• Journal of Power Electronics
• /
• 제2권4호
• /
• pp.288-296
• /
• 2002

In this paper, a high frequency transformer - assisted auxiliary active resonant commutated snubber (HFTA-ARCS) for voltage source soft switching pulse width modulated power conversion circuits is presented. A three phase voltage source type soft switching inverter incorporating HFTA-ARCS circuits in its three bridge legs can reduce current rating of auxiliary active power switches and has sensorless simplified control scheme which any specified boost current management is not required for soft switching. Its operation principle and digital control scheme are described and a practical design method of circuit parameters on this HFTA-ARCS circuit is also introduced on the basis of computer simulation. Moreover, this space voltage vector modulated soft switching inverter system with DSP-based digital control scheme Is discussed and its effectiveness is proved on the basis of performance evaluations. The operating performances of this inverter system are also compared with those of conventional three-phase hard switching inverter under practical conditions of specified parameters.

• Journal of Power Electronics
• /
• 제10권6호
• /
• pp.673-679
• /
• 2010

Input-series-output-parallel (ISOP) connected DC-DC converters enable low voltage rating switches to be used in high voltage input applications. In this paper, a DSP is adopted to generate digital phase-shifted PWM signals and to fulfill the closed-loop control function for ISOP connected two full-bridge DC-DC converters. Moreover, a stable output current sharing control strategy is proposed for the system, with which equal sharing of the input voltage and the load current can be achieved without any input voltage control loops. Based on small signal analysis with the state space average method, a loop gain design with the proposed scheme is made. Compared with the conventional IVS scheme, the proposed strategy leads to simplification of the output voltage regulator design and better static and dynamic responses. The effectiveness of the proposed control strategy is verified by the simulation and experimental results of an ISOP system made up of two full-bridge DC-DC converters.

• Smart Structures and Systems
• /
• 제19권1호
• /
• pp.47-56
• /
• 2017

Considerable achievements in developing structural regulators as an important method for vibration control have been made over the last few decades. The use of large quantities of cables in traditional wired control systems to connect sensors, controllers, and actuators makes the structural regulators complicated and expensive. A wireless decentralized control experimental platform based on Wi-Fi unit is designed and implemented in this study. Centralized and decentralized control strategies as sample controllers are employed in this control system. An optimal control algorithm based on Kalman estimator is embedded in the dSPACE controller and the DSP controller. To examine the performance of this control scheme, a three-story steel structure is developed with active mass dampers installed on each floor as the wireless communication platform. Experimental results show that the wireless decentralized control exhibits good control performance and has various potential applications in industrial control systems. The proposed experimental system may become a benchmark platform for the validation of the corresponding wireless control algorithm.

• KIEE International Transactions on Power Engineering
• /
• 제4A권3호
• /
• pp.129-133
• /
• 2004

This paper deals with the design and implementation of a TCSC (Thyristor Controlled Series Capacitor) simulator, which is a module for an analog type power system simulator. Principally, it presents configuration of controller hardware/software and its experimental results. An analog type power system simulator consists of numerous power system components, such as various types of generator models, scale-downed transmission line modules, transformer models, switches and FACTS (Flexible AC Transmission System) devices. It has been utilized for the verification of the control algorithm and the study of system characteristics analysis. This TCSC simulator is designed for 50% line compensation rate and considered for damping resister characteristic analysis. Its power rate is three phase 380V 20kVA. For hardware extendibility, its controller is designed with VMEBUS and its main CPU is TMS320C32 DSP (Digital Signal Processor). For real time control and communications, its controller is applied to the RTOS (Real Time Operation System) for multi-tasking. This RTOS is uC/OS-II. The experimental results of capacitive mode and inductive mode operations verify the fundamental operations of the TCSC.

