• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.69-70
• /
• 2006

Waste vinyl tretreatment system has been developed by the joint project between KIMM and Woosung Co. General process for removal of impurities from waste vinyl is consisted of feeding, separating, cutting, washing, drying and recovering impurities. However, there are problems such as wastewater when washing of waste vinyl. In order to solve these problems we have developed new dry type cleaning system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1769-1770
• /
• 2007

To prevent an insulator failure, an automatic cleaning robot was developed for suspension insulator strings. The robot autonomously moves along the insulator string using the clamps installed on its two moving frames, and adopts a dry cleaning method using rotating brushes and a circular motion guide. In addition, a mechanized brush bristles and a voltage-balancing contactor are devised to increase cleaning efficiency and to prevent arc generation under live-line conditions, respectively. Moreover, a manual tool for its installation and removal is presented. We confirmed its effectiveness through experiments.

• 한국생활과학회지
• /
• 제6권2호
• /
• pp.115-120
• /
• 1997

To investigate the cognition of labeling system and its problems, problems in laundry, and consumer's dissatisfaction and to decrease problems in management of clothing products, total 476 subjects were surveyed in Taejon. The major results were as follows ; 1. The cognition of labeling system was understood by 93.1% of respondents, and 72.9% of them prefer to recognized labeling by figures and letters than by either of them. Most of respondents got the knowledge of labeling system from school. The most frequently experienced mislabeling was the label for management. 2. In cleaning, 60.4% of respondents made their decisions of the laundry method after seeing labeling system. When the label recommanded either of hand washing or dry cleaning, they usually laundered with hand washing after a few times of dry cleaning. The first consideration factor for laundry was fiber composition of textiles. 3. About 70% of respondents understood ironing, laundry, and drying mark on labeling system, and 53.8% understood fiber composition and bleaching. 4. More than 90% of respondents experienced dissatisfaction in handling clothing products. The reason of dissatisfaction was deformation and decoloring after laundry. Most of respondents experienced change of tactile sensation, too.

• 한국식품조리과학회지
• /
• 제24권5호
• /
• pp.706-712
• /
• 2008

This study was conducted to evaluate the sanitation level and use of dish cloths, chopping board, and drawer in the refrigerator in 50 university students' houses located in Seoul and Kyonggido. The survey questionnaire evaluated general information, frequency of the washing, cleaning method, drying method and the associated factors. The highest percentage of the cleaning and drying methods of dish cloths were “boiling(76.0%)”, and “dry in the kitchen or on the sink(78.0%)”, respectively. For the chopping board and drawer in the refrigerator, the highest percentage of cleaning method was “use detergent” and drying method was “dry in the kitchen”. The mean of coliforms for dish cloths, chopping board, and drawer in the refrigerator was 4.46${\pm}$1.95 log CFU/100 $cm^2$, 3.92${\pm}$1.64 log CFU/100 $cm^2$, 3.48${\pm}$2.01 log CFU/ 100 $cm^2$, respectively. Salmonella spp. were not detected from all samples. But E. coli were detected from dish cloths(4.0%) and S. aureus were detected from dish cloths(16.0%), chopping board(12.0%), and drawer in the refrigerator(8.0%). The results of microbiological test of kitchen utensils indicated that the sanitary conditions of dish cloths, chopping board, drawer in the refrigerator should be improve promptly.

• 반도체디스플레이기술학회지
• /
• 제23권2호
• /
• pp.100-106
• /
• 2024

To generate the plasma required in dry cleaning processes, the plasma chamber must be supplied with a high-quality AC voltage with a voltage of more than 1 kV and a frequency of 400 kHz. In the existing research, many methods to supply high power have been studied, but how to improve the quality of the power for high-quality plasma has been relatively little studied. In this paper, we propose a study to improve the quality of RF power circuit for high-quality plasma generation in dry cleaning method. Existing methods in the environment of full-bridge-based RF power circuits must perform PWM duty control in the light load region. This causes distortions in the waveform, resulting in poor power quality, which directly leads to poor plasma quality. To solve these problems, a half-bridge switching method is proposed and the improvement in waveform quality is verified. To verify the feasibility of the design and control algorithm proposed in this paper, an RF power circuit prototype is fabricated and the proposed design and control method is verified through simulation and actual experiments under dummy load.

