• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.219-220
• /
• 2002

In this paper, we propose non-soldered current lead was introduced which has low contact resistivity for fault current limiters of YBCO film. Carbon/Cu has good thermal conductivity, electrical conductivity and chemically stable, and so forth. Therefore it seems to be suitable material of current lead for current limiters of YBCO film. We have investigated electric field-current in field of 0-130 mT and quench characteristics of a YBCO film. Experimental results show that characteristics of transport is all right using Carbon/Cu-current lead.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.813-815
• /
• 1998

In order to analyse the degradation process of epoxy/glass fiber for outdoor condition, FRP laminate was exposed to the wavelength of ultraviolet rays and evaluated by comparing contact angle, surface resistivity, surface potential decay, and ESCA spectrum respectively. Finally, We can conclude that the degradation phenomena on the surface of epoxy composites are dominated by the induction of ester and carboxyl groups.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1457-1459
• /
• 2001

This paper deals with the change of surface Potential decay, surface resistivity, contact an91e and XPS of ultraviolet-treated PET films. From the experimental results on the surface Potential decay of UV degraded-samples, it was found that the accumulation of charge is decreased and the surface potential decay time is shortened. Also, from the result of XPS, it was found that the changes affected by the surface degradation of PET film were caused by the generation of carboxyl groups through the chain decomposition and recombination with oxygen molecules in the air.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2000년도 제11회 정기총회 및 00년 동계학술발표회 논문집
• /
• pp.30-31
• /
• 2000

400DPI LED array was fabricated by using reactive ion etching(RIE) method. Material of fabricated LED array was used the GaP for green light emitting and had a homojunction structure. Each cells of emitting area in the LED array were defined with RIE etching for electrical isolation between cells. Electrodes were formed on each cells to emit independently. Ohmic contact resistivity was approximate 1.2$\times$10$^{5}$ $\Omega$/$\textrm{cm}^2$ and 1.26$\times$10$^{5}$ $\Omega$/$\textrm{cm}^2$ using isothermal annealing at 38$0^{\circ}C$ and 43$0^{\circ}C$. Emitting intensity of each etmitting cell was 1.65 cd/$m^2$.

• 센서학회지
• /
• 제22권3호
• /
• pp.197-201
• /
• 2013

This paper describes the fabrication and characterization of graphene based carbon dioxide ($CO_2$) gas sensors. Graphene was synthesized by thermal decomposition of SiC. The resistivity $CO_2$ gas sensors were fabricated by pure graphene and graphene decorated Au nanoparticles (NPs). The Au NPs with size of 10 nm were decorated on graphene. Au electrode deposited on the graphene showed Ohmic contact and the sensors resistance changed following to various $CO_2$ concentrations. Resulting in resistance sensor using pure graphene can detect minimum of 100 ppm $CO_2$ concentration at $50^{\circ}C$, whereas Au/graphene can detect minimum 2 ppm $CO_2$ concentration at same at $50^{\circ}C$. Moreover, Au NPs catalyst improved the sensitivity of the graphene based $CO_2$ sensors. The responses of pure graphene and Au/graphene are 0.04% and 0.24%, respectively, at $50^{\circ}C$ with 500 ppm $CO_2$ concentration. The optimum working temperature of $CO_2$ sensors is at $75^{\circ}C$.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.141-144
• /
• 2005

Sensing and interfacial evaluation of Ni nanowire strands/polymer composites were investigated using Electro-micromechanical technique. Electro-micromechanical techniques can be used as sensing method for micro damage, loading, temperature of interfacial properties. Using Ni nanowire strands/silicone composites with different content, load sensing response of electrical contact resistivity was investigated under tensile and compression condition. The mechanical properties of Ni nanowire strands with different type/epoxy composites were measured using uniformed cyclic loading and tensile test. Ni nanowire strands/epoxy composites showed humidity and temperature sensing within limited ranges, 20 vol% reinforcement. Some new information on temperature and humidity sensing plus loading sensing of Ni nanowire strands/polymer composites could be obtained from the electrical resistance measurement as a new concept of the nondestructive interfacial evaluation.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.298-303
• /
• 2000

