• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.805-808
• /
• 1999

According to the results of this research, Production of Fold Concret Permanent-Form, was found to be possible by Concrete. The FCP-Form (Fold Concret Permanent-Form) Concrete had Compress strength 300kg/$\textrm{cm}^2$ and banding strength 120kg/$\textrm{cm}^2$. FCP-Form Model was made by the result of the first research. There was no mimute-crack on beam form and The outer surface of form was very smooth, and Those qualities it were made possible hand-made by experiment. With these results, The Production of FCP-Form seemed possible. In the banding load test, P-S showed increase of maxim load 12% than P-R. At the first stage of minute crack, under continuing loading size of crack increased. These phenomena seemed to be based on contribution of stress of inner bars in FCP-Form. In the test of defection. P-S shower about 10% banding load increase than P-R. FCP-Form Concrete was found to be efficient in compressibleness, defection, safety and use of material.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.31-32
• /
• 2023

Recently, with the digitalization of the construction industry, free-form building construction technology is developing. However, the technology for manufacturing free-form concrete panels is still insufficient. In this study, the surface error of the FCP according to the thickness of the lower silicon plate, which is a component of the existing lower multi-point press, was analyzed in order to manufacture a precise FCP. As a result of the analysis, it was found that the thinner the thickness, the larger the error value. These results can be used as a basis for existing research and are expected to be used for research on high-quality FCP manufacturing technology.

• Journal of Power System Engineering
• /
• v.15 no.1
• /
• pp.39-44
• /
• 2011

This study was to investigate the effects of stress ratio and anisotropy on Fatigue Crack Propagation(FCP) behavior of rolled magnesium alloy AZ31B. The experimental materials were a Mg-Al-Zn magnesium alloy. The FCP test was conducted on compact tension specimen by a servo-hydraulic fatigue testing machine in air at room temperature. Compact tension specimens were prepared from the extruded parallel and vertical rolling direction. The test condition was frequency of 10Hz and sinusoidal load stress ratios are 0.1 and 0.7. The FCP rates was automatically measured by a compliance method. In the case of the FCP of AZ31B, the FCP of both direction of LT and TL by anisotropy of specimens are almost same value. In lower stress ratio, the FCP of the LT, TL specimens are increased in lower ${\Delta}K$ region but higher ${\Delta}K$ regions are almost same value. Finally, the result of observed the surface crack, it expressed the quasi-cleavage fracture in lower ${\Delta}K$ region and straight mark on the aspect of the facet in high ${\Delta}K$ region.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.121-122
• /
• 2015

The demand on free-form buildings is gradually increasing, but there are several problems such as increased cost and construction duration, and decreased constructability at the construction phase upon construction of a building owing to the difficulty of member production-installation. To solve these problems, a technology to produce FCP using a CNC machine was developed. Basically, it delivers the information on a free-form building designed to the CNC machine, the shapes of RTM and PCM are created using the information delivered and FCP are produced with the RTM and PCM which act as forms. Since the construction duration and project cost are limited on site, the efficiency of FCP production-installation is significant for application of the technology. For it is almost impossible to change the production-installation layout and process once they are set in the construction phase, they should be carefully determined. Before the production-installation layout are established, it is necessary to analyze the factors that influence the duration. Thus, the study intends to analyze influence factors in PCM mold on estimation of the production-installation duration for FCP. According to the analysis of influence factors, a simulation model for estimation of the duration that changes depending on the constraint conditions can be built.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.11a
• /
• pp.21-22
• /
• 2023

In order to manufacture high-quality free-form concrete panel (FCP), it is necessary to analyze the limitations of free-form silicone mold (FSM) and conduct technology development research. Currently, the FSM used in FCP manufacture is classified into a side silicon mold(SSM) and a lower silicon mold(LSM). In this study, the limitations of each silicon mold were analyzed and solutions were proposed. In the case of side silicon mold, there is a limit to cannot supporting the side pressure of concrete. Therefore, a mold stacking method was proposed, and at the same time, a process of correcting the movement value of the rod was proposed. In the case of the lower silicon mold, there is a limit to completely implementing the design shape. Therefore, a real-time scanning method and a process of displaying FCP shape coordinates were proposed. The results of this study are expected to be used as basic data for manufacturing high-quality FCP.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.25 no.1
• /
• pp.52-60
• /
• 2022

