• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.4
• /
• pp.763-769
• /
• 2009

A series voltage compensation(SVC) system is a power-electronics controller that can protect sensitive loads from disturbance in the supply system. Especially, voltage sags are considered the dominant disturbances affecting the power quality. This paper dealt with a system of off-line type voltage sag compensation by using a bi-directional DC/DC converter of environmentally friendly ultra-capacitor. This capacitor is attached to the DC link of SVC through the high-efficiency DC/DC converter in order to compensate the DC link voltage drop during short-term power interruption as voltage sags. Therefore, in this paper, a DC/DC converter to control high-efficiency energy of ultra-capacitor and voltage sag detection algorithm of off-line type SVC systems are newly introduced. According to the results of experimental of prototype system, it is verified that the proposed system has effectiveness of voltage sag compensation using an ultra-capacitor.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.6
• /
• pp.564-571
• /
• 2001

This paper presents the VLSI design of highly efficient low voltage DC/DC converter for portable devices. All active devices are integrated on a single chip using a standard 0.65$\mu\textrm{m}$ CMOS process. The converter operates at the switching frequency of 1MHz for reducing the size of passive elements and uses a ZVS for minimizing the switching loss at high frequency. Simulation results show that the circuit can achieve a 95% efficiency when the output voltage is controlled to be 2V with the load of lW.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1727_1728
• /
• 2009

Nowadays DC-DC converter has been used widely in electronic production. It has a high requirement in wide input voltage, load variations, stability, providing a fast transient response and lower overshoot. However, it is not easy to be controlled because of its nonlinearity. In this paper, the nonlinear model of DC-DC converter is approximatedby four linear models and sub-controllers are designed by using the LMI guaranteeing the stability of the sub-systems at the same time. For the robust of the control system, an integral sliding mode control (ISMC) is applied together with LMI fuzzy controller. The proposed controller supports a fast and almost no overshooting transient response for the DC-DC converter control.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.650-654
• /
• 1999

In this paper, author describe the simulation results concerning the period doubling bifurcation route to chaos of DC/DC boost converter under current mode control to show that it is common phenomena on switching regulator when parameters are improperly chosen or continuously varied beyond the ensured region by system designer. Bifurcation diagrams of periodic orbits of inductor current and capacitor voltage of DC/DC boost converter are plotted with sampled data at moment of each clock pulse causing switching on. DC/DC boost converter studied on this paper is modelled by its state space equations as per switching condition under continuous conduction mode. Current reference signal and capacitance are chosen as the bifurcation parameters and those are varied in step for iterative calculation to find bifurcation points of periodic orbits of state variables.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.9
• /
• pp.1306-1314
• /
• 2015

This paper deals with a switching method of a three-phase interleaved bidirectional DC-DC converter to obtain high efficiency in wide load range. The proposed soft-switching method provides ZVS and ZCS at turn-on, and ZVS at turn-off of the switch as well as considerably reduced conduction loss in light load. Simulation and experiment are carried out with a bidirectional DC-DC converter having the power rating of 3 [kW], and those results show the validity of the proposed switching method.

• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.586-591
• /
• 2020

An interleaved current-fed high step-up DC-DC converter is proposed. Besides high voltage gain, a low ripple input current is achieved by adopting interleaving operation. Moreover, soft-switching characteristic of the proposed converter reduces switching losses of active power switches and raise the conversion efficiency. The reverse-recovery problem of output rectifiers is also alleviated by controlling the current changing rates of diodes by utilizing the leakage inductances of transformers. Experimental results obtained on a 200W prototype are discussed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.4
• /
• pp.61-72
• /
• 2007

This study proposed a high efficiency DC-DC converter with a new current doubler rectifier for fuel-cell systems for use with the Nexa(310-0027) PEMFC from the Ballard Co. The proposed high efficiency DC-DC converter for the fuel-cell system generated ZVS by applying partial resonance and using a phase shift PWM control method. Constantly switching frequency, loss of switching, peak current, and peak voltage were reduced by this system. In addition to this system, two inductors were attached to a rectifier circuit allowing it to be able to provide the direct current(DC) and DC voltage safely to a load with reduced ripple components. Also, by using the newly proposed current doubler rectifier, the high frequency DC-DC converter for the fuel cell system was capable of reaching a highest efficiency of 92[%] as compared to 88.3[%] efficiency in previous results, which means that efficiency increased 3.7[%]. The overall results were confirmed by a simulation and laboratory experiment.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.485-486
• /
• 2010

FPS(Filament Power Supply), one of the KSTAR NBI (Neutral Beam Injections) is implemented by full-bridge DC/DC converter. NBI heating device for KSTAR(1.5MW) is developed for heating an ion source of plasma in KSTAR tokmak. The full-bridge DC/DC converter is applied to FPS for isolation with input and output. And FPS is operated with PWM control method which is the most usual method. In this paper, NBI FPS of 4.8kW is simulated by using the PSIM 6.0. And the full-bridge DC/DC converter using IGBTs is fabricated to demonstrate it. The processor DSP 28335 is implemented for digital control.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.879-891
• /
• 2018

A bidirectional dc-dc converter is used in battery energy storage systems owing to the growing requirements of a charging and discharging mode of battery. The magnetic coupling of output or input inductors in parallel-connected multi modules of a bidirectional dc-dc converter is often utilized to reduce the peak-to-peak ripple size of the inductor current. This study proposes a novel design guideline to achieve minimal ripple size of the inductor current under bidirectional power flow. The newly proposed design guideline of optimized coupling factor is applicable to the buck and boost operation modes of a bidirectional dc-dc converter. Therefore, the coupling factor value of the coupled inductor does not have to be optimized separately for buck and boost operation modes. This new observation is explained using the theoretical model of coupled inductor and confirmed through simulation and experimental test.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1275-1277
• /
• 2004

In this paper, we propose a new diagnosis method of DC/DC converter aging. The method is based on the variations of parasitic resistor for the aging process. We apply an on-line diagnosis of DC/DC converter because the observation is not a device, but a system. This study proposes a method of DC/DC converter diagnosis by analyzing the variations of model on the variations of parasitic resistor.