• 조명전기설비학회논문지
• /
• 제29권5호
• /
• pp.50-56
• /
• 2015

As rotor position is a reference of coordinate in vector control of PMSM, the information of exact rotor position is required. To measure the position of motors, hall-effect sensors, encoders, resolvers, etc. are used. Among these sensors, resolvers have good endurance in the variation of circumstance and can be used in a wide range of temperature, but resolvers are less exact than encoders. In addition, resolvers have a drawback that the output signal contains periodic error components. Thus, this paper proposes a compensation method for the unique position error in resolvers using Kalman filter to achieve high performance control of PMSM. The validity of the proposed scheme is demonstrated through simulation studies.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.64.5-64
• /
• 2001

It is a very important problem that we grasp the accurate position at car navigation system. The GPS has used for knowing position because of accumulating few errors, but it have errors that are Tropospheric error, ionospheric error and Multipath error and so on. In this paper, We estimate moving position of a vehicle by Kalman filter using initial value after deducing the line equation using initial value and target value of map data. Then, we compensate GPS errors compare estimated poing with GPS errors. The experimental results have shown that are compared position data during real travel with compensated position data which are got after applying the algorithm ...

• 전력전자학회논문지
• /
• 제27권6호
• /
• pp.481-488
• /
• 2022

This study proposes compensation methods for the initial position error and torque ripple in vector control of two-phase hybrid stepping motors. Stepping motors have an asymmetrical structure due to misalignment, such as the eccentricity generated by the manufacturing and assembly process. When vector control is applied using the position information measured by an incremental encoder attached to the rotor shaft of such stepping motors, the following problems occur. First, an initial position error occurs during the forced excitation process for the initial rotor position alignment. Second, torque ripple corresponding to the mechanical rotation frequency is generated. In this study, these non-ideal phenomena that occur in vector control of the stepping motor are analyzed, and compensation methods are proposed to eliminate them. The validity of the proposed initial position error and torque ripple compensation methods is verified through experiments on a two-phase hybrid stepping motor drive system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1325-1328
• /
• 2007

When we visualize the sound field radiated from a spherical sound source, spherical acoustic holography is proper among acoustic holography methods. However, there are measurement errors due to sensor position mismatch, sensor mismatch, directivity of sensor, and background noise. These errors are amplified if one predicts the pressures close to the sources: backward prediction. The goal of this paper is to quantitatively examine the effects of the error due to sensor position mismatch on acoustic pressure estimation. This paper deals with the cases of which the measurement deviations are distributed irregularly on the hologram plane. In such cases, one can assume that the measurement is a sample of many measurement events, and the cause of the measurement error is white noise on the hologram plane. Then the bias and random error are derived mathematically. In the results, it is found that the random error is important in the backward prediction. The relationship between the random error amplification ratio and the measurement parameters is derived quantitatively in terms of their energies.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2012년도 춘계학술대회
• /
• pp.160-161
• /
• 2012

This paper is to develop & analyze the position & direction error equations in the free-gyro positioning & directional system by using two free gyros and is to find out the amount of the errors. First, the position & direction error equations are introduced and developed, based on the position & direction equations. Second, the value of errors is discussed based on sensors errors.

• Journal of Magnetics
• /
• 제18권4호
• /
• pp.454-459
• /
• 2013

This paper deals with an optimal angle error reduction method of magnetic position sensor using hall effect elements. The angle detection simulation for the magnetic position sensor is performed by 3 dimensional finite element method and Taguchi method, one of the design of experiments. The magnetic position sensor is required to generate ideal sine and cosine waveforms from its hall effect elements according to rotation angle for precise angle information. However, the output signals are easy to include harmonics due to uneven magnetic field distribution from permanent magnet in the air-gap in the vicinity of hall effect elements. For the Taguchi method, three design parameters related to position of hall effect elements and shape of back yoke are selected. The characteristics of optimal magnetic position sensor are compared with those of original one in terms of simulation as well as experiment. Finally, the performances of the motor adopting original model and optimal model are represented for the purpose of verification of motor performance due to signals from magnetic position sensor.

• 한국생산제조학회지
• /
• 제4권3호
• /
• pp.39-47
• /
• 1995

This paper suggests generalize mathematica mode for the benefit of volumetric error analysis of a multi-axis machine tool machining a sculptured surfaces. The volumetric error, in this paper, is defined as a three dimensional error at the cutting point, which is caused by the geometric errors and the kinematic errors of each axis and alignment errors of the cutting tool. The actual cutting position is analyzed based on the form shaping model including a geometric error of the moving carriage, where a form shaping model is derived from the homogeneous transformation matrix. Then the volumetric error is obtained by calculating the position difference between the actual cutting position and the ideal one calculated from a Nonuniform Rational B-Spline named as NURES. The simulation study shows the effectiveness for predicting the behavior of machining error and for the method of error compensation.

• 한국기계가공학회지
• /
• 제15권4호
• /
• pp.67-72
• /
• 2016

Planetary gear sets are widely used in power transmission components, which have high efficiency and good durability. Their most important design parameter is the load-sharing characteristics among several planetary gears. In this study, the load sharing of planetary gears was analyzed according to the carrier pinhole position error of planetary gear sets. The loads acting on planetary gears varied with the pinhole position error of the carrier, and the load sharing of planetary gears improved as the input load increased. In addition, the load of the planetary gear with a carrier pinhole position error was relatively higher than that of other planetary gears without carrier pinhole position errors. This trend appeared more clearly in the non-floating-type carrier than the floating-type carrier.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집
• /
• pp.53-56
• /
• 2004

This paper describes the method of position error reduction in Linear Pulse Motor (LPM). Though the micro step exiting method is applied, the vibration and position error caused by trust distortion from mechanism still remains. This paper presents the method for reduction of position error on moving the mover at whole cycle, by compensating a scale factor through real-time control of the PWM pulse width corresponding to exiting current command and absolute position error from linear encoder.

• 한국해양공학회지
• /
• 제31권1호
• /
• pp.28-35
• /
• 2017

This paper introduces a GPS-aided dead reckoning algorithm that asymptotically estimates the heading bias error of a magnetic compass based on geodetic north, improves the position error accumulated by dead reckoning, and helps the estimated position of an AUV to represent a position in the NED coordinate system, by receiving GPS position information when surfaced. Based on the results of a simulation, the locational error was bounded with a modest distance, after estimating the AUV position and heading bias error of the magnetic compass when surfaced. In other words, it was verified that proposed algorithm improves the position error in the NED coordinate system.