• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.10
• /
• pp.8-19
• /
• 2019

In this study, the spray pattern of a centrifugal fertilizer distributor with two shutter holes was analyzed and an effective driving width that satisfies proper spray uniformity was derived. The centrifugal fertilizer distributor was mounted on a tractor with a rated power of 23.7 kW and static and dynamic spray pattern tests were performed according to the standard procedure proposed by the American Society of Agricultural and Biological Engineers Standard ASAE S341.5. The height of the fertilizer distributor was 80 cm from the ground and the PTO (power take-off) shaft speed of the tractor was fixed at 540 rpm. The fertilizer scattered in space was collected using 275 evenly spaced collectors at shutter opening ratios of 25%, 50%, 75%, and 100%. The spray pattern was analyzed via the amount of sprayed fertilizer at each collector location and the coefficient of variation was used as an indicator of spray uniformity. Using the analyzed spray pattern, the effective driving width that satisfied less than 15% of the coefficient of variation was derived for different tractor driving patterns (race track mode, back and forth mode). From the results, spray uniformity increased as the shutter opening ratio decreased. The largest effective driving width was 8 m at a shutter opening ratio of 25% for both driving patterns.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.11
• /
• pp.575-580
• /
• 2001

In this paper, using $500\mum-thickness\; (100)\; silicon\; wafer,\; flat\; 65\mum-thickness$ silicon mirror plates were fabricated through dry etching and wet etching, and $45\mum-depth$ grooved driving electrodes were fabricated through UV-LIGA process. Four shapes of the driving electrode were fabricated: twenty four grooves of the $50\mum-width$, twelve grooves of the $100\mum-width$, six grooves of the $200\mum-width$, and no grooves on the driving electrode. Fabricated mirror plate size and spring size are $2400\times2400\times65\mum3\; and \;500\times10\times65\mum3,$ respectively. Mirror plate parts and driving electrodes were assembled into the scanning mirrors. Measured natural resonance frequencies were about 600Hz which have error within $\pm 2%$ to calculated value. Due to the squeeze effect in the narrow gap between the mirror plate and the driving electrode, measured resonance frequencies were reduced as raising the amplitude of the mirror plate. In a case of driving electrode without grooves, the resonance frequency was reduced largely, compared with a case of driving electrode with grooves. According to the experimental results, squeeze effect was smaller in the driving electrode with smaller-width and many grooves. Therefore, the driving electrode with smaller-width and many grooves was effective in low voltage and high speed operation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.7
• /
• pp.919-928
• /
• 2010

Four patterns for width adjustment were studied with an aim to increase the width-adjustment speed in continuous casting. The main goals are to minimize the actuating force of a WAM actuator, to develop a deformation analysis model of a solidified shell in the mold, and to induce the main limit factor for the speedup of width adjustment. On the basis of the width-adjustment experiment, the notable features of four patterns types were considered, and we compared the corresponding actuating forces. For comparing the driving forces of the patterns, during the experiment, the same casting speed was maintained for each pattern. To optimize the parameter of the deformation analysis model of the solidified shell, the experiment results were applied to them. To speed up width adjustment and to reduce the driving force, we controlled the pattern parameters. The most effective pattern was the fast-mode pattern, and the taper was the main parameter that helped reduce the driving forces during the motion of the actuator.

• Journal of Sensor Science and Technology
• /
• v.27 no.6
• /
• pp.421-426
• /
• 2018

To develop a piezoelectric inkjet printhead for high-resolution and high-speed printing, we studied the characteristics of an inkjet printhead by analyzing the major design parameters. An analytical model for the inkjet printhead was established, and numerical analysis of the coupled first-order differential equation for the defined state variables was performed using state equations. To design the dimension of the inkjet printhead with a driving frequency of 100 kHz, the characteristics of the flow rate and discharge pressure of the nozzle were analyzed with respect to design variables of the flow chamber, effective sound wave velocity, driving voltage, and voltage waveform. It was predicted that the change in the height of the flow chamber does not significantly affect the Helmholtz resonance frequency and discharge speed of the nozzle. From the analysis of change in flow chamber width, it is observed that as the width of the flow chamber increases, the ejection speed greatly increases and the Helmholtz resonance frequency decreases considerably, thereby substantially affecting the performance of the inkjet printhead.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2851-2854
• /
• 2003

