• Journal of Powder Materials
• /
• v.21 no.1
• /
• pp.34-38
• /
• 2014

Cu-Ni alloys with unidirectionally aligned pores were prepared by freeze-drying process of CuO-NiO/camphene slurry. Camphene slurries with dispersion stability by the addition of oligomeric polyester were frozen at $-25^{\circ}C$, and pores in the frozen specimens were generated by sublimation of the camphene during drying in air. The green bodies were hydrogen-reduced at $300^{\circ}C$ and sintered at $850^{\circ}C$ for 1 h. X-ray diffraction analysis revealed that CuO-NiO composite powders were completely converted to Cu-Ni alloy without any reaction phases by hydrogen reduction. The sintered samples showed large and aligned parallel pores to the camphene growth direction, and small pores in the internal wall of large pores. The pore size and porosity decreased with increase in CuO-NiO content from 5 to 10 vol%. The change of pore characteristics was explained by the degree of powder rearrangement in slurry and the accumulation behavior of powders in the interdendritic spaces of solidified camphene.

• Journal of Powder Materials
• /
• v.19 no.4
• /
• pp.317-321
• /
• 2012

In this study, Cu-5Ni-10Sn(wt%) spinodal alloy was manufactured by gas atomization spray forming, and the microstructural features and mechanical properties of Cu-5Ni-10Sn alloy have been investigated during homogenization, cold working and age-hardening. The spray formed Cu-5Ni-10Sn alloy consisted of an equiaxed microstructure with a mixture of solid solution ${\alpha}$-(CuNiSn) grains and lamellar-structure grains. Homogenization at $800^{\circ}C$ and subsequent rapid quenching formed a uniform solid solution ${\alpha}$-(CuNiSn) phase. Direct aging at $350^{\circ}C$ from the homogenized Cu-5Ni-10Sn alloy promoted the precipitation of finely distributed ${\gamma}$' or ${\gamma}-(Cu,Ni)_3Sn$ phase throughout the matrix, resulting in a significant increase in microhardness and tensile strength. Cold working prior to aging was effective in strengthening Cu-5Ni-10Sn alloy, which gave rise to a maximum tensile strength of 1165 MPa. Subsequent aging treatment slightly reduced the tensile strength to 1000-1100 MPa due to annealing effects.

• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1074-1082
• /
• 1997

Microstructure and permeability as a function of sintering temperature and composition were studied on the Ni$\delta$Cu0.4-$\delta$Zn0.6Fe2O4 ($\delta$=0, 0.1, 0.2, 0.3, 0.4) which was prepared by Cu2+ substitution for Ni2+ in Ni.0.4Zn0.6Fe2O4, then followed by 8 wt% CuO and 1wt% Bi2O3 as sintering aids. It was found that NiCuZn ferrite in which Cu2+ is substituted for Ni2+ is more effective in reduction of sintering temperature than Ni.0.4Zn0.6Fe2O4, containing CuO as a sintering aid. The specimen $\delta$=0.2 sintered at 90$0^{\circ}C$ for 2hr exhibited the highest initial permeability value ($\mu$o=280 at 1Mhz), but the real permeability decreased at the frequency under 10 MHz. EPMA analysis showed that Ni$\delta$Cu0.4-$\delta$Zn0.6Fe2O4 ($\delta$=0.4), sintered at 95$0^{\circ}C$ for 2hrs consisted of three phase regions of Ni.0.3Cu0.1Zn0.6Fe2O4 region, Cu and Bi liquid existed at the 3-point boundary, although the stabilization energy of Ni2+ is higher than that of Cu2+ in B site.

• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.4
• /
• pp.253-261
• /
• 1994

Transformation behavior and superelastic behavior of Ti-Ni-Cu alloys with various Cu content has been investigated by means of electrical resistivity measurement, X-ray diffraction, tensile test and transmission electron microscopy. Two types of heat treatment are given to the specimens: i) Solutions treatment. ii) thermo-mechanical treatment. The transformation sequence in solution treated Ti-Ni-Cu Alloys substituted by Cu for Ni up to 5at.% occurs to $B2{\rightleftarrows}B19^{\prime}$ and it proceeds in two stages by addition of 10at.%Cu, i. e, $B2{\rightleftarrows}B19{\rightleftarrows}B19^{\prime}$. Also, it has been found that Ti-30Ni-20Cu alloy transformed in one stage : $B2{\rightleftarrows}B19$. The thermo-mechanically treated Ti-47Ni-3Cu alloy transformed in two stages: B2${\rightleftarrows}$rhomboheral phase${\rightleftarrows}B19^{\prime}$, while transformation sequence in Ti-45Ni-5Cu and Ti-40Ni-10Cu alloy transformed as same as solution treated specimens. The critical stress for inducing slip deformation in solution treated and thermo-mechanically treated Ti-40Ni-10Cu alloy is about 90MPa and 320Mpa respectively.

• Journal of the Korean Magnetics Society
• /
• v.5 no.6
• /
• pp.937-946
• /
• 1995

In this research, the processing control of NiCuZn Ferrite has been developed. The relationship between initial permeability and bulk density of NiCuZn Ferrite with processing factors was studied. NiCuZn Ferrite, which calcinated at $700^{\circ}C$ for 3 hours, was ball milled for about 60 hours to make a size of $0.5\mu\textrm{m}$ followed by granulation using spray dryer. The physical properties and the magnetic properties of NiCuZn Ferrite were investigated with the processing factor, such as (i) granule size and forming pressure, and (ii) sintering temperature. The green density of NiCuZn Ferrite was largely depended on the forming pressure rather than its granule size. The green density of NiCuZn Ferrite was increased from $2.484\;g/cm^{3}$ to $3.002\;g/cm^{3}$ with increase in forming pressure. The bulk density of NiCuZn Ferrite was increased from $3.470\;g/cm^{3}$ to $4.754\;g/cm^{3}$ linearly with increase in sintering temperature. The relationship between initial permeability and bulk density of NiCuZn Ferrite was expressed with the empirical equation,$\mu_{i}=a+b_{\rho}+c_{\rho}^2$ at forming pressure and sintering temperature.