• Journal of Power Electronics
• /
• 제17권3호
• /
• pp.610-620
• /
• 2017

The Finite Control Set-Model Predictive Controller (FCS-MPC) for quasi Z-Source Inverters (qZSIs) is designed to reduce the number of sensors by proposing a current observer for the inductor current. Unlike the traditional FCS-MPC algorithm, the proposed model removes the inductor current sensor and observes the inductor current value based on the deposited prior optimized state as well as the capacitor voltage during this state. The proposed observer has been validated versus a typical MPC. Then, a comparative study between the proposed Modified Finite Control Set-Model Predictive Controller (MFCS-MPC) and a linear PID controller is provided under the same operating conditions. This study demonstrates that the dynamic response of the control objectives by MFCS-MPC is faster than that of the PID. On the other hand, the PID controller has a lower Total Harmonic Distortion (THD) when compared to the MFCS-MPC at the same average switching. Experimental results validate both methods using a DSP F28335.

• 전자공학회논문지CI
• /
• 제46권4호
• /
• pp.94-101
• /
• 2009

본 논문은 냉각형 적외선(infrared focal plane array; IRFPA) 영상시스템에서 하드웨어 뉴럴 네트워크를 이용한 실시간 고정패턴잡음 제어를 위해 고속 DSP & FPGA 기반의 H/W 설계 방법을 제안한다. 고정패턴잡음은 검출기의 불균일 보정처리후에도 관측영상의 온도분포 변화에 의해 발생한다. 이것은 열상 화질의 저하뿐만 아니라 다른 응용에도 문제되는 중요한 요소이다. 냉각형 적외선 영상시스템의 신호처리구조는 저온, 상온, 고온의 3개 테이블을 기준으로 이득(gain) 값과 편차(offset) 값을 연산한다. 제안된 방법은 3개 편차 테이블에서 각각 교차되는 영역을 세분화하여 가상의 테이블을 만들고, 입력 영상의 구분된 3개 영역에서 영상의 평균값으로 하드웨어 뉴럴 네트워크의 가중치 값을 조정하여 최적의 온도구간을 선정한다. 이와 같은 방법은 영상의 평균값으로부터 저온, 상온, 혹은 고온의 이득, 편차 테이블을 연산하고, 운용 중에 지속적으로 편차 보상을 적용하지 않아도 된다. 따라서 제안된 방법은 실시간 처리로 관측영상의 온도분포 변화에 의해 발생하는 고정패턴잡음을 제어하여 영상화질의 개선된 결과를 보였다.

• 센서학회지
• /
• 제7권2호
• /
• pp.124-130
• /
• 1998

독립적인 로보트나 자동차 제어 응용을 위하여 고속 3-D 비젼시스템들은 매우 중요하다. 이 논문은 다음과 같은 세가지 과정으로 구성되는 stereo vision process 개발에 대하여 논술한다 : 왼쪽과 오른쪽 이미지의 edges 추출, matching coresponding edges와 3-D map의 계산. 이 process는 VME 150/40 Imaging Technology vision system에서 이루어졌다. 이것은 display, acqusition, 4Mbytes image frame memory와 세 개의 연산 카드로 구성되는 modular system이다. 40 MHz로 작동하는 프로그래머불 연산 모듈은 $64{\times}32$ bit instruction cache와 두개의 $1024{\times}32$ bit RAM을 가진 TMS320C31 DSP에 기초를 두고 있다. 그것들은 각각 512 Kbyte static RAM, 4 Mbyte image memory, 1 Mbyte flash EEPROM과 하나의 직렬 포트로 구성되어있다. 모듈간의 데이터 전송과 교환은 8 bit globalvideo bus와 세 개의 local configurable pipeline 8 bit video bus에 의하여 이루어졌고, system management를 위하여 VME bus가 쓰였다. 두 개의 DSP는 왼쪽 및 오른쪽 이미지 edges 검출을 위하여 쓰였고 마지막 processor는 matching process와 3-D 연산에 사용되었다. $512{\times}512$픽셀 이미지에서 이 센서는 scene complexity에 따라 1Hz정도의 조밀한 3-D map을 생성했다. 특수목적의 multiprocessor card들을 사용하면 결과를 향상시킬 수 있을 것이다.