The purpose of this paper was to find out the stabilized and effective value of RC-parameter by using PSpice simulation, considering that gate signal voltage can be distorted by RC-delay of signal line. the results of this study were as follows: TFT-LCD with high quality resolution increased the number of gate signal line and this made TFT on-time shorter over-width of signal line to improve the performance of TFT made the electrostatic capacity increase and the time constant higher, making problems and errors. and owing to the decrease of the aperture ratio, an electro optic character of LCD, we must consider the capacity and the condition of production process in deciding the width and the thickness of the gate signal line.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.455-455
• /
• 2000

A novel pulse-width-modulated (PWM) function is introduced for precise position measurement in an enclosed signal field. An amplitude modulation was used to light the LEDs for the conventional study. However, the transform properties from the driving signal to the lighting intensities of the LEDs are non-linear, and accurate control of the lighting power was necessary. Therefore, a lighting function independent of these properties is desired. Well-known PWM functions are used to construct the enclosed signal field by simulation, and the precision of the phase detecting system is analyzed. A novel "axial symmetry PWM" function is found to be effective for orthogonal pahse detection.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.335-339
• /
• 2001

The recent advancements in power electronic switching devices have enabled high frequency switching operation and have improved the performance of pulse-width modulated (PWM) inverters for driving induction motors. But, the insulation failures of stator winding have attracted much concern due to high dv/dt of IGBT PWM inverter. In this paper, the test results for evaluation on the stator winding insulation of low-voltage induction motors for IGBT PWM inverter applications are presented. The insulation characteristics are analyzed with partial discharge and dissipation factor tests. Also, insulation breakdown tests by switching pulse voltage are performed. An effective insulation technique to enhance the insulation strength is suggested from the test results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.2
• /
• pp.17-22
• /
• 2003

The priming discharge characteristic at the reset period in the ADS drive method of PDP was experimentally analyzed in this research. The amount of wall charge accumulated by the discharge and the accumulated time are unrelated to the priming pulse width. The self-erase discharge by excessive wall charge is related to the amount of wall charge by the priming discharge and this is related to space charge generated by the priming discharge. From the experimental result, in the optimized priming condition the plus width is 8$mutextrm{s}$ and the voltage is about 163V. The space charge which helps the self-erase discharge exists during about 16$mutextrm{s}$ immediately after generating the priming discharge. Therefore, it is suitable within 16$mutextrm{s}$ of the priming pluse width for the effective reset process.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.4
• /
• pp.39-46
• /
• 2005

This research concerns the ADS drive method of 3 electrodes AC PDP and is determined the minimum pulse width of the address and the sustain, which the steady sustain discharge without decreasing luminance can be obtained. From the experimental result, if the address pulse width became $1.5[{\mu}s]$ or more a effective address discharge with the operating margin of 35[V] was possible. And if the sustain pulses width became $2[{\mu}s]$ or more, a steady sustain discharge with the operation margin of 25[V] was possible. When this condition is applied to Full-HDTV class PDP with the in lines of horizontal scanning lines, 8 sub-fields and total 1420 sustain pulses can be used.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.5
• /
• pp.302-305
• /
• 2016

In this paper, a low on-resistance and high current driving capability trench gate power metal-oxide-semiconductor field-effect transistor (MOSFET) incorporating a current sensing feature is proposed and evaluated. In order to realize higher cell density, higher current driving capability, cost-effective production, and higher reliability, self-aligned trench etching and hydrogen annealing techniques are developed. While maintaining low threshold voltage and simultaneously improving gate oxide integrity, the double-layer gate oxide technology was adapted. The trench gate power MOSFET was designed with a 0.6 μm trench width and 3.0 μm cell pitch. The evaluated on-resistance and breakdown voltage of the device were less than 24 mΩ and 105 V, respectively. The measured sensing ratio was approximately 70:1. Sensing ratio variations depending on the gate applied voltage of 4 V ~ 10 V were less than 5.6%.