• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.4
• /
• pp.216-220
• /
• 2018

The piezoelectric properties of $0.65Pb(Zr_{1-x}Ti_x)O_3-0.35Pb(Zn_{1/6}Ni_{1/6}Nb_{2/3})O_3$ ($PZT_x-PZNN$) ceramics with $0.530{\leq}x{\leq}0.555$ were investigated for application to piezoelectric energy harvesters. Although a morphotropic phase boundary (MPB) was found at approximately x = 0.545, the ceramic with the highest figure of merit (FOM) ($d_{33}{\times}g_{33}$) was observed at a composition of x = 0.540. Values of this figure of merit, $d_{33}{\times}g_{33}$, of $19.6pm^2/N$ and $20.2pm^2/N$ were obtained from $PZT_{0.540}-PZNN$ ceramics sintered at $920^{\circ}C$ and $950^{\circ}C$, respectively. A high output power of $937{\mu}W$ and a high power density of $3.3mW/cm^3$ were obtained from unimorph-type piezoelectric energy harvesters fabricated using $PZT_{0.540}-PZNN$ ceramic sintered at $920^{\circ}C$ for 4h.

• Journal of Mechanical Science and Technology
• /
• v.20 no.12
• /
• pp.2094-2104
• /
• 2006

As demands for complex microstructures with high aspect ratios have increased, the existing methods, MEMS and LIGA, have had difficulties coping with the number of masks and fabricable heights. A microstereolithography technology can meet these demands because it has no need of masks and is capable of fabricating high aspect ratio microstructures. In this technology, 3D part is fabricated by stacking layers, 2D sections, which are sliced from STL file, and the Dynamic Image Projection process enables the resin surface to be cured by a dynamic image generated with $DMD^{TM}$ (Digital Micromirror Device) and one irradiation. In this paper, we address optical design process for implementing this microstereolithography system that takes the light path based on DMD operation and image-formation on the resin surface using an optical design program into consideration. To verify the performance of this implemented microstereolithography system, complex 3D microstructures with high aspect ratios were fabricated.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.7
• /
• pp.1385-1390
• /
• 2011

A coaxial-conical-radial transmission line conversion circuits have been investigated to realize a low loss high performance microwave power divider/combiner. In order to optimize the characteristics of the device, the power divider/combiner was designed separately with two parts-the inner part and the outer part. Utilizing the rectangular approximation of the outer part, we can design the low loss device which is not affected by the partition number N of the outer part. The small return loss which is lower than 20dB was obtained on the frequency range of 5.15GHz(7.45~12.60GHz). A conical connector was employed for smooth connection between the central coaxial line and the outer radial line. Making use of the $47^{\circ}$ and $90^{\circ}$ 2-stage conical connector, the return loss lower than 30dB was obtained on the operating frequency range of 5GHz. The total return loss of the designed divider/combiner was lower than 20dB on the frequency range of 5GHz for the partition number N=11, N=12 and N=16.

• The Journal of Korea Robotics Society
• /
• v.17 no.2
• /
• pp.152-158
• /
• 2022

As various mobile robots and manipulator robots have been commercialized, robots that can be used by individuals in their daily life have begun to appear. With the development of robots that support daily life, the interaction between robots and humans is becoming more important. Manipulator robots that support daily life must perform tasks such as pressing buttons or picking up objects safely. In many cases, this requires expensive multi-axis force/torque sensors to measure the interaction. In this study, we introduce a low-cost two-axis pressure sensor that can be applied to manipulators for education or research. The proposed system used three force sensitive resistor (FSR) sensors and the structure was fabricated by 3D printing. An experimental device using a load cell was constructed to measure the biaxial pressure. The manufactured prototype was able to distinguish the +-x-axis and the +-y-axis pressures.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.220-226
• /
• 2000

High precision step motor using Terfenol-D linear actuators is proposed and its performance is tested. Four Terfenol-D linear actuators are set up perpendicular to the rotor and saw-tooth current signals are applied on the actuators. It was found that the rotation angle is increased as the excitation current, the inertia of the rotor, and the contact force between the rotor and the push device are increased. The rotation angle per step of $0.001^{\circ}$ and blocking torque of 0.2Nm are achieved. The effect of the time delay between the excitation signals is also investigated.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.12
• /
• pp.547-549
• /
• 2006

We have proposed a novel algorithm for detecting scan alluk on the surface of a TFT-LCD device that is generated by non-uniform exposure during fabrication. The scan alluk is known to have similar intensity values on paths that are determined by the shape of lens for light exposure. Based on the observation, the proposed algorithm inspects the uniformity on the paths using 1D projection image of 2D LCD image and 2D backprojection image of the 1D image. We have shown the usefullness of the proposed method by theoretical analysis and experimental results.

• Journal of computational fluids engineering
• /
• v.11 no.2 s.33
• /
• pp.56-61
• /
• 2006

As the size and dimension of target problems in the field of computational engineering including CFD gets bigger and higher, it is needed to have more efficient and flexible data visualization environment in terms of software and hardware. Even though it is still manageable to use a mouse in controlling 3-dimensional data visualization, it would be beneficial to use 3-D input device for 3-D visualization. 'Data Glove' is one of the best 3-D input devices, because human hands are best tools for understanding 3-D space and manipulating 3-D objects. Signals coming from 'Data Glove' are analog and very sensitive to finger motions, therefore signal filtering using a digital filter is applied. This paper describes our experience and benefits of using data gloves in controlling 3-dimensional postprocessing softwares.

• Journal of the Korean Ceramic Society
• /
• v.47 no.1
• /
• pp.92-96
• /
• 2010

Based on the differential electrode equilibria approach, potentiometric YSZ sensors with semiconducting oxide electrodes for CO detection are developed. To improve the selectivity, sensitivity and response-time of the sensor, our strategy includes (a) selection of an oxide with a semiconducting response to CO, (b) addition of other semiconducting materials, (c) addition of a catalyst (Pd), (d) utilization of combined p- and n-type electrodes in one sensor configuration, and (e) optimization of operating temperatures. Excellent sensing performance is obtained by a novel device structure incorporating $La_2CuO_4$ electrodes on one side and $TiO_2$-based electrodes on opposite substrate faces with Pt contacts. The resulting response produces additive effects for the individual $La_2CuO_4$ and $TiO_2$-based electrodes voltages, thereby realizing an even higher CO sensitivity. The device also is highly selective to CO versus NO with minor sensitivity for NO concentration, compared to a notably large CO sensitivity.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.1
• /
• pp.12-17
• /
• 2004

The body-tied FinFETs (bulk FinFETs) implemented on bulk Si substrate were characterized through 3-dimensional device simulation. By controlling the doping profile along the vertical fin body, the bulk FinFETs can be scaled down to sub-30 nm. Device characteristics with the body shape were also shown. At a contact resistivity of $1{\times}10^{-7}\;{\Omega}\;cm^2$, the device with side metal contact of fin source/drain showed higher drain current by about two. The C-V results were also shown for the first time.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.2
• /
• pp.98-104
• /
• 1990

A study of the operation of surface and buried mode PMOSFET's is condusted. Using device with different channel length and channel implant dosage, threshold voltage lowering, transcon-diuctance and subthreshold characteristics of surface mode PMOFET are compared with those of buried mode MPOSFET. From the results, the surface channel device were more resistant to short channel effect than the buried channel device.