• Wind and Structures
• /
• v.13 no.3
• /
• pp.257-273
• /
• 2010

The aerodynamic and aero-elastic model tests of the China''s highest cooling tower has been carried out in the TJ-3 Boundary Layer Wind Tunnel of Tongji University. By adopting a scanivalve system, the external wind pressure is firstly measured on $12{\times}36$ taps for a single tower, two and four grouped towers under the condition of both smooth flow and the boundary layer due to surrounding geographic and building topography. The measurements of internal wind pressure distribution of $6{\times}36$ taps are taken for a single tower under the various ventilation ratios ranging from 0% to 100% of stuffing layers located at the bottom of the tower. In the last stage, the wind tunnel tests with an aero-elastic model are carefully conducted to determine wind-induced displacements at six levels (each with eight points) with laser displacement sensors. According to the measurement results of wind pressure or vibration response, the extreme aerodynamic loading values of the single or grouped towers are accordingly analyzed based on probability correlation technique.

• Journal of Korean Association for Spatial Structures
• /
• v.11 no.2
• /
• pp.63-70
• /
• 2011

Livestock buildings are rural facilities as vulnerable to natural disasters as vinyl houses. Many of livestock buildings have a roof but without side walls. The roof of such structures is easily blown away by a typhoon and this results in a heavy loss. Therefore, farmers install winch curtains on the sides to prevent damages caused by typhoons. This study purposed to examine the distribution of wind pressure coefficient among different positions of livestock shed roof according to the opening of side walls. It was found that according to the distribution of peak external pressure coefficient on the roof surface of livestock shed, the wind blowing at wind angle $0^{\circ}$ was disadvantageous to roof surface regardless of the presence of side walls. However, it was confirmed that the peak external pressure coefficient was affected by wind angle and the length of eave depending on the presence of side walls.

• Journal of Haehwa Medicine
• /
• v.8 no.2
• /
• pp.171-189
• /
• 2000

By Literatural studying on migraine, The results were obtained as fallow : 1. A different name on migraine were called hemicrania(頭偏痛, 邊頭痛, 偏頭風). 2. In the cause of a disease in migraine, the cases were clasified into the fallowing kind : internal cause were a decline in energy and blood(氣血具虛), external cause were outside evil(外邪) in wind cold heat wetness(風寒暑濕), non internal, external cause were exhaustion. The right side migraine were concerned phlegm heat, the right side migraine were concerned wind decline in blood. 3. Migraine is appeared on the side, For the reason, liver function in excess of normal limits(肝陽上亢), a sudden of liver fire(肝火) is becomeed of invasion upon soyangkuong(少陽經) in internal external cause 4. Usage method of medicines is appeared that order underclothes theraphy(內服法), to pump out in nose theraphy, to join head theraphy(頭點法), heating smoke theraphy(熏煙法) 5. CNIDII RHIZOMA(川芎) is in mostly general use for migraine, in that order LEDEBOURIELLAE RADIX(防風) ANGELICAE DAHURICAE RADIX(白芷) ASARI HERBA CUM RADICE(細辛) NOTOPTERYGII RHIZOMA(羌活) GLYCYRRHIZAE RADIX(甘草) CHRYSANTHEMI FLOS(菊花) BUPLEURI RADIX(柴胡) SCUTELLARIAE RADIX(黃芩) ANGELICAE GIGANTIS RADIX(當歸) GYPSUM FIBROSUM(石膏) MENTHAE HERBA(薄荷) GLYCYRRHIZAE RADIX(炙甘草) VITICIS FRUCTUS(蔓荊子), nature is in mostly general hot warm(辛溫), bitter cold(苦寒), guikuong(歸經) is in mostly general liver gall kuong(肝膽經), efficacy is in mostly general to remove wind pain (祛風止痛) and to down fire(瀉火).

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.11
• /
• pp.9-16
• /
• 2021

As the climate changes rapidly due to warming, it is becoming very important to ensure the stability of environmental structures. It is necessary to choose a material that withstands repeated external forces (wind loads) and satisfies members and joints that have energy absorbing power. Even if the strength of the traffic light attachment is sufficient, if the rigidity is insufficient, there is a limit to the displacement during strong winds. Excessive deformation may cause damage and fall, resulting in a safety accident. The author intends to study mechanical properties and resistance to external environment as a structural material capable of withstanding wind load (50m/sec) by fabricating a C/GFRP composite traffic light attachment using the pultrusion method (Pultrusion).