• 전자공학회논문지SC
• /
• 제47권1호
• /
• pp.17-28
• /
• 2010

본 논문은 DSP를 이용한 새로운 형태의 TFT-LCD 자동 화질 최적화 시스템을 제안한다. 실제 산업 현장에서 이와 같은 화질 최적화 과정은 시행착오를 반복하는 형식으로 진행되어 많은 시간이 소요되고 있으며 LCD 개발 엔지니어들의 성향 및 숙련도에 따라 조정 결과에도 편차가 큰 문제점이 있다. 이러한 시스템은 평균 감마 오차, 감마 조정 시간 및 플리커 등을 줄이기 위해 모바일 LCD 구동 IC 내의 감마 조정 레지스터들과 전압 설정 레지스터들을 자동적으로 제어한다. 제안된 최적 화질 향상 시스템은 측정 대상이 되는 모듈 (MUT, LCD 모듈), 제어 프로그램, 휘도 측정용 멀티미디어 디스플레이 측정기 및 인터페이스용 제어 보드로 구성되어 있다. 개발된 시스템에는 참조 감마 곡선과의 6-점 프로그램 정합 기술을 이용한 새로운 알고리즘 및 자동 전압 설정 알고리즘이 내장되어 있다. 개발된 알고리즘과 프로그램은 범용 LCD 모듈에 적용가능하다. 또한 1.8, 2.0, 2.2 및 3.0 감마를 조정할 뿐만 아니라 플리커 수준을 자동으로 조절한다. 제어 보드는 DSP와 FPGA로 구성되어 있고, RGB 및 CPU와 같은 다양한 인터페이스들을 지원한다. 개발된 자동 감마 시스템은 기존의 시스템에 비해 현저히 짧은 감마 조정 시간 및 아주 작은 평균 감마 오차를 보였다. 또한 본 논문에서 제안하는 시스템은 최적화된 감마 곡선 설정을 이용한 개발 공정을 향상시키고, 고화질의 LCD를 제공하는데 아주 유용하다.

• 대한임베디드공학회논문지
• /
• 제7권6호
• /
• pp.339-343
• /
• 2012

Security and monitoring system has many applications and commonly used for detection, warning, alarm, etc. As the networking technology advances, user requirements are getting higher. An intelligent and cooperative surveillance system is proposed to meet current user demands and improve the performance. This paper focuses on the implementation issue for the embedded intelligent surveillance system. To cover wide area cooperative function is implemented and connected by wireless sensor network technology. Also to improve the performance lots of sensors are employed into the surveillance system to reduce the error but improve the detection probability. The proposed surveillance system is composed of vision sensor (camera), mic array sensor, PIR sensor, etc. Between the sensors, data is transferred by IEEE 802.11s or Zigbee protocol. We deployed a private network for the sensors and multiple gateways for better data throughput. The developed system is targeted to the traffic accident detection and alarm. However, its application can be easily changed to others by just changing software algorithm in a DSP chip.

• 한국소음진동공학회논문집
• /
• 제22권2호
• /
• pp.170-178
• /
• 2012

This paper is concerned with the development of power amplifier and controller for piezoelectric actuator and sensor used in smart structures. Even though a high-voltage power amplifier is provided in the form of an operational amplifier, a very high DC voltage is still necessary as a power supply. In this study, we propose a low-cost design for the power amplifier including the DC power supply. We also need a controller on which a control algorithm will be mounted. In general, a digital signal processing chip is popularly used because of high speed. However, only commercial product is available for smart structure applications. In this paper, a controller consisting of a DSP and electronic circuits suitable for piezoelectric sensor and actuator pair is proposed. To validate the proposed controller with power amplifier, experiment on smart structure was carried out. The experimental results show that the proposed control system can be effectively used for smart structure applications with low cost.