• 한국전자파학회논문지
• /
• 제23권4호
• /
• pp.507-514
• /
• 2012

본 논문에서는 함체 내부의 PCB에 있는 트레이스 파원에 의한 함체의 공진 특성 해석법을 제안하고 있다. 함체 내부의 전자계를 계산하기 위해 PCB 트레이스에 형성되는 전류 분포 및 PCB 유전체의 경계면에서 만족하는 경계면 전계 분포에 관한 연립 적분방정식을 유도하였으며, 연립 적분방정식의 해는 Galerkin의 모멘트 법으로 구하고 있다. 그 결과, 함체의 공진 특성은 실험 결과 및 HFSS 툴에 의한 시뮬레이션 결과와도 잘 일치하고 있으며, 함체의 공진 주파수는 PCB 트레이스의 위치에 의해 달라진다는 것을 확인하고 있다. 이론 해석의 타당성을 검증하기 위해 반사 계수의 이론치를 측정치와도 비교하고 있다.

• 에너지공학
• /
• 제23권4호
• /
• pp.183-188
• /
• 2014

Solenoid operated electromagnetic control valve (ECV) using in an external variable displacement swash plate type compressor is widely used for air conditioning control system because of its low energy consumption and high efficient characteristics. ECV controls the entire vehicle air conditioning system by means of a pulse width modulation (PWM) system that supplied from an external controller. Different pressure ports located within ECV has important functions to control the air/refrigerant flow through its internal passages. The flow paths are preciously maintained with acceptable ranges of leakage (gap) between the parts inside it which is followed by effective design and critical dimensioning of its internal features. Therefore, it saves energy losses from the solenoid operation as well as ensures the balance of forces within it. The research paper highlights analysis of the leakages (at different pressure ports) and dimensioning tolerance factors that affects the ECV performance.

• Journal of electromagnetic engineering and science
• /
• 제1권1호
• /
• pp.11-17
• /
• 2001

In this paper, spherical Luneburg lens antennas have been systematically analyzed using the Eigenfunction Expansion Method (EEM), The developed technique has capability of performing a complete 3-D analysis to characterize the multi-layered dielectric spherical lens with arbitrary permittivity and permeability. This paper describes the analysis technique, and presents the results of the parametric study of Luneburg lens antennas by varying design parameters suoh as the diameter of the lens antenna (up to 80 wavelength), number of spherical shells (up to 30 shells), air-gaps between spherical shells, and dielectric loss of the material. Many representative engineering design curves including the far-field patterns, wide-angle sidelobe characterizations, antenna efficiency have been presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 A
• /
• pp.93-94
• /
• 2006

The sheath of a single-conductor cable for ac service acts as a secondary of a transformer, the current in the conductor induces a voltage in the sheath. When the sheaths of single-conductor cables are bonded to each other, as is common practice for multi-conductor cables, the induced voltage causes current to flow in the completed circuit. This current causes losses in the sheath. Various methods of bonding may be used for the purpose of minimizing sheath losses. In korea, sheath cross bonding system was employed for the prevention of sheath losses, the sheaths wire subjected to at voltages, and the bonding was designed to keep the magnitude of the induced voltages within small limits so as to prevent the possibility of sheath corrosion. But, sheath cross bonding system without transposition of cable can not achieve an exact balance of induced sheath voltages unless the cables are lain in trefoil. This paper describes a transposition system with sheath cross bonding using EMTP(Electromagnetic Transient Program). The transposition system with cross bonding can be extended to longer cable circuits for laid in flat as wall as trefoil by the methods described in this paper.

• 전기학회논문지
• /
• 제60권10호
• /
• pp.1846-1857
• /
• 2011

This paper deals with design and analysis of surface-mounted PM (SPM) motor for compressor of air-conditioning system for electric vehicle applications according to slot/pole combination. First, required torque-speed curve characteristics are determined from operating conditions of the compressor. Restricted conditions such as motor size limit and current density are also determined. And then, under same rated and restricted conditions, twelve models which have different slot/pole combinations each other are designed for various pole arc/pitch ratio using simple equations and 2-d finite element (FE) analyses. Designed models are analyzed and compared in terms of back-emf THD, cogging torque, torque ripple, power losses, efficiency, etc. On the basis of analysis results, it is found that the motor with a 6-pole PM rotor and a 27-slot stator has most outstanding performances in electromagnetic aspects. Finally, through the mechanical modal analysis and demagnetization analysis, it is concluded that the determined motor is most suitable for the compressor of air-conditioning system for electric vehicles.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.39-44
• /
• 2005

A broadband DC to 40 GHz 5-bit MMIC digital attenuator has been developed. The ultra broadband attenuator has been achieved by newly inserted the transmission lines in conventional Switched-T attenuator and the optimization of the transmission line parameters. Momentum was employed in design for an accurate performance prediction at high frequencies and Monte Carlo analysis was applied to verify performance stability against the MMIC process variation. The attenuator has been fabricated with 0.15 $\mu$m GaAs pHEMT process. This attenuator has 1 dB resolution and 23 dB dynamic range. High attenuation accuracy has been achieved over all attenuation range and full 40 GHz bandwidth with the reference state insertion loss of less than 6 dB at 20 GHz. The input and output return losses of the attenuator are better than 14 dB over all attenuation states and frequencies.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제2권1호
• /
• pp.33-37
• /
• 2002

Insulation aging diagnosis system provides early warning regarding electrical equipment defects. Early warning is very important in that it can avoid great losses resulting from unexpected shutdown of the production line. Since relations of insulation aging and partial discharge dynamics are non-linear. it is very difficult to provide early warning in an electrical equipment. In this paper, we propose the design method of insulation aging diagnosis system that use a electromagnetic wave and acoustic signal to diagnose an electrical equipment. Proposed system measures the partial discharge on-line from DAS(Data Acquisition System and acquires 2D patterns from analyzing it. For filtering the noise contained in sensor signals we used ICA algorithms. Using this data, we design of the neuro-fuzzy model that diagnoses an electrical equipment and is investigated in this paper. Validity of the new method is asserted by numerical simulation.

• 한국전자파학회논문지
• /
• 제11권3호
• /
• pp.410-418
• /
• 2000

본 논문에서는 27GHz에서 전파환경별 경로손실을 측정하고, 각 수신지점에서 5분간 측정된 경로손실 데이터의 중앙값, 최대값, 최소값을 선형회귀 모델로 모델링하고 분석하였다. 측정 결과를 살펴볼 때, 밀리미터파 대역 가시경로의 경우에도 도심이나 부심 환경에서는 추가의 경로손실을 고려해야 할 것으로 생각된다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.485-490
• /
• 2004

Flywheel Energy Storage System(FESS) consists of a high speed flywheel with an integral motor/generator suspended on non contact bearings and in an evacuated housing. Permanent magnet machines as the FESS motor/generator are a popular choice, since there are no excitation losses which means substantial increase in the efficiency. In this paper, the structural design method of rotor retainer for a high speed motor/generator are presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.954-956
• /
• 1993

This paper describes the process of levitation melting of metals in an axisymmetric induction heating system. This process has advantages of low heat losses, heating with short times and clean operating conditions. The shape of molten metal is determined using sensitivity analysis and optimization technique. Electromagnetic, gravitational and surface tension energies are considered, and these energies are used as an objective function in optimization process. Electromagnetic field are calculated using the finite element method. The fact that volume is constant in the process is also considered as an equality constraint.