• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.687-694
• /
• 2008

This paper is focused on the improvement of MOS device reliability related to deuterium process. The injection of deuterium into the gate oxide film was achieved through two kind of method, high-pressure annealing and low-energy implantation at the back-end of line, for the purpose of the passivation of dangling bonds at $SiO_2/Si$ interface. Experimental results are presented for the degradation of 3-nm-thick gate oxide ($SiO_2$) under both negative-bias temperature instability (NBTI) and hot-carrier injection (HCI) stresses using P and NMOSFETs. Annealing process was rather difficult to control the concentration of deuterium. Because when the concentration of deuterium is redundant in gate oxide excess traps are generated and degrades the performance, we found annealing process did not show the improved characteristics in device reliability, compared to conventional process. However, deuterium ion implantation at the back-end process was effective method for the fabrication of the deuterated gate oxide. Device parameter variations under the electrical stresses depend on the deuterium concentration and are improved by low-energy deuterium implantation, compared to conventional process. Our result suggests the novel method to incorporate deuterium in the MOS structure for the reliability.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.5
• /
• pp.383-389
• /
• 2004

In this paper. we propose the bias compensation methods and the eigenvoice method using the mean of dimensional eigenvoice to improve the performance of rapid speaker adaptation based on eigenvoice under mismatch between training and test environment. Experimental results for vocabulary-independent word recognition task (using PBW 452 DB) show that the proposed methods yield improvements for small adaptation data. We obtained about 22∼30% relative improvement by the bias compensation methods as amount of adaptation data varied from 1 to 50, and obtained 41% relative improvement in error rate by the eigenvoice method using the mean of dimensional eigenvoice with only single adaptation word.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.2
• /
• pp.29-34
• /
• 2004

The linear type flux pump aims to compensate a little bit decremental persistent current of the HTS magnet in NMR and MRI spectrometers. The flux pump mainly consists of DC bias coil, 3-phase AC coil and Nb foil. The persistent current in closed superconductive circuit can be easily adjusted by the 3-phase AC current, its frequency and the DC bias current. In the experiment, it has been investigated that the flux pump can effectively charge the current in the load coil of 543 mH for various frequencies in 18 minutes under the DC bias of 10 A and the AC of 5 $A_{rms}$. The maximum magnitudes of pumping current and load magnet voltage are 0.72 A/min and 20 ㎷, respectively. Based on simulation results by the FEM are proved to nearly agree with experimental ones.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.3
• /
• pp.44-53
• /
• 2003

Cu/C films were prepared at room temperature under $Cu(hfac)_2-Ar-H_2$ atmosphere in order to obtain metallized polymer by using ECR-MOCVD(Electron Cyclotron Resonance Metal Organic Chemical Vapor Deposition) coupled with a DC bias system. The room temperature MOCVD on polymer substrate could be possible by collaboration of ECR and a DC bias. Structural analysis of the films by ECR was found that fine copper grains embedded in an amorphous polymer matrix with indistinctive interfacial layer. The increase in $H_2$ contents brought on copper-rich film formation with low electric resistance. On the other hand carbon-rich films with low sheet electric resistance were prepared in argon atmosphere. The electric sheet resistance of Cu/C films with good interfacial property were controlled at $10^8$~$10^0$ Ohm/sq. ranges by the $H_2$/Ar mole ratio and the shielding effectiveness of the film showed maximum up to 45dB in the our experimental range.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.164-169
• /
• 2001

The active magnetic bearing has many advantages - an active positioning, no contact and lubrication free motion - and is widely used in high precision motion stages. But, the conventional magnetic bearings composed of electromagnets only are power consuming due to their bias current and have the excessive heat generation, which can make the repeatability of the positioning system worse. To overcome this drawback, we developed a novel permanent magnet (PM) biased linear magnetic bearing for a high precision magnetically levitated stage. The permanent magnets provide a bias flux and generate a bias force, and the electromagnet increases or reduces a flux of the permanent magnets and gives a levitation force. This paper presents a theoretical magnetic circuit analysis, FEM analysis and experimental data from the 1-DOF tests, and compares the theoretical power consumption of the electromagnetic bearings and the PM biased linear magnetic bearings. The PM biased linear magnetic bearing presented in this paper gives better load capacity but lower power consumption than a conventional electromagnetic bearing and will be adopted in our 6-DOF high precision linear positioning maglev stage.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.598-601
• /
• 2006

