• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.1
• /
• pp.107-115
• /
• 2012

This study incorporates welders and generators needed to use it and welder generators to be used as is to configure the system. Thus in order to propose an integrated system to prevent the rapid charging process to manage the power state information, system configuration is the most important. Therefore, the battery charging output port, the main input and output control ports, the generator control port, a warning alarm buzzer, UI switch input, EXT power output, check the battery status input, battery charge and discharge current, UI input control switch, generator status, the main power input and output, the output voltage, EXT warning output, DEBUG communication, UI display unit, an external input ADC units with a focus on generator control system was implemented.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.82-88
• /
• 2008

This paper describes the influence of the bridge formed between electrodes by electrolyte for tracking process. Electrolytes is made by IEC(International Electrotechnical Commission) 60589, NaCl added to deionized water as each 1, 3, 5[wt%]. The used test equipment is made according to KS(Korean Industrial Standard) C IEC 00112. It is investigated voltage, current, value of resistance and thermal image when bridge formed between electrodes on tracking process. As a result, as conductivity of electrolyte gets bigger as Joule's heat on bridge also gets bigger. But It is not over electrolyte's boiling point due to evaporation heat of electrolyte. However as conductivity of electrolyte gets bigger as the necessary time of dry band gets shorter. So dry band is existed more long time between ahead of droplet to next droplet and discharge chance at dry band gets much. Therefore tracking process gets faster.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.1
• /
• pp.79-84
• /
• 2003

$WC-Ti_{1}$ -xA $l_{x}$ N multilayered coatings are performed by their periodically repeated structures of lamellae of WC-Ti/$WC-Ti_{1}$ -xA $l_{x}$ Nmaterials. The $WC-Ti_{1}$ -xA $l_{x}$ N coatings with variable Al content were deposited onto AISI D2 steel by cathodic arc deposition (CAD) method. The electrochemical behavior of multilayered $WC-Ti_{1}$ -xA $l_{x}$ N coatings with different phases (WC- Ti$0.6/Al_{0.4}$ N, $WC-Ti_{0.53}$$Al_{0.47}$N, $WC-Ti_{0.5}$ $Al_{0.5}$ N and $WC-Ti_{ 0.43}$$Al_{0.57}$ N) was investigated in deaerated 3.5% NaCl solution at room temperature. The corrosion behaviors for the multilayered coatings were investigated by electrochemical techniques (potentiodynamic polarization) and surface analyses (X-ray diffraction (XRD), scanning electron microscopy (SEM), and glow discharge optical emission spectroscopy (GDOES)). In the petentiodynamic polarization test, the corrosion current density of $WC-Ti_{0.5}$$Al_{0.5}$N was lower than others.

• The Korean Journal of Quaternary Research
• /
• v.25 no.1
• /
• pp.1-13
• /
• 2011

To reinterpret the meaning of fluvial terraces in the Quaternary researches, the concepts and geomorphic properties of fluvial terraces are reviewed. Fluvial terraces are the alluvial landform that was once river channel or floodplain by paleochannel flowed in elevated areas from the current river by active incision of rivers due to the climatic changes and/or uplifts. As fluvial terraces are the remnants of alluviums after incisions of rivers, the major factors influencing on the incisions are the falling of erosion base, increase of river discharge and distinct geomorphic phenomenon of river. While it is generally known that fluvial terraces deposits in the upper or middle reaches of large rivers were formed during glacial periods, the deposits may be formed at the various periods due to the diverse natural environments and geomorphic properties of specific rivers, because there have been numerous cases that the ages of fluvial terraces in the upper or middle reaches of large rivers in Korea and China can be correlated to the interglacial periods.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.3
• /
• pp.307-315
• /
• 2016

The properties of AlTiN films by a cathodic arc deposition process have been studied. Oblique angle deposition has been applied to deposit AlTiN films. AlTiN films have been deposited on stainless steel (SUS304) and cemented carbide (WC) at a substrate temperature of $500^{\circ}C$. AlTiN films were analyzed by scanning electron microscopy, glow-discharge light spectroscopy, micro-vickers hardness, and nanoindenter. When applying a current of 50 A to the cathodic arc source, it showed that the density of macroparticle of AlTiN films was 5 lower than other deposition conditions. With the increase of the bias voltage applied to the substrate up to -150 V, the density of macroparticle was decreased. The change of the $N_2$ flow rate during coating process made no influence on the film properties. For the multi-layered films, the film prepared at oblique angle of $60^{\circ}$ showed the highest hardness of 28 GPa and $H^3/E^2$ index of 0.18. AlTiN films have been shown a good oxidation resistance up to $800^{\circ}C$.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1704-1711
• /
• 2014

