• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.4_2
• /
• pp.467-474
• /
• 2021

The renewable energy is known as eco-friendly energy to reduce the use of fossil fuel and decrease the environmental pollution due to exhaust gas. Targets of solar collector in domestic are usually acquisitions of hot water and hot air. System of air-heating collector is one of the technologies for obtaining hot air in cases of especially heating room and drying agricultural product. The purpose of this study is to investigate the characteristics of thermal flow such as relative pressure, velocity, outlet temperature and buoyancy effect in air-heating collector using solar heat. The flow field of air-heating collector was simulated using ANSYS-CFX program and the behaviour of hot air was evaluated with SST turbulence model. As the results, The streamline in air-heating collector showed several circular shapes in case of condition of buoyancy. Temperature difference in cross section of outlet of air-heating collector did not almost show in cases of buoyancy and small inlet velocity. Furthermore merit of air-heating collector was not observed in cases of inlet velocities. Even though it was useful to select condition of buoyancy for obtaining high temperature, however, it was confirmed that the trade off between high temperature of room and rapid injection of hot air to room could be needed through this numerical analysis.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.422.1-422.1
• /
• 2016

Graphene quantum dots (GQDs), a new kind of carbon-based photo luminescent nanomaterial from chemically modified graphene oxide (CMGO) or chemically modified graphene (CMG), has attracted extensive research attention in the last few years due to its outstanding chemical, optical and electrical properties. To further extended its potential applications as optoelectronic devices, solar cells, bio and bio-sensors and so on, intensive research efforts have been devoted to the CMG. However, the CMG, a suspension of aqueous, have problematic since they are prone to agglomeration after drying a solvent. In this study, we synthesized the GQDs from graphite and deposited on silicon substrate by kinetic spray. The photo luminescent properties of deposited GQD films were analyzed and compared with initial GQDs suspension. In addition, its carbon properties were investigated with GQDs solution properties. The properties of deposited GQD films by kinetic spray were similar to that of the GQDs suspension in water. We could provide a pathway for silicon-based silicon based device applications. Finally, the well-adjusted GQD films with photo luminescence effects will show Energy-Down-Shift layer effects on silicon solar cells. The GQD layers deposited at nozzle scan speeds of 40, 30, 20, and 10 mm/s were evaluated after they were used to fabricate crystalline-silicon solar cells; the results indicate that GQDs play an important role in increasing the optical absorptivity of the cells. The short-circuit current density (Jsc) was enhanced by about 2.94 % (0.9 mA/cm2) at 30 mm/s. Compared to a reference device without a GQD energy-down-shift layer, the PCE of p-type silicon solar cells was improved by 2.7% (0.4 percentage points).

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.715-725
• /
• 1996

This study represents the synthetic characteristics of styrene-DVB copolymer which is used as a catalyst support for the removal of tritium in CANDU. To evaluate the effect of solvent on the styrene-DVB polymeric support, the solvating power dependent on various kinds and composition of solvents was calculated. In order to synthesize the macroreticular type polymer bead, the following conditions are needed; solvating power should be higher than 1 for 20% of crosslinkage and higher than 3 for 40% of crosslinkage. Stabilization of organic monomers at about $40^{\circ}C$ for more than 2 hours is prerequisite. Removal of solvent prior to drying is preferred for the post-treatment of the bead. The polymer particle size was increased by lowering concentration of surfactant and stirring speed.

• Journal of Hydrogen and New Energy
• /
• v.28 no.5
• /
• pp.471-480
• /
• 2017

A proton exchange membrane fuel cell (PEMFC) operated at $150^{\circ}C$ was evaluated by a controlling different amount of phosphoric acid (PA) to a membrane-electrode assembly (MEA) without humidification of the cells. The effects on MEA performance of the amount of PA in the cathode are investigated. The PA content in the cathodes was optimized for higher catalyst utilization. The highest value of the active electrochemical area is achieved with the optimum amount of PA in the cathode confirmed by in-situ cyclic voltammetry. The current density-voltage experiments (I-V curve) also shows a transient response of cell voltage affected by the amount of PA in the electrodes. Furthermore, this information was compared with the production variables such as hot pressing and vacuum drying to investigate those effect to the electrochemical performances.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.1
• /
• pp.9-15
• /
• 2011