The radio signal in GNSS was intentionally designed with two frequencies in order to combat the dispersion error caused by trans-ionospheric propagation. By measuring the path delay independently at the two, widely spaced GPS frequencies, L1 & L2, the TEC along the path from satellite to receiver can be measured directly. The issue with dual frequency measurement of the ionosphere is the calibration of L1/L2 interfrequency biases. L1/L2 interfrequency biases are generated because physical electric signal paths of L1 and L2 circuits are different from each other for both satellites and receiver. Conventionally L1/L2 interfrequency bias is estimated and broadcasted by 2D ionospheric model. In this paper, we estimated IFB (interfrequency bias) by 2D & 3D ionospheric models including real time filter methods and compared the result of those and concluded the merit of 3D tomography model to recover the problem of 2D thin shell model. We confirmed our conclusion by experimental data.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.188-189
• /
• 2007

The etching characteristics of $Al_2O_3$ films using the inductively coupled plasma (ICP) was investigated. The etch gas was the mixture of $BCl_3$ and He. The effect of ICP source and bias powers on etch rate and etch selectivity to polycrystalline Si was investigated in the etch process of $Al_2O_3$. The etch rate of $Al_2O_3$ film was 23nm/min when the source power and bias power were 600W and 60W, respectively. The results also indicated that the etch selectivity to polycrystalline Si could not be enhanced to be higher than 1.0 by changing the ICP source power and bias power, under the experimental conditions used in the present work. Based on plasma parameters extracted from Langmuir probe data, the etching mechanism of $Al_2O_3$ film was discussed in detail.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.2
• /
• pp.67-70
• /
• 2013

In this study, we changed the input parameters (gas mixing ratio, RF power, DC bias voltage, and process pressure), and then monitored the effect on TiN etch rate and selectivity with $SiO_2$. When the RF power, DC-bias voltage, and process pressure were fixed at 700 W, - 150 V, and 15 mTorr, the etch rate of TiN increased with increasing $CF_4$ content from 0 to 20 % in $CF_4$/Ar plasma. The TiN etch rate reached maximum at 20% $CF_4$ addition. As RF power, DC bias voltage, and process pressure increased, all ranges of etch rates for TiN thin films showed increasing trends. The analysis of x-ray photoelectron spectroscopy (XPS) was carried out to investigate the chemical reactions between the surfaces of TiN and etch species. Based on experimental data, ion-assisted chemical etching was proposed as the main etch mechanism for TiN thin films in $CF_4$/Ar plasma.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.37 no.2
• /
• pp.55-62
• /
• 2019

The stereo geometry establishment based on the precise sensor modeling is prerequisite for accurate stereo data processing. Ground control points are generally required for the accurate sensor modeling though it is not possible over the area where the accessibility is limited or reference data is not available. For the areas, the relative orientation should be carried out to improve the geometric consistency between the stereo data though it does not improve the absolute positional accuracy. The relative orientation requires conjugate points that are well distributed over the entire image region. Therefore the automatic conjugate point extraction is required because the manual operation is labor-intensive. In this study, we applied the method consisting of the key point extraction, the search space minimization based on the epipolar line, and the rigorous outlier detection based on the RPCs (Rational Polynomial Coefficients) bias compensation modeling. We tested different parameters of window sizes for Kompsat-2 across track stereo data and analyzed the RPCs precision after the bias compensation for the cases whether the epipolar line information is used or not. The experimental results showed that matching outliers were inevitable for the different matching parameterization but they were successfully detected and removed with the rigorous method for sub-pixel level of stereo RPCs precision.

• Restorative Dentistry and Endodontics
• /
• v.46 no.3
• /
• pp.37.1-37.11
• /
• 2021

Objectives: This systematic review evaluated the efficacy of the supplementary use of the XP-endo Finisher on bacteria content reduction in the root canal system. Materials and Methods: In-vitro studies evaluating the use of the XP-endo Finisher on bacteria content were searched in four databases in July 2020. Two authors independently screened the studies for eligibility. Data were extracted, and risk of bias was assessed. Data were meta-analyzed by using random-effects model to compare the effect of the supplementary use (experimental) or not (control) of the XP-endo Finisher on bacteria counting reduction, and results from different endodontic protocols were combined. Four studies met the inclusion criteria while 1 study was excluded from the meta-analysis due to its high risk of bias and outlier data. The 3 studies that made it to the meta-analysis had an unclear risk of bias for at least one criterion. Results: No heterogeneity was observed among the results of the studies included in the meta-analysis. The study excluded from the meta-analysis assessing the bacteria counting deep in the dentin demonstrated further bacteria reduction upon the use of the XP-endo Finisher. Conclusions: This systematic review found no evidence supporting the supplementary use of the XP-endo Finisher on further bacteria counting the reduction in the root canal.