We evaluated the electric properties of Bi-2223 jointed tapes processed by both resistive- and supercondcuting-joint methods. For the resistive-joint, filler materials of wood metal, Pb/Sn, In, and silver paste were used, whereas, for the superconductive-joint, the lap joint method were used. In the resistive-joint tape, it was observed that the electrical properties such as current transport property, n-value, and contact resistance of the tape were significantly related to the resistivity of filler materials. On the other hand, in the superconducting-joint tape, the current transport property was dependent on the uniaxial pressure. Specifically, the current transport property varied 50 to 80% with uniaxial pressure, probably due to the irregular microstructure in the transition region.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권10호
• /
• pp.465-472
• /
• 2002

This paper presents a study on the aging and recovery of HTV (high temperature vulcanized) silicone rubber used for outdoor insulators. UV irradiation, corona discharge and water immersion were employed as factors of the artificial aging. The effects of changes derived from these stresses on the tracking and arc resistance of silicone rubber were examined. We have investigated the aging phenomena of HTV silicone rubber by the above stresses using the surface energy calculation with contact angle measurement, solvent-extraction, and surface/volume resistivity and so on. These results showed that UV irradiation and corona discharge lead to nearly the same surface oxidation, but the percentage change of mobile low molecular weight by these stresses was different. Furthermore, the oxidized layer induced under UV irradiation restricted the recovery of hydrophobic surface. Water immersion little lowered hydrophobicity level and leaded to a loss of tracking and arc resistance. The degradation mechanism based on our results was discussed.

• E2M - 전기 전자와 첨단 소재
• /
• 제7권3호
• /
• pp.243-251
• /
• 1994

ITO(Indium Tin Oxide) film with thickness of 1500.angs. was prepared by an e-beam evaporator onto a glass and a p-type InP wafer (100) LEC grown Zn-doped p=2.3*10$\^$16/cm$\^$-3/), in which the components of ITO used for evaporation source were hot pressed pellets 1 mole% ln$\_$2/O$\_$3/+9 mole% SnO$\_$2/, and evaporated in O$\_$2/ ambient. The optimum conditions to preparation of ITO thin film were the substrate temperature of 350.deg. C, the injected oxygen pressure of 2*10$\^$-4/ torr, and the evaporation speed of 0.2-0.3.angs./sec, respectively. In these optimum conditions, the resistivity and the carrier concentration were 5.3*10$\^$-3/ .ohm.-cm, 6.5*10$\^$20/cm$\^$-3/, and the transmittance was over 80%. From the results of J-V measurements in ITO/p-InP structure solar cells, the higher pressure of injected oxygen, the more open circuit voltage. The efficiency of ITO/p-InP solar cell without the grid line contact, prepared by the optimum evaporation conditions, was 7.19%. By using the grid line contact, the efficiency, the open circuit voltage, the short circuit current density, the fill factor, the series resistance, and the shunt resistance were 8.5%, 0.47V, 29.48 mAcm$\^$-2/ , 61.35%, 3.ohm., and 26.6k.ohm., respectively.

• 한국세라믹학회지
• /
• 제39권2호
• /
• pp.120-125
• /
• 2002

AC powder EL 소자를 절연층의 유전재료와 후면전극의 전기비저항을 변화시켜 스크린 프린팅법으로 제조하였다. 제조된 소자의 광전기적 특성을 평가하기 위하여 인가 전압은 50∼300 $V_{rms}$까지 변화시켜 휘도 및 전류밀도를 측정하였다. 주파수 및 전압공급원은 정현파 발생 장치로서 frequency generator를 이용하였다. 휘도는 luminometer 의해 측정되었으며 전류밀도 측정을 위하여 multimeter를 사용하였다. 또한 유전층에 대한 유전율을 후막 제조 후 impedance analyser(HP 4194 A)를 이용하여 측정하였다. $TiO_2$ 분말을 $BaTiO_3$에 첨가함에 따라 유전율의 향상으로 초저가형 AC powder EL 소자의 유전층에 적용함으로써 거의 비슷한 전류밀도 하에 50 cd/$m^2$ 정도의 향상된 휘도를 얻을 수 있었다. 저전력 소모형 AC powder EL 소자의 유전층에 적용시 상용분말을 이용한 경우보다 용액 연소법에 의해 제조된 $BaTiO_3$ 분말을 이용한 경우가 더욱 향상된 85 cd/$m^2$ 정도의 휘도를 얻을 수 있었다. 또한 후면전극의 전기 비저항을 조절함으로써 AC powder EL 소자의 휘도는 비교적 감소하지만 전류밀도를 낮출 수 있었다.