The composite membranes comprising of sulfonated polymers as matrix and ionic liquids as ion-conducting medium in replacement of water are studied to investigate the effect of annealing of the sulfonated polymers. The polymeric membranes are prepared on recast Nafion containing the ionic liquid, 1-ethyl-3-methylimidazolium tetrafluoroborate ($EMIBF_4$). The composite membranes are characterized by thermogravitational analyses, ion conductivity and small-angle X-ray scattering. The composite membranes annealed at $190^{\circ}C$ for 2 h after the fixed drying step showed better ionic conductivity, but no significant increase in thermal stability. The mean Bragg distance between the ionic clusters, which is reflected in the position of the ionomer peak (small-angle scattering maximum), is larger in the annealed composite membranes containing $EMIBF_4$ than the non-annealed ones. It might have been explained to be due to the different level of ion-clustering ability of the hydrophilic parts (i.e., sulfonic acid groups) in the non- and annealed polymer matrix. In addition, the ionic conductivity of the membranes shows higher for the annealed composite membranes containing $EMIBF_4$. It can be concluded that the annealing of the composite membranes containing ionic liquids due to an increase in ion-clustering ability is able to bring about the enhancement of ionic conductivity suitable for potential use in proton exchange membrane fuel cells (PEMFCs) at medium temperatures ($150-200^{\circ}C$) in the absence of external humidification.

• Membrane Journal
• /
• v.23 no.5
• /
• pp.367-374
• /
• 2013

In the present study, Pebax-2533 plate membranes were prepared by drying precursor solutions which were obtained by dissolving Pebax-2533 polymer in 1-Propanol/n-Butanol mixed solvents. And then the $CO_2$ and $N_2$ permeation behaviors were tested by using a time-lag system. The prepared Pebax-2533 plate membranes showed a considerable $CO_2/N_2$ separation performance : the $CO_2$ permeability was 130 to 288 barr, and the $CO_2/N_2$ permselectivity was 5-8. The $CO_2$ permeation data obtained by varying feed pressure, permeation temperature, and solvent composition announced that not only the $CO_2$ sorption but also the $CO_2$ diffusion is equally important in the overall $CO_2$ permeation.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.29 no.3
• /
• pp.223-228
• /
• 2023

Sustainable energy supplies without the recharging and replacement of the charge storage device have become increasingly important. Among various energy harvesters, the triboelectric nanogenerator (TENG) has attracted considerable attention due to its high instantaneous output power, broad selection of available materials, eco-friendly and inexpensive fabrication process, and various working modes customized for target applications. In this study, the amount of voltage and current generated was measured by applying the PSD profile random vibration test of the electronic vibration tester and ISTA 3A according to the time of Anodized Aluminum Oxide (AAO) pore widening of the manufactured TENG device Teflon and AAO. The discharge and charging tests of the integrated module during the random simulated transport environment and the recognition distance of RFID were measured while agricultural products (onion) were loaded into the returnable folding plastic box. As a result, it was found that AAO alumina etching processing time to maximize TENG performance was optimal at 31 min in terms of voltage and current generation, and the integrated module applied with the TENG module showed a charging effect even during the continuous use of RFID, so the voltage was kept constant without discharge. In addition, the RFID recognition distance of the integrated module was measured as a maximum of 1.4 m. Therefore, it was found that the surface condition of AAO, a TENG element, has a great influence on the power generation of the integrated module, and due to the characteristics of TENG, the power generation increases as the surface dries, so it is judged that the power generation can be increased if the surface drying treatment (ozone treatment, etc.) of AAO is applied in the future.

