• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.6
• /
• pp.446-457
• /
• 2020

Crescentic sand bar in the coastal zone of eastern Korea is a common morphological feature and the rhythmic patterns exist constantly except for high wave energy events. However, four consecutive typhoons that directly and indirectly affected the East Sea of Korea from September to October in 2019 impacted the formation of longshore uniform sand bar and overall shoreline retreats (approx. 2 m) although repetitive erosion and accretion patterns exist near the shoreline. Widely used XBeach to predict storm erosions in the beach is utilized to investigate the morphological response to a series of storms and each storm impact (NE-E wave incidence). Several calibration processes for improved XBeach modeling are conducted by recently reported calibration methods and the optimal calibration set obtained is applied to the numerical simulation. Using observed wave, tide, and pre & post-storm bathymetries data with optimal calibration set for XBeach input, XBeach successfully reproduces erosion and accretion patterns near MSL (BSS = 0.77 (Erosion profile), 0.87 (Accretion profile)) and observed the formation of the longshore uniform sandbar. As a result of analysis of simulated total sediment transport vectors and bed level changes at each storm peak Hs, the incident wave direction contributes considerable impact to the behavior of crescentic sandbar. Moreover, not only the wave height but also storm duration affects the magnitude of the sediment transport. However, model results suggest that additional calibration processes are needed to predict the exact crest position of bar and bed level changes across the inner surfzone.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.349-354
• /
• 2001

In this study, we investigated the effect of the impacting ang1e of particles, the scanning times and the stand-off distance on the surface roughness and the weight-loss rate of samples with no mask, and the wall profile and overetching of samples with different mask pattern in powder blasting of soda-lime glass. The varying parameters were the different impact angles between 50$^{\circ}$ and 90$^{\circ}$, scanning times of nozz1e up to 40 and the stand-off distances 70mm and 100mm. The widths of mask pattern were 0.2mm, 0.5mm and 1mm. The powder was alumina sharp particles, WA#600. The mass flow rate of powder during the erosion test was fixed constant at 175g/min and the blasting pressure of powder at 0.2MPa

• Journal of Ocean Engineering and Technology
• /
• v.32 no.2
• /
• pp.116-122
• /
• 2018

Dean's equilibrium beach profile formula was used to investigate the correlation between the static shoreline position and the incident wave energy. The effect of the longshore sediment transport was neglected, and the results showed the reasonable agreement compared with the field observations of Yates et al.(2009), which were conducted for almost 5 years on southern California beaches, USA. The shoreline response varies with the scale factor of Dean's equilibrium beach profile. This implies that the shoreline response could be simply estimated using the sampled grain size without laborious long-term field work. Therefore, the present study results are expected to be practically used for the layout design of submerged or exposed detached breakwaters although the further work is required for performance verification. In addition, after laborous mathematical reviews, the linear relation between incident energy and shoreline response, which was obtained from Yates's field study, yielded a clear mathematical equation showing how the beach slope is related to the grain size.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.6
• /
• pp.28-34
• /
• 2004

The old technique of sandblasting which has been used for decoration of glass surface has recently been developed into a powder blasting technique for brittle materials such as glass, silicon and ceramics, capable of producing micro structures larger than 100${\mu}{\textrm}{m}$. In this study, we introduced oblique powder blasting, and investigated the effect of the impacting angle of particles, the scanning times and the stand-off distance on the surface roughness and the weight-loss rate of samples with no mask, and the wall profile and overetching of samples with different mask pattern in powder blasting of soda-lime glass. The varying parameters were the different impact angles between 50$^{\circ}$ and 90$^{\circ}$, scanning times of nozzle up to 40 and the stand-off distances 70mm and 100mm. The widths of mask pattern were 0.2mm, 0.5mm and 1mm. The powder was alumina sharp particles, WA #600. The mass flow rate of powder during the erosion test was fixed constant at 175g/min and the blasting pressure of powder at 0.2Mpa.

• The Journal of Engineering Geology
• /
• v.10 no.2
• /
• pp.52-74
• /
• 2000

The basement rock of upper stream of Keum River Valley consists of Precambrian gneiss which is resistant to weathering. That of mid and lower stream valley, however, is mainly composed of Mesozoic granites which are vulnerable to weathering. The upstream part of Geum River Basin is typified by the deeply-incised and steep meandering streams, whereas mid and lower part is characterized by wide floodplain and gently dipping river bottom toward the Yellow Sea. In particular flooding deposits, in which are imprinted a number of repetitions of erosion and sedimentation during the Holocene, are widely distributed in the lower stream of Geum River Basin. For understanding of erosions in the mid and lower stream of Geum River Basin, the rate of erosion of each small basins were estimated by using the data of field survey, erosional experiments and GIS ananlysis. It was revealed that erosion rate appeared highest in granite areas, and overall areas, in this field survey were represented by relatively high erosion rates. By implemeatation of remote sensing and imagery data, the temporal changes of river bed sediments for about last 11 years were successfully monitored. Observed as an important phenomenon is that the river bed has been risen since 1994 when an embankment (Dyke) was constructed in the estuarine river mouth. From the results derived from the detailed river bed topographical map made in this investigation, the sedimentation of the lower river basin is considered to be deposited with about 5 cm/year for the last 11 years. Based on this river bed profile analysis by HEC-6 module, it is predicted that Geum River bed of Ganggyeong area is continuously rising up in general until 2004. Although extraction of a large amount of aggregates from Gongju to Ganggyung areas, the Ganggyung lower stream shows the distinct sedimentation. Therefore, it is interpreted that the active erosions of tributary basins Geum drainage basins can affect general river bed rising changes of Geum River.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.5 s.149
• /
• pp.578-585
• /
• 2006

Cavitation related erosion damages on semi-spade rudder generally occur at around leading edge of lower-face and behind gap of lower pintle. To get the idea of gap entrance profile for the latter case, a series of tests with large models has been carried out at MOERI. In the tests, the flow pattern around lower pintle have been investigated and visualized by high speed camera. Additionally, cavitation inception tests and pressure measurements have also been conducted for better comparison. As a result a new model (F rudder) has been developed. The new model turned out to have stable pressure distribution along the surface and so the cavitation inception speeds within ${\pm}5^{\circ}$ of rudder angle were delayed approx. 4 knots in average.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.3
• /
• pp.203-207
• /
• 2008

Chemical mechanical polishing (CMP) allows the planarization of wafers with two or more materials. There are many elements such as slurry, polishing pad, process parameters and conditioning in CMP process. Especially, polishing pad is considered as one of the most important consumables because this affects its performances such as WIWNU(within wafer non-uniformity) and MRR(material removal rate). In polishing pad, grooves and pores on its surface affect distribution of slurry, flow and profile of MRR on wafer. A subject of this investigation is to apply CMP for planarization of shallow trench isolation structure using microstructure(MS) pad. MS pad is designed to have uniform structure on its surface and manufactured by micro-molding technology. And then STI CMP performances such as pattern selectivity, erosion and comer rounding are evaluated.

• Journal of Korean Port Research
• /
• v.14 no.4
• /
• pp.451-461
• /
• 2000

The design and maintenance of navigation channel and water facilities of an harbor which is located at the mouth of river or at the estuary area are difficult due to the complexity of estuarial water and sediment circulation. Effects of deepening navigable waterways, of changing coastline configurations, or of discharging dredged material to the open sea are necessary to be investigated and predicted in terms of water quality and possible physical changes to the coastal environment. A borad analysis of the transport mechanism in the estuary area was made in terms of sediment property, falling velocity, concentration and flow characteristics. In order to simulate the transport processes, a two-dimensional finite element model is developed, which includes erosion, transport and deposition mechanism of suspended sediments. Galerkin’s weighted residual method is used to solve the transient convection-diffusion equation. The fluid domain is subdivided into a series of triangular elements in which a quadratic approximation is made for suspended sediment concentration. Model could deal with a continuous aggregation by stipulating the settling velocity of the flocs in each element. The model provides suspended sediment concentration, bed shear stress, erosion versus deposition rate and bed profile at the given time step.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.6
• /
• pp.569-577
• /
• 2009

As the scale factor of model propellers utilized in cavitation test is about 40, it is difficult to find out practical countermeasures against the small area erosions on the blade tip region throughout model erosion tests. In this study, a partial propeller blade model was used for the observation of cavitation pattern for the eroded propeller. A partial propeller blade model was manufactured from 0.7R to tip with expanded profile and with adjustable device of angle of attack. Reynold's number of a partial propeller blade model is 7 times larger than that of a model propeller. Also, anti-singing edge and application of countermeasures to partial propeller blade model which produced in large scale can be more practical than a model propeller. For the observation of cavitation at high Reynold's number, high speed cavitation tunnel was used. To find out the most severe erosive blade position during a revolution, cavitation observation tests were carried out at 5 blade angle positions.

• Journal of the Korean earth science society
• /
• v.25 no.8
• /
• pp.764-773
• /
• 2004

The soil in wildfire area Sacheon-myeon, Gangneung, Gangweon Province, Korea, were investigated to clarify pattern of the soils. The soils were classified into 5 types on the basis of vegetation, types of organic matter. thickness of soil horizons, and completeness of soil profile. Each type showed different erosion pattern and Landsat ETM image. Coverage of plant leaves, litter, root, ash and other organic matter was an important component that affected soil color and reflectance of Landsat image (digital number). Although the NDVI (Normalized Distribution Vegetation Index) method in the wildfire area did not show much difference in soil types, the applied supervised classification method showed characteristic pattern of Landsat ETM image of soil types. This study showed that the applied supervised Landsat TM image classification in wildfire area is an effective way to estimate the distribution of erosion pattern of soil in wildfire area.