Purpose: Colonoscopy is considered the most reliable method for the diagnosis of juvenile polyps. However, colonoscopic screening is an invasive and expensive procedure. Fecal calprotectin (FCP), a marker of intestinal inflammation, has been shown to be elevated in patients with polyps. Therefore, this study aimed to evaluate FCP as a screening biomarker for the diagnosis of juvenile polyps. Methods: This cross-sectional, observational study was conducted at the Pediatric Gastroenterology and Nutrition Department, Bangabandhu Sheikh Mujib Medical University, Dhaka, Bangladesh. For children with polyps, colonoscopic polypectomy and histopathology were performed. FCP levels were analyzed before and 4 weeks after polypectomy in all patients. Information was recorded in a datasheet and analyzed using the computer-based program SPSS. Results: The age of the children was between 2.5 and 12 years. Approximately 93% of the polyps were found in the rectosigmoid region. Children with juvenile polyps had elevated levels of FCP before polypectomy that subsequently normalized after polypectomy. The mean FCP levels before and after polypectomy were 277±247 ㎍/g (range, 80-1,000 ㎍/g) and 48.57±38.23 ㎍/g (range, 29-140 ㎍/g) (p<0.001), respectively. The FCP levels were significantly higher in patients with multiple polyps than in those with single polyps. Moreover, mean FCP levels in patients with single and multiple polyps were 207.6±172.4 ㎍/g and 515.4±320.5 ㎍/g (p<0.001), respectively. Conclusion: Colonic juvenile polyps were found to be associated with elevated levels of FCP that normalized after polypectomy. Therefore, FCP may be recommended as a noninvasive screening biomarker for diagnosis of colonic juvenile polyps.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.11a
• /
• pp.204-205
• /
• 2015

Demands for free-form buildings are on the rise, but such building designs require most cost and longer construction schedule, with less constructability due to challenges in construction member production and installation. FCP production technology has been developed using CNC machine in a bid to resolve the difficulties of member production. Exterior finishing panels of free-form building design must be divided in size and shape that can be produced by CNC machine. To solve this problem, constraints of CNC machine and correlations between CNC machine and panel need to be reviewed. Thus, the purpose of this study is to analyze decision factors on free-form concrete panel sizes produced by CNC machines. Through this study, FCP size can be optimized, which in turn can lead to improved FCP productivity and aesthetical quality of free-form building designs determined by the pattern of exterior finishing panels. CNC machine-enabled free-form concrete panel production technology will apply on site in the future, which will not only maximize the economic benefits of the technology but also support shorter construction schedule and better constructability.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.1
• /
• pp.117-122
• /
• 2005

This paper proposes an algorithm for Facial Characteristic Point(FCP) extraction. The FCP plays an important role in expression representation for face animation, avatar mimic or facial expression recognition. Conventional algorithms extract the FCP with an expensive motion capture device or by using markers, which give an inconvenience or a psychological load to experimental person. However, the proposed algorithm solves the problems by using only image processing. For the efficient FCP extraction, we analyze and improve the conventional algorithms detecting facial components, which are basis of the FCP extraction.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.65-66
• /
• 2022

In the construction industry, interest in technologies such as 3D Construction Printing (3DCP) is increasing, and research is being conducted continuously. In the case of atypical architecture, different shapes must be implemented, and the introduction of 3D printing technology is intended to solve it. Our researchers are conducting research to produce Free-form Concrete Panel (FCP). It automatically manufactures the FCP's formwork without any error with the design shape. At this time, the concrete nozzle based on the 3D printing technology is developed and the concrete is precisely extruded into the manufactured form to prevent the deformation of the formwork that can occur due to the concrete load. Therefore, in this study, the requirements for the development of 3D printing concrete nozzles for FCP manufacturing are analyzed. Based on the analyzed requirements, the first nozzle was developed. Such equipment is easy to shorten construction period and cost reduction in the atypical construction field, and is expected to be utilized as basic 3D printing equipment.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.33-34
• /
• 2018

Currently, free-form building has been increased worldwide. However, as a finishing material of free-form building, the production of free-form concrete panels(FCPs) spends lots of cost and efforts since it is difficult to reuse the FCP formwork and lots of workers are needed to make free-form curve. In addition, the technology to produce the FCP economically and easily is insufficient. Therefore, the objective of this study is a basic study regarding production management for developing free-form concrete panels. To achieve the objective, the property of FCP and condition for effective production management and production process are analyzed. The results of this study can utilize to develop the algorithm for FCP production management.