• Journal of the Korean Ceramic Society
• /
• v.16 no.4
• /
• pp.213-224
• /
• 1979

The present work was undertaken: (1) to determine if CaO-partially stabilized $ZrO_2$ prepared by Hot Petroleum Drying Method would show better ionic conductor as an oxygen sensor in molten metals than that prepared by Oxide Wet Mixing Method and than CaO-fully stabilized $ZrO_2$, and (2) to understand the nature of conduction mechanism of CaO-partially stabilized $ZrO_2$ by a comparison of measured electrical conductivity data with theory on defect structure of pure monoclinic $ZrO_2$ and fully stabilized cubic $ZrO_2$. The DC electrical conductivity was measured by 3-probe technique and the AC electrical conductivity by 2-probe technique as a function of temperature in the range 973-1373 K and oxygen partial pressure in the range 10-1-10-25Mpa. The results of the experiments were as follows: 1. CaO-partially stabilized $ZrO_2$ prepared by Hot petroleum Drying Method showed at T=1094-1285 K and $Po_2$=10-7-10-25 MPa a nearly ionic conduction with 4 times higher conductivity than that prepared by Oxide Wet Mixing Method. 2. High-oxygen pressure conductivity tends toward a Po_2^{+1/5}-Po_2^{+1/6}$dependence. An analysis of possible defect structures suggests that CaO-partially stabilized $ZrO_2$ has an anti-Frenkel defect in which singly or doubly ionized oxygen interstitials and defect electrons predominate at T=1094-1285 K and $Po_2$=10-1-10-7MPa. 3. The activation energy for pure electron hole-conduction and ionic conduction of CaO-partially stabilized $ZrO_2$ was found to be 130 KJ/mol at T=973-1373 K, $Po_2$=2, 127 10-2 MPa(air) and 153KJ/mol at T=1094-1285 K respectively.

• Biomedical Science Letters
• /
• v.9 no.4
• /
• pp.195-201
• /
• 2003

Aromatic hydrocarbons are of major concern among genotoxic chemicals due to their toxicity and persistence. Some microorganisms can utilize aromatic hydrocarbons as carbon and energy sources by inducing expression of catabolic operon(s). The XylR regulatory protein activates transcription of the catabolic enzymes to degrade BTEX (benzene, toluene, ethylbenzene, and xylene) from its cognate promoters, Pu and Ps upon exposure of the cells to the aromatic hydrocarbons. The activity of XylR on the promoters was previously monitored using luciferase luc reporter system. The xylR, its promoter Pr and the promoter Po for the phenolic compound catabolic operon were introduced upstream of firefly luciferase luc in the pGL3b vector to generate about 7.1 kb of pXRBTEX. Here E. coli harboring the plasmid was freeze-dried under various conditions to fin,d optimal conditions for storage and transport. The cell viability and luciferase activity were maintained better, when the cells were freeze-dried at -7$0^{\circ}C$ in the addition of the 10% skim milk or 12% sucrose. However, coaddition of protectants such as 10% skim milk plus 10% glucose or 12% sucrose plus 10% glucose, resulted in much better viability and bioluminescence activity compared with the effect of single addition of each protectant. In addition, it was shown that the freeze-dried cells maintained almost intact bioluminescent activities and cell viability for at least 1 week after freeze-drying. This work demonstrated that the properly freeze-dried recombinant bacterial cells could be utilized as a whole-cell biosensor for simple and rapid monitoring of BTEX in the environment.

• Journal of the Korean Magnetics Society
• /
• v.7 no.6
• /
• pp.314-320
• /
• 1997

We have observed the orientation behavior of acicular iron oxides in magnetic layer of the particular magnetic tape after magnetic paint was coated on polyester film. As results of the static orientation, orientation of iron oxides come to the maximum at the front and the back of orientation magnets, but it was a litter lower at the back than at the front, and it slowly decreases and come to the constant level after passing through the orientation magnets. In case of edge portion to be futher away from center in the coated film, the orientation of iron oxides in magnetic layer come to worse than that of the center. We think it is owing to the shape and the magnetic magnitude of orientation magnets. The results of the dynamic orientation are as follows. As the orientation of iron oxides in the particulated magnetic tape is higher, the output properties of tape come to better than ever. And the orientation of iron oxides can be changed by drying condition, as result, the output properties of tape can be also. Therefore we think the considrations of the design of orientation magnets and the control of drying condition are needed to improve output properties of the particulated magnetic tape.