software (SOLIDWORKS 2004, DASSO SYSTEM, France) was used for the analysis of clinical simulations. Two types (external and internal) of implants of 4.1 mm diameter, 12.0 mm length were buried in 4 types of bone modeled. Vertical and oblique forces of lOON were applied on the center of the abutment, and the values of von Mises equivalent stress at the implant-bone interface were computed. The results showed that von Mises stresses at the marginal. bone were higher under oblique load than under vertical load, and the stresses were higher at the lingual marginal bone than at the buccal marginal bone under oblique load. Under vertical and oblique load, the stress in type I, II, III bone was found to be the highest at the marginal bone and the lowest at the bone around apical portions of implant. Higher stresses occurred at the top of the crestal region and lower stresses occurred near the tip of the implant with greater thickness of the cortical shell while high stresses surrounded the fixture apex for type N. The stresses in the crestal region were higher in Model 2 than in Model 1, the stresses near the tip of the implant were higher in Model 1 than Model 2, and Model 2 showed more effective stress distribution than Model.

• Korean Journal of Materials Research
• /
• v.30 no.11
• /
• pp.601-608
• /
• 2020

In this work, Ag₃PO₄/In₂S₃ nanocomposites with low loading of In₂S₃ (5-15 wt %) are fabricated by two step chemical precipitation approach. The microstructure, composition and improved photoelectrochemical properties of the as-prepared composites are studied by X-ray diffraction pattern (XRD), field emission scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), photocurrent density, EIS and amperometric i-t curve analysis. It is found that most of In₂S₃ nanoparticles are deposited on the surfaces of Ag₃PO₄. The as-prepared Ag₃PO₄/In₂S₃ composite (10 wt%) is selected and investigated by SEM and TEM, which exhibits special morphology consisting of lager size substrate (Ag₃PO₄), particles and some nanosheets (In₂S₃). The introduction of In₂S₃ is effective at improving the charge separation and transfer efficiency of Ag₃PO₄/In₂S₃, resulting in an enhancement of photoelectric behavior. The origin of the enhanced photoelectrochemical activity of the In₂S₃-modified Ag₃PO₄ may be due to the improved charge separation, photocurrent stability and oriented electrons transport pathways in environment and energy applications.

• Journal of Korean Home Economics Education Association
• /
• v.31 no.1
• /
• pp.39-58
• /
• 2019

The purpose of this study was to investigate the home economics pre-service teachers' verbal interactions during their teaching practicum. For this purpose, the class interactions of four pre-service teachers were recorded, and the data were analyzed using advanced Flanders' verbal interaction analysis. The major findings are as follows: First, the item with the highest proportion of occurrences consisted of the pre-service teachers' 'lectures', 'nonverbal conditions' and 'asks questions'. 'forms a positive learning atmosphere' and 'praises or encourages' exhibited fewer occurrences, and there was little 'giving direction', 'criticizing students or justifying authority'. Second, the instances of class interactions appeared in the form of 'asks questions-student talk response' or 'lecture-asks questions', and in the last class were 'ask questions-student talk initiation' and 'accepts or uses ideas of students'. Third, trends of verbal interactions tend to be generally indirect, and students' remarks have appeared acceptable and compassionate. Fourth, according to expert analysis, 'class management questions' and 'diffusion questions' have increased. Pre-service teachers can guide students through their learning activities, and students can expand their thinking through the teachers' questions. As these results demonstrate, self-study analyses of pre-service teachers and active support in field are needed.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.4
• /
• pp.359-365
• /
• 2015

Floor mortar experiences dry shrinkage by temperature and humidity difference of internal matrix with material type. Also, since floor mortar is influenced by environmental conditions during placing and curing period, cracks are likely to be occurred. In this study, it was evaluated the hardening and dry shrinkage properties of non-sintered binder based floor mortar utilizing alpha-hemihydrate gypsum which has expansibility in order to prevent crack of the floor mortar. It was applied to the construction site, and examined the effects of external environmental conditions on shrinkage deformation and cracking. Different types of slag accelerated initial and final setting in comparison with cement mortar and its compressive strength was satisfied standard compressive strength for floor mortar. Also shrinkage deformation behavior after the initial expansion exhibited a similar tendency with the cement mortar. From the field application result, no crack was found from slag mortar, and it is determined that the slag mortar has better dimensional stability than cement mortar caused by external environment conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.2
• /
• pp.665-674
• /
• 2011

This study examined how students' satisfaction with their major department influences their organizational commitment and intention to pursue a career in tourism-related fields among college students majoring in hospitality and tourism. The results indicated that their overall satisfaction with their department affected positively their organizational commitment but not the behavioral intention to pursue career in the tourism-related fields. Organizational commitment, on the other hands, exerted a positively significant influence behavioral intention to pursue tourism-related career. The results of this study underscored the needs for the educators to manage students' psychological attachment to the department they belong to and their major field of study. Continuous relationship-building efforts should be made for the students to pursue tourism-related career after graduation. Such efforts include efficient communication between faculty and students, extended supports from the school and alumni to the students, and last but not the least, sufficient supports from colleges.

• Journal of the Korean association of regional geographers
• /
• v.3 no.1
• /
• pp.13-34
• /
• 1997

The impact of a central place on daily living over wide outlying territory has been one of traditional subjects in the field of urban geography. The flow of rural population toward the central city of Chinju characterizes the population movement in Western Kyungnam, where the spillover of urban population into outlying areas, an especially prominent phenomenon in American society, does not occur. The central city of Chinju is supposed to be the most favored settlement area in Western Kyungnam. More than two thousands of teachers. who live in Chinju, cross the city boundary each morning to do their jobs in Western Kyungnam. But only ninety teachers living outside Chinju commute to the workplace in the city. The teachers willingly spend hours commuting each day to enjoy better quality of life in the central city. In fact, the central city of Chinju functions as bedroom communities for many middle-class workers in Western Kyungnam. On the basis of teachers' commuting behavior, four levels of Chinju's urban spheres are identified in Western Kyungnam. As Table-6 and Figure-2 show, the first-order level of Chinju's sphere includes most Myuns of Sanchung/Hadong Guns and some Myuns of Sachun/Gosung Guns. The second-order level comprises Sanchung/Sachun Eubs and many Myuns of Sachun /Gosung Guns. The third-order level is made up of Samchunpo, Hadong/Gosung/Eryung/Namhae/Habchun/Hamyang Eups, and many Myuns of Eryung/Namhae/Habchun Guns. And all of Guchang Gun and most Myuns of Hamyang Gun belong to the fourth-order level of Chinju's sphere. The influence sphere of Metropolitan Chinju is extended farther in the direction of less competition with other metropolises. Such a situation occurs to the west and south of Chinju. Daily commuting, defined as the journeys to and from work, is an excellent indicator for delimiting urban spheres of influence.