• Journal of Korea Foundry Society
• /
• v.41 no.5
• /
• pp.411-418
• /
• 2021

In order to experimentally investigate the effect of Ni or Cu addition on microstructure and mechanical properties of high Si Solution Strengthened Ferritic Ductile cast Iron (SSF DI), a series of lab-scale sand casting experiment were conducted by changing initial concentration of Ni up to 3.0wt% or Cu up to 0.9wt% in the alloy. It was found that increase in Ni or Cu content in the alloy leads to increase in strength properties and hardness as well as decrease in ductility. The higher Ni or Cu content the SSF DI has, the higher fraction of pearlite was observed. At similar levels of Ni or Cu contents in the alloy, higher pearlite area fraction was observed in the Cu-containing SSF DI than that in the Ni-containing SSF DI. When the effect of the microstructure on the mechanical properties of Ni-containing SSF DI was considered, Ni-containing SSF DI was found to have excellent strength and hardness as well as good elongation when the pearlite fraction was controlled less than 10%. As the pearlite fraction in the Ni-containing SSF DI exceeds 10%, however, it shows drastic decrease in elongation. Meanwhile, gradual increase in strength and hardness, and decrease in elongation with respect to increase in pearlite fraction were observed in Cu-containing SSF DI. The different microstructure-mechanical property relationships between Ni-containing and Cu-containing SSF DI were due to the combined effect of the relatively weak pearlite stabilizing effect of Ni compared to that of Cu in high Si SSF DI, and matrix strengthening effect caused by the different amounts of those alloying elements required for similar pearlite fraction.

• Journal of the Korean Magnetics Society
• /
• v.6 no.5
• /
• pp.329-333
• /
• 1996

We have studied the magnetoresistance and the magnetic anisotropy of Cu/(NiFe/Ni/NiFe) metallic multi layers grown on Si(100), Si(111), $4^{\circ}\;tilt-cut\;Si(111)$ or glass substrate. When the multilayer was grown on $4^{\circ}\;tilt-cut\;Si(111)$ with $50\;{\AA}$ of Cu underlayer, an in-plane uniaxial anisotropy was observed. On the other substrates such as Si(100), Si(111) or glass with Cu underlayer, however, no appreciable anisotropy was shown. The multilayer grown with NiFe or Ni underlayer or without underlayer did not show any arnsotropy even on $4^{\circ}\;tilt-cut\;Si(111)$. When $10\;{\AA}$ of NiFe was deposited prior to the Cu underlayer, the anisotropy in Cu/(NiFe/Ni/NiFe) multilayer disappeared.

• Journal of Energy Engineering
• /
• v.5 no.1
• /
• pp.65-71
• /
• 1996

Decomposition reaction of methanol was conducted on Ni-Cu/SiO$_2$catalysts with several variables. Variables used in this study are S.V(Space Velocity), partial pressure of methanol, reaction temperature, and composition rate of Ni-Cu. The range of S.V is 10,000-30,000h$\^$-1/, the temperature range is 150-400$^{\circ}C$ and values of Cu/(Ni＋Cu) are 0, 0.25, 0.5, 0.75, and 1. Over Ni/SiO$_2$, and Ni-Cu/SiO$_2$, the conversion rate of decomposition reaction of methanol arrived at 100% with increasing of temperature. At this time the selectivity of CO on Ni/SiO$_2$, was suddenly decreased, but on Ni-Cu/SiO$_2$, it was still sustained highly. The main products of reaction were CO and H$_2$, and by-products were CO$_2$ and CH$_4$mainly.

• Korean Journal of Materials Research
• /
• v.9 no.4
• /
• pp.335-340
• /
• 1999

The hot cracking phenomena and phase behaviors during hot working process of Cu-Ni bearing hot rolled steels were investigated by a $90^{\circ}$bending tests, BSE image analysis and EDS analysis. For aNi-free 1.2% Cu bearing steel, the surface hot cracking occurred about $1100^{\circ}C$ due to a liquid state Cu-enriched phase formed continuously at the interface between oxide scale and matrix. The liquid Cu-enriched phase penetrated into austenite grain boundaries and caused surface cracking during the hot working. In case of 0.6% Ni containing 1.2% Cu-Ni bearing steel, solid state Cu-Ni-riched phase existed at the scale/matrix interface as a discontinuous type. But the higher addition of 1.2% Ni, solid state Ni-Cu-riched phase was formed dominantly in the oxide scale. It was found that the addition of Ni suppressed the surface cracking of 1.2% Cu bearing steel by eliminating the liquid state Cu-enriched phase.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.1
• /
• pp.1-7
• /
• 2010

Interfacial reaction characteristics of a Bi-10Cu-20Sb-0.3Ni Pb-free alloy on Cu pad was investigated by reflow soldering at $430^{\circ}C$. The thickness of interfacial reaction layers with respect to the soldering time was also measured. After the reflow soldering, it was observed that a $(Cu,Ni)_2Sb$, a $Cu_4Sb$ intermetallic layer, and a haze layer, which is consisted of Bi and $Cu_4Sb$ phases, were successively formed at the Bi-10Cu-20Sb-0.3Ni/Cu interface. The total thickness of the reaction layers was found to be linearly increased with increasing of the reflow soldering time up to 120 s. As the added Ni element did not participate in the formation of the thickest $Cu_4Sb$ interfacial layer, suppression of the interfacial growth was not observed.