• 복식문화연구
• /
• 제12권3호
• /
• pp.407-414
• /
• 2004

A natural dye aqueous walnut shell extract was obtained by extraction of walnut shell using water at various conditions in this study. Silk fabrics were dyed at various dyeing and mordanting conditions using walnut shell extract and various mordants (Al, Cu, Fe ions). Studies have been made on the effects of dyeing and mordanting conditions on the dyeing properties and fastness (light, water and dry cleaning fastness) of dyed silk Fabric. The results obtained in this study were as follows;. The dye content in the walnut shell extract increased with increasing extraction temperature to 90℃ and extraction time to 120min, and thereafter the dye content decreased a little. The dry cleaning and water fastness of non-mordanted silk fabrics were better than those of mordanted silk fabrics.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.256-259
• /
• 2003

To develop cleaning process various particles should be deposited on wafer surfaces to measure particle removal efficiencies. The purpose of the article in to evaluate, removal efficient)r of silica and alumina particles from wafer surfaces when they are deposited by dry and wet method. Dry deposition in air and wet spray deposition using solutions are used. van der Waals are considered to calculate the adhesion force of particles on surfaces. Higher adhesion force is measured on alumina particles on silicon when particles are deposited in air.

• 한국의류학회지
• /
• 제27권9_10호
• /
• pp.1134-1143
• /
• 2003

The purpose of this study is to investigate surface color change and effects of mordants on the K/S values of silk and wool fabrics dyed with Lac extract, according to the mordanting methods and conditions such as temperature, concentration and time of the mordanting bath. The results were as follow; 1 K/S values of the silk and wool fabrics according to the temperature of the mordanting bath were shown a slight decline beyond 40$^{\circ}C$. 2. Surface color of the silk changed from red to reddish purple and that of the wool showed red tone when mordanted with Aluminum postassium sulfate, Copper acetate and Copper (II) sulfate regardless of the mordanting conditions. 3. The light and dry cleaning fastness of silk and wool fabrics dyed with Lac extract according to the mordanting methods were very good.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1996년도 제10회 학술발표회 논문개요집
• /
• pp.144-144
• /
• 1996

• 청정기술
• /
• 제18권3호
• /
• pp.287-294
• /
• 2012

본 연구에서는 중고 레이저 복합기의 재제조 과정에서 복합기의 성능에 큰 영향을 미치는 인쇄회로기판(printed circuit board, PCB) 등 전자부품에 대하여 세정공정의 도입 적용 가능성을 분석하고 세정장치 및 최적의 운전조건을 설계하였다. 1단계로 물에 의한 부식의 염려가 없는 건식세정방식으로 플라즈마세정에 의한 세정성을 분석하였다. 플라즈마세정 의한 PCB세정에서는 세정이 어느 정도 이루어졌으나 플라즈마가 전도 될 수 있는 피세정물의 금속 부분 주위에서 피 세정물의 손상을 확인할 수 있었으며 레이저 복합기의 재제조용으로는 생산성 및 경제성이 부족하였다. 2단계에서는 경제성이 있는 초음파세정방식을 위하여 현재 현장에서 사용되고 있는 세정제를 포함하여 세정효율이 우수한 4종의 대체 세정제를 선정하여, 세정제의 물성을 측정하였고 세정성을 평가하였다. 준수계 세정제와 비수계 세정제보다 수계 세정제의 세정력이 우수 하였으며, 초음파 주파수가 작을수록 세정력이 우수하였다. 수계세정제 A를 사용하여 28 kHz의 초음파 세기에서 세정을 한다면 30초~1분 내에 빠른 세정이 가능할 것으로 판단되었다. 3단계에서는 선정된 세정제로 초음파 세정시스템을 구축하고, 실제 부품들을 초음파 세정하여 현장에서 사용이 적합한 최적의 세정조건을 구하였다. PCB 보드 및 대전기에 대하여 최적 세정 조건을 구한 결과, 40 kHz, $50^{\circ}C$에서 1분 30초 및 2분에 세정을 끝낼 수 있었다. 수작업에 의존하거나 외부처리를 하고 있는 중소 재제조 업체들은 본 세정시스템의 도입으로 전자부품 기능의 신뢰성이 확보되며 전체적인 재제조 공정의 생산성 및 경제성 향상에 큰 효과를 볼 수 있을 것으로 기대된다.