• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.233-234
• /
• 2008

Radiation characteristics of a microstrip patch antenna integrated with a UC-EBG (Uniplanar Compact Electromagnetic Bandgap) structure and a Mushroom EBG structure are compared. Radiation characteristics of a patch antenna integrated with a Mushroom EBG structure are better than those of a patch antenna integrated with a UC-EBG structure.

• ETRI Journal
• /
• v.38 no.5
• /
• pp.903-910
• /
• 2016

We propose a novel multi-stack (MS) technique for a compact and wideband electromagnetic bandgap (EBG) structure in high-speed multilayer printed circuit boards. The proposed MS technique efficiently converts planar EBG arrays into a vertical structure, thus substantially miniaturizing the EBG area and reducing the distance between the noise source and the victim. A dispersion method is presented to examine the effects of the MS technique on the stopband characteristics. Enhanced features of the proposed MS-EBG structure were experimentally verified using test vehicles. It was experimentally demonstrated that the proposed MS-EBG structure efficiently suppresses the power/ground noise over a wideband frequency range with a shorter port-to-port spacing than the unit-cell length, thus overcoming a limitation of previous EBG structures.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.8
• /
• pp.933-939
• /
• 2008

In this paper, a new composite electromagnetic bandgap(EBG) structure using magnetic materials is proposed for simultaneous switching noise(SSN) suppression in the high-speed digital circuits. The proposed EBG structure has periodic unit cells of square-patches connected by spiral-shaped bridges. The magnetic materials are located on the unit cells of spiral-shaped EBG. The real part of the permeability shifts bandgap to the lower frequency region due to the increased effective inductance. The imaginary part of the permeability has magnetic loss that decreases parasitic LC resonance peaks from between the unit cells. As a result, the proposed structure has the lower cut-off frequency compared with conventional EBG structure and -30 dB SSN suppression bandwidth from 175 MHz to 7.7 GHz. The proposed structure is expected to improve the power integrity and reduce the size of the EBG power plane.

• ETRI Journal
• /
• v.35 no.5
• /
• pp.827-837
• /
• 2013

In this paper, we present wideband common-mode (CM) noise suppression using a vertical stepped impedance electromagnetic bandgap (VSI-EBG) structure for high-speed differential signals in multilayer printed circuit boards. This technique is an original design that enables us to apply the VSI-EBG structure to differential signals without sacrificing the differential characteristics. In addition, the analytical dispersion equations for the bandgap prediction of the CM propagation in the VSIEBG structure are extracted, and the closed-form expressions for the bandgap cutoff frequencies are derived. Based on the dispersion equations, the effects of the impedance ratio, the EBG patch length, and via inductances on the bandgap of the VSI-EBG structure for differential signals are thoroughly examined. The proposed dispersion equations are verified through agreement with the full-wave simulation results. It is experimentally demonstrated that the proposed VSI-EBG structure for differential signaling suppresses the CM noise in the wideband frequency range without degrading the differential characteristics.

• Journal of information and communication convergence engineering
• /
• v.14 no.4
• /
• pp.252-257
• /
• 2016

An edge-located electromagnetic bandgap (EL-EBG) structure using a defected ground structure (DGS) is proposed to suppress resonant modes induced by edge excitation in a two-dimensional planar parallel plate waveguide (PPW). The proposed EL-DGS-EBG PPW significantly mitigates multiple transverse-magnetic (TM) modes in a wideband frequency range corresponding to an EBG stopband. To verify the wideband suppression, test vehicles of a conventional PPW, a PPW with a mushroom-type EBG structure, and an EL-DGS-EBG PPW are fabricated using a commercial process involving printed circuit boards (PCBs). Measurements of the input impedances show that multiple resonant modes of the previous PPWs are significantly excited through an input port located at a PPW edge. In contrast, resonant modes in the EL-DGS-EBG PPW are substantially suppressed over the frequency range of 0.5 GHz to 2 GHz. In addition, we have experimentally demonstrated that the EL-DGS-EBG PPW reduces the radiated emission from -24 dB to -44 dB as compared to the conventional PPW.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.3 s.94
• /
• pp.300-310
• /
• 2005