Sandy and dusty weather condition often occurs in the high altitude areas of China, which may greatly influence the corona generated radio interference (RI) characteristics of the bundle conductors of 750 kV AC power transmission lines. Corona generated RI of the conductors of the 750 kV AC power transmission lines used in practice is measured by EMI receiver with a coupling circuit and a coupling capacitor connected between the high voltage side and the earth side in fine and sandy and dusty condition. The measuring frequency is 0.5 MHz, and the quasi-peak detection is used. RI excitation function is calculated based on the corona RI current measured by the EMI receiver. Corona generated RI characteristics were analyzed from sand concentration and sand particle size. The test result shows that the corona generated RI excitation function is influenced by the sandy and dusty condition. Corona discharge of the conductors is more serious in sandy and dusty condition with an ultraviolet (UV) detector. Corona generated RI excitation function increases with the increase of sand concentration and also increases with the increase of particle size.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.275-275
• /
• 2007

Two sorts of electrode composed of Sulpur/CNT/PVDF and Silver/CNT/PVDF were prepared by in situ chemical method and their electrochemical performance were evaluated by using cyclic voltammetry, impedance measurement and constant-current charge/discharge cycling technique. Also, composite electrodes were characterized by FE-SEM and BET. Raw materials such as CNT/Silver and CNT/Sulfur were mixed in ethanol, dried. These mixed materials were heated at 900 and $320^{\circ}C$ for 2hr, respectively in order to enhance contact among CNT electrodes. Electric double layer capacitor cells were fabricated using these mixed powder with polymer of PVDF. For the charging and discharging characteristics measured at scan rate of 1 mA/s, Supercapacitor of Sulphur-CNT-PVDF electrode showed a better performance than that of Ag-CNT-PVDF, which seems to be related with lower contact resistance of Sulphur-CNT-PVDF electrode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.597-598
• /
• 2005

Recently, the performance of portable electric equipment can often improved by a Li-ion battery assisted by a supercapacitor. A supercapacitor can provide high power density as well as a low resistance in the hybrid system. In this study, we have prepared, as the pluse power souce, a commercially supplied Li-ion battery with a capacity of 700mAh and AC resistivity of $60m\Omega$ at 1kHz and nonaqeous asymmetric hybrid capacitor composed of an activated carbon cathode and MCMB anode, and have examined the electrochemical characteristics of hybrid capacitor and the pulse performances of parallel connected battery/hybrid capacitor source. The nonaqueous asymmetric hybrid capacitor, the stacks of 10 pairs of the cathode, the porous separator and the anode electrode were housed in Al-laminated film cell. The hybrid capacitor, which was charged and discharged at a constant current at $0.25mA/cm^2$ between 3 and 4.3V, has exhibited the capacitance of 100F. And the equivalent series resistance was $32m\Omega$ at 1kHz. By combining a Li-ion battery and a hybrid capacitor, the pulse performance of battery can be improved 23% in run time under a pulse discharge of 7C-rate.

• Nuclear Engineering and Technology
• /
• v.12 no.3
• /
• pp.163-170
• /
• 1980

A Mather type plasms gun is operated at below 1 torr with a energy storage system (4KJ, 16.5KV, 35nH) to study the conditions of the efficient plasma focus. When the $D_2$ gas filling pressure is 0.18 torr and the stored energy is 3.8KJ, the discharge current of max. 180KA is obtained and the average axial velocity of the plasma is about $7cm/\mu\textrm{s}$. This is lower than the calculated velocity with above conditions by the snow-plow model. The discrepancy is due to the currents flowing over the insulator surface. The plasma focus occurs at low pressure compared with the results obtained by Bruzzone. The reasons are such that the plasma gun employed in this experiment is large for tile stored energy and the concentration of the residual gas is comparatively high. It is confirmed by a Long counter that the neutrons are generated from the dense plasma focus.

• Korean Journal of Optics and Photonics
• /
• v.1 no.2
• /
• pp.155-161
• /
• 1990

A Continous wave tunable $CO_2$ laser which is the slow axial flow type was construccted for the optical pumping of methyl alcohol ($CH_3OH$) laser. The reflective grating of 100 grooveslmm and 10.6$\mu\textrm{m}$ blaze wavelength was used to select wavelength. We have investigated continous outpu: power characteristics, and then have compared tuned output power profile with the gain curve of $CO_2$ laser. The optimum condition for maxium power was found at the gas mixing ratio 1 : 3 : 10 for $CO_2: N_2$ and He. under this condition the flow rate, pressure of lasing gas and discharge current are 9.5 llmin. 14 torr, and 55 mA respectively. The maxium output power was 55 Wlm. Output power of single wavelength operation was measured on 60 individual rotation vibration transitions in the P and K branches of the 9.5$\mu\textrm{m}$ band and 10.4$\mu\textrm{m}$ band in $CO_2$. The output power profile obtained from each band is well consistent with the gain curve of $CO_2$ laser and maxium tuned output power was 20 watt.