• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.211-212
• /
• 2009

국내의 다이아몬드 마이크로 블레이드 산업의 경우 충분한 이론적 검증을 거치지 못하고 종전의 경험 및 외산품에 대한 분석을 토대로 제작된 제품에 간단한 물성만을 체크하여 업체에 공급한다 해도 과언이 아니다. 이러한 국내의 실정을 인지하여 본 연구에서는 Cu와 Sn을 주 결합재로 사용한 다이아몬드 마이크로 블레이드에 있어 고체윤활제인 흑연과 $MoS_2$의 첨가에 따른 마모 특성을 비교하였다. 마모시험의 분위기는 상온에서 건식 분위기로 진행 되었으며, 그 결과 흑연을 첨가할 경우 가장 높은 마찰감소를 보임을 확인할 수 있었다. 이번 연구는 상온 및 저 회전 속도에서의 사용을 목적으로 한 다이아몬드공구의 연구 자료로 활용될 것이다.

• Composites Research
• /
• v.25 no.5
• /
• pp.159-163
• /
• 2012

The coating of metal surface with carbon nanotubes(CNTs) has been studied for the heat transfer enhancement of the boiling and condensation of refrigerant. The multiwalled carbon nanotube/copper oxide(CuO) composite powder, which has been surface modified by dispersant and polyvinyl alcohol solution, was ultrasonically sprayed and sintered on a copper wafer. In this paper, experiments were performed to assess the characterization and comparison of the carbon nanotube before and after sinterning and the morphology changes of the CNT/CuO-coated surface by using different dispersants. The dispersants used are THF (Tetrahydrofuran), SDBS(Dodecylbenzenesulfonic acid sodium salt), SDS(Sodium dodecy sulfate). The samples were examined by scanning electron microscopy(SEM), thermogravimetric analysis(TGA), differential scanning calorimeter(DSC) and Raman spectroscopy.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.995-999
• /
• 2007

The lead zirconate titanate (PZT) powders were synthesized to make the piezoelectric ceramics in low temperature as low as $900^{\circ}C$. To investigate the influence of additives on sintering of PZT, two kinds of sintering aids were made as follows; $wB_2O_3-xBi_2O_3-zCuO$and LiBiO2-CuO. The sintering aid, $1{\sim}3$ wt.% $LiBiO_2-CuO$, was added into these PZT powders and the specimens were fired at temperature in the range of $800{\sim}1200^{\circ}C$. The highest density was shown in the specimen with 1 wt.% $LiBiO_2-CuO$ as additive at temperature of $900^{\circ}C$. The sintered specimen were analyzed by X-ray diffraction(XRD) and scanning electron microscopy (SEM) was utilized to observe the microstructure, especially the densified morphology of specimens. In the XRD pattern, the well-crystallized PZT phase could be obtained in consequence of firing at $900^{\circ}C$. The scanning electron microscopy(SEM) was utilized to observe the structure of specimens after firing at $900^{\circ}C$. The densified perovskite structure of $PbZrTiO_3$ could be obtained by sintering at temperature as low as $900^{\circ}C$. The high sinterability of PZT ceramics was attributed to the low formation temperature of the liquid phase of additives.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.12
• /
• pp.851-857
• /
• 2014

Treatability of heavy metals in marine sediments contaminated with mainly organic matter was investigated on the basis of washing technology using oxidizers and surfactants. Sediment samples were collected at N area which expected for remediation project of contaminated marine sediment. For additives, hydrogen peroxide ($H_2O_2$) and Tween-80 were used at oxidizer and nonionic surfactant, respectively. In experiments, sediments was mixed with sea water at the ratio of 1 : 3 than $H_2O_2$ (1 M, 3 M, 4 M, 5 M) and Tween-80 (0.05%) were added. Samples were gathered at following reaction time (10, 20, 30, 40, 50, 60, 70, 80 min and 24 h). Total Organic Carbon (TOC) was 55.2% at the conditions of 5 M $H_2O_2+0.05%$ Tween-80 24 h. Hence total heavy metals were Cu 29.5%, Zn 42.3%, Cd 73.0% and bioavailable heavy metals were Cu 60.0%, Zn 77.7%, Cd 90.2% at the conditions of 5 M $H_2O_2+0.05%$ Tween-80 10 min. The correlations for between bioavailable metals (Cu, Zn, Cd) and TOC were significant (Cu, Zn, Cd; $r^2=0.94$, 0.85, 0.69, respectively).

• Journal of the Korean Electrochemical Society
• /
• v.18 no.1
• /
• pp.7-16
• /
• 2015

Effects of chemical composition ($Cu^{2+}$, $K_4P_2O_7$ and additive concentrations) of baths on properties of Cu thin films electrodeposited from pyrophosphate copper bath were investigated. Current efficiency was increased to be near 100% with increasing $Cu^{2+}$ concentrations from 0.02 to 0.3M. Decrease of current efficiency was observed in the range of 1.5~1.8M $K_4P_2O_7$ concentration, but current efficiency of about 100% was measured in the ranges of both 0.9~1.3M and 2.1~2.4M. The change of additive concentration did not influenced current efficiency. Residual stress of electrodeposited Cu thin films was measured to be about 20 MPa below 0.15 M $Cu^{2+}$ concentration and increased with the increase of it to 0.25 M. Maximum residual stress of 120MPa was observed at 0.25M $Cu^{2+}$ concentration. On the other hand, residual stress decreased from 80 to near 0 MPa as $K_4P_2O_7$ concentration varied from 0.9 to 2.4M and but The change of additive concentration did not affected on residual stress. $Cu^{2+}$ and $K_4P_2O_7$ concentrations significantly affect on surface morphology of electrodeposited Cu thin films, but additive concentration slightly affected. From XRD analysis, the microstructures of electrodeposited Cu thin film was affected from the changes of $Cu^{2+}$ and $K_4P_2O_7$ concentrations, but not from that of additive concentration. Strong preferred orientation of (111) peak was observed with increasing $Cu^{2+}$ and $K_4P_2O_7$ concentrations.

• Korean Journal of Materials Research
• /
• v.5 no.4
• /
• pp.490-500
• /
• 1995

다이아몬드와는 달리 CBN은 철족 재료 연삭시 화학적 마모가 거의 없다. 이러한 장점으로 인해 CBN휠이 철강 재료 연삭에 널리 사용되고 잇는 것이다. 그러나 CBN 휠의 성능은 CBN을 붙잡고 있는 결합제에 크게 의존한다. 오늘날 널리 사용되는 결합제인 주석 청동 합금은 내마모성에 한계가 있다. 주석 청동 합금의 내마모성을 증대시키기 위해 Co를 첨가하였다. 이러한 기지합금에 젖음성을 향사시키기위해 Co코팅 CBN을 사용하였다. 기지합금에 20%co를 첨가한 것이 입계에서 연속적인 $\delta$상생성, 취성 증가에 따라 자생작용이 활발하였다. 가장 높은 연삭비를 나타낸 것은 Cu-15wt%Sn, cu-33wt%Sn, co를 40:40:20으로 제작한 휠이었다.

• Journal of Korea Foundry Society
• /
• v.41 no.6
• /
• pp.528-534
• /
• 2021

To confirm effects of natural and artificial aging of precipitate on thermal diffusivity and hardness, the studied Al-Mg-Si alloy were manufactured by gravity casting method with 0.6 wt% and 1.0 wt% additional Cu element. The samples were used for measuring thermal diffusivity and hardness. The addition of Cu, promoted by intermediates such as Q'' and θ'' phases, contributing to the improvement of hardness and high-temperature thermal diffusivity. The natural aging decreased the hardness of the Al-Mg-Si-Cu alloys with increasing time, but did not affect the thermal diffusivity.

• Journal of the Korean Magnetics Society
• /
• v.16 no.4
• /
• pp.201-205
• /
• 2006

The electromagnetic properties and microstructure of the basic composition of $(Ni_{0.2}Cu_{0.2}ZnO_{0.2})_{1.02}(Fe_{2}O_{3