• International Journal of Aeronautical and Space Sciences
• /
• v.11 no.4
• /
• pp.345-350
• /
• 2010

The repetitive vibrating action of an aerodynamic load causes an external fuel tank's horizontal fin to experience a shorter life cycle than its originally predicted one. Store separation analysis is needed to redesign the fin of an external fuel tank. In this research, free-drop tests were conducted using 15% scaled models in a subsonic wind tunnel in order to analyze the store separation characteristics of an external fuel tank. The store separation trajectory based on grid tests was also obtained to verify the results of the free-drop tests. The results acquired from the free-drop tests correlated well with the grid tests in regards to the trajectories and behavior of the stores separated from the aircraft. This agreement was especially noted in the early stages of the store separation.

• Journal of the Korean Solar Energy Society
• /
• v.24 no.4
• /
• pp.27-33
• /
• 2004

Mechanical load measurements on blade and tower of Vestas 100 kW wind turbine has been reformed in Wollyong test site, Jeju island. The experimental procedure for the measurement of wind turbine loads, such as edgewise(lead-lag) bending moment, flapwise bending moment, and tower base bending moment, has been established. The test facilities consisting of strain-gauges, telemetry and T-Mon system are installed in the wind turbine. Strain gauges are on-site calibrated against load cell prior to monitoring the wind turbine loads. Using the test setup, the loads on the components are being measured and analysed for various external conditions of the wind turbine. A set of results for near rated wind speed has been presented in this paper.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2009.01a
• /
• pp.596-600
• /
• 2009

We are developing a simple low-cost wind velocity sensor based on small microphones. The sensor system consists of 4 microphones covered with specially shaped wind screens, 4 pre-amplifiers that respond to low frequency, and a commercial sound interface with multi channel inputs. In this paper, we first present the principle of the sensor, i.e., technique to successfully suppress the influence of external noise existing in the environment in order to determine the wind velocity and the wind direction from the output from a microphone. Then, we present an application for generating realistic motions of a virtual tree swaying in real wind. Although the current sensor outputs significant leaps in a measured sequence of directions, the interactive animations demonstrate that it is usable for such applications, if we could reduce the leaps to some degree.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.439-442
• /
• 2009

As a result of increasing environmental concern, the penetration of renewable power on power systems is now increasing. Wind energy can be considered as the most economical energy sources to generate electricity without depletion of fossil fuel. The penetration of wind energy from wind farm is getting larger and larger, so we need adequate control strategies for wind farm. To devise adequate control strategies for wind farm, time domain simulation analysis needs to be performed. This presents a Simultaneous Implicit-based time domain simulation algorithm for wind farm with DFAG (Doubly Fed Asynchronous generator) connected to the external power systems. This paper shows an illustrative example with a 5-bus test system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.1
• /
• pp.41-51
• /
• 2018

Downwash from helicopter rotor blades and external winds from various maneuvering make an unguided rocket change its trajectory and range. For the prediction of the trajectory and range, it is essential to consider the downwash effect. In this study, an algorithm was developed to calculate 6-Degree-Of-Freedom(6 DOF) forces and moments exerting on the rocket, and total flight trajectory of a 2.75-inch unguided rocket in a helicopter downwash flow field. Using Actuator Disk Model(ADM) analysis result, the algorithm could analyze the entire trajectory in various initial launch condition such as launch angle, launch velocity, and external wind. The algorithm that considered the interference between a fuselage and external winds could predict the trajectory change more precisely than inflow model analysis. Using the developed algorithm, the attitude and trajectory change mechanism by the downwash effect were investigated analyzing the effective angle of attack change and characteristics of pitching stability of the unguided rocket. Also, the trajectory and range changes were analyzed by considering the downwash effect with external winds. As a result, it was concluded that the key factors of the rocket range change were downwash area and magnitude which effect on the rocket, and the secondary factors were the dynamic pressure of the rocket and the interference between a fuselage and external winds. In tailwind case which was much influential on the range characteristics than other wind cases, the range of the rocket rose as increasing the tailwind velocity. However, there was a limit that the range of the rocket did not increase more than the specific tailwind velocity.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.370-373
• /
• 2007

For the development of wind turbine, generally simulator is used. Simulator include wind turbine components. e.g blades, pitch and pitching method, rotor, yaw system, tower, drive train and so on. Few the more, it include a external circumstance. e.g wind speed, wind direction, air density. these basic parameters be used for the control of wind turbine by wind turbine controller in wind turbine simulator. The wind turbine controller can be designed in the wind turbine simulator. But a developer must make the real control system that will be made using PLC or PC or other processor. The developer must verify the function of control system. that is control algorithm , I/O function, communication, sequence and so on. This verification is possible if we substitute the real wind turbine control system for wind turbine controller in the simulator.