In this paper we propose the compact three-layer EBG structure. The unit cell of the proposed EBG structure is composed of a square patch in the upper layer and a square ring stripline in the lower layer that are connected to the ground plane through conducting vias. Reflection phase analysis method and tangential transmission method were considered to accomplish effective EM simulation and measurement. EM simulation results indicate that bandgap characteristics of the EBG structure using both methods is nearly identical. Parametric studies have been performed with the EM simulator to analyze the properties of the EBG structure by investigating the phase shift of the normally incident plane wave, and the transmission measurements between simple monopole antennas positioned near the EBGstructure have been done. The operating fiefuency bandgap of the proposed EBG structure is about 34 $\%$ lower than the conventional EBG structure with the same size. Measured results show bandgap from 0.930 GHz to 0.945 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.7 s.349
• /
• pp.162-169
• /
• 2006

A Micorstrip Bandpass Filter Using DBRs for WLAN ($2.3{\sim}2.4GHz$) applications is designed and an EBG structure is employed in the ground plane of the filter to suppress the stopband responses of the filter. The number of DBRs is chosen as two in consideration of low insertion loss and small size of two filter. The center frequency of the filter to be designed is 2.35GHz and its bandwidth is 140MHz. The responses of two kinds of DBR filters (one with EBG and the other without EBG) are calculated and compared with the measurements. The experimental results are in good agreement with the calculations: The bandwidth and insertion loss of the filter with EBG structure are 3.8% and 1.7dB respectively, while those of the filter without EBG structure are 7% and 1.23dB. It is shown that the insertion loss of the filter is increased and its bandwidth is deceased due to the EBG structure. Also the stopband responses of the filters with EBG structures are shown to be much improved compared with those without EBG.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.306-313
• /
• 2012

In order to enhance the isolation level between two dual-band E-slot microstrip patch antennas, EBG structure which operates in UMTS Tx(1.92~1.98 GHz) and Rx(2.11~2.17 GHz) band is proposed. The proposed EBG structure made with a periodic array of two different size EBG unit cells which has a modified mushroom-type for isolation improvement between two antennas. They do not share a common ground plane of the microstrip patch antenna. Overall size of the fabricated antenna is $210.5mm{\times}117mm$. The two different EBG unit cell sizes are $15.6mm{\times}4mm$ and $17.4mm{\times}4mm$, respectively. It was etched on the FR-4 substrate(thickness=3.93 mm, ${\varepsilon}_r$=4.6). The experiment results show that the isolation level between antennas in Tx/Rx band were improved by about 9 dB and 12 dB, respectively, through the use of the proposed EBG structure.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.1
• /
• pp.78-81
• /
• 2015

This paper investigates the performance of phone case with different permittivities like plastic, urethane and silicone. Then, we put an electromagnetic band gap (EBG) structure in phone case to reduce the specific absorption rate (SAR). In order to design the phone case, a loop antenna for PCS 1900 band was used. The phone case consists of a hairpin-like EBG structure that is more compact than other EBG structures. The SEMCAD X fdtd simulation results showed that, this proposed phone case can reduce SAR by 13 - 30% at similar power that is radiated by the antenna. This phone case can be used in future to reduce the SAR from mobile phones.

• Journal of Satellite, Information and Communications
• /
• v.9 no.4
• /
• pp.42-46
• /
• 2014

In this paper, a coil typed electromagnetic band gap (EBG) structure to be inserted in the printed circuit board (PCB) inner layer in order to stabilize the PCB power line is proposed and implemented for global-navigation satellite service (GNSS) with the bandwidth from 1.55GHz to 1.81GHz. From the measurement result of the PCB board including EBG structure, the insertion loss(S21) was measured below about -50dB. From these results, it is expected that the stabilization of power delivery network (PDN) structure in the PCB circuit design should be improved and the preparation to EMI will be effective.