• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권9호
• /
• pp.576-583
• /
• 2004

This paper presents a buck circuit topology of high-frequency with a single switching device. It solved the problem which arised from hard-switching in high-frequency using a resonant snubber and operating under the principle of ZCS turn-on and ZVS turn-off commutation schemes. In the existing circuit, it has the voltage stress that is almost twice of input voltage in a free-wheeling diode. In the proposed circuit, it has the voltage stress that is lower than input voltage with modifing a location of free -wheeling diode. In this paper, it expained the circuit operation of each mode and analyzed feedback-loop stabilization. Also it confirmed the waveform of each mode with simulation result. The experiment result verified the simulation waveform and compared the voltage stress of a free -wheeling diode in the exsiting circuit with the voltage stress of that in the proposed circuit. Moreover, it compares and analyzes the proposed circuit's efficiency with the hard-switching circuit's efficiency according to the change of load current.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.669-679
• /
• 2003

Through AIS(Automatic Identification System), ITU-R suggested the navigational data communication between ships and between ships and shore stations for the better safety of navigation, and it requires two different the transmitting output power level depending on its operating mode. According to ITU's recommendation, these levels should reach within 20% of its final value in 1ms. In this paper, an adequate feedback control circuit for power amplifier module is designed and implemented.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.642-647
• /
• 1998

A new small-signal model for the controlled on-time boost power factor correction (PFC) circuit is presented. The proposed small-signal model is valid up to high frequencies over lKHz. The model can be used in designing the voltage feedback compensation of PFC circuits, the control bandwidth of which is maximized with auxiliary means of removing the low-frequency ripple from the output. The accuracy of the model is confirmed by a 200W experimental hardware

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.253-256
• /
• 2002

A programmable CMOS negative resistor has been designed and fabricated in a 0.5um double poly double metal technology. The proposed CMOS negative resistor consists of a positive feedback OTA and a bump circuit with Gaussian-like I-V curve. Measurements of the fabricated chip confirm that the proposed CMOS resistor shows various negative resistance according to control voltage.

• 소음진동
• /
• 제5권1호
• /
• pp.49-57
• /
• 1995

An electronic circuit device is developed such that the displacement between an electromagnet and a moving target can be estimated from the coil current measurement, and then applied to an active magnetic bearing system. In order to levitate the shaft without using displacement sensor the stable control gains are obtained from the linearized model which includes the gap estimation circuit. Experimental results show that the shaft, by the estimated gap feedback, can be levitated within $\pm$6 ${\mu}m$ positioning error.

• 전자공학회논문지B
• /
• 제30B권11호
• /
• pp.66-73
• /
• 1993

This paper presents an analog circuit implementation and experimental resuls of the Hopfield type neural network. The proposed architecture enables the reconfiguration betwewn feedback and feedforward networks and employs new circuit designs for the weight supply and storage, analog multilier, nd current-voltage converter, in order to achieve area efficiency as well as function al versatility. The layout design of the eight-neuron neural network is tested as an associative memory to verify its applicability to real world.

• 전기전자학회논문지
• /
• 제18권2호
• /
• pp.220-227
• /
• 2014

이 논문은 Dead-time을 갖는 톱니파 발생기를 이용하여 공통모드와 차동모드 피드백 루프를 구현한 Single-Inductor Dual-Output DC-DC Converter 설계에 관한 내용을 제시하고 있다. 제어회로에는 공통모드와 차동모드 피드백 루프를 Dead-time을 갖는 톱니파 발생기를 이용하여 동시에 사용하였다. 차동모드 피드백 루프에서 duty를 생성하기 위해서 전류 분배기 회로를 사용하여 공통모드 피드백에 의한 duty에 따라 dead-time이 유동적으로 변하는 톱니파형을 만드는 회로인 Dead-time을 갖는 톱니파 발생기를 추가하여 차동모드 피드백 회로를 구성하였다. 0.35um 공정을 사용하여 설계한 SIDO DC-DC Converter는 2.5V 입력으로부터 2.8V와 4.2V의 전압을 출력하며 최대 전력변환 효율은 95%이다. 출력간의 Cross regulation은 출력전류가 2배씩 증가할 경우 Boost1과 Boost2의 출력전압은 각각 3.57%, 4% 수준을 보이고 있다.

• 한국정보처리학회논문지
• /
• 제1권2호
• /
• pp.272-278
• /
• 1994

본 논문에서는 BIST(Built-In Self Test)시 순서회로내의 조합회로를 pseudoexhaustive 시험하는데 필요한 테스트 패턴 생성기와 응답 분석기를 제안한다. 제안하는 테스트 패턴 생성기는 테스트 패턴의 초기값을 스캔 인 할 수 있고, exhaustive test pattern 을 생성할 수 있다. 또한, 응답 분석기는 회로의 응답을 분 석할 수 있을 뿐만 아니라 응답 결과를 스캔 아웃할 수 있다. 이러한 테스트 패턴 생 성기와 응답분석기는 SRL과 LFSR을 결합하여 설계하였다.

• Journal of information and communication convergence engineering
• /
• 제18권3호
• /
• pp.201-206
• /
• 2020

This paper presents a new method for controlling the current of lighting LEDs without current sensors. This method can be used as backup against LED current sensor faults. LED lighting requires a circuit with a constant current in order to maintain the same brightness when the ambient temperature changes. Therefore, we propose a new current estimation method to provide backup in case of current sensor faults based on the calculation of the inductor current. In the fabricated circuit, the average current changes from 144.03 mA to 155.97 mA when the ambient temperature changes from 0℃ to 60℃. The application of this study can enable the fabrication of a driving IC for LEDs in the form of a single chip without sensing resistors. This is expected to reduce the complexity of the peripheral circuit and enable precise feedback control.

• 한국소음진동공학회논문집
• /
• 제14권6호
• /
• pp.455-462
• /
• 2004

This paper is concerned with the implementation of the active vibration suppression controller using analog circuit and microprocessor. The target active vibration controller is the positive position feedback(PPF) controller since it provides a simple algorithm suitable for both analog circuit and digital controllers. In this study, the analog PPF controller is realized using an operational amplifier and the digital PPF controller is realized using a low-cost micro-controller. The circuit diagrams are explained in detail. We then discuss the advantages and disadvantages of both methods from the view of practical implementation. Experimental results show that both implementation methods can be effectively used for the active vibration control but need to be chosen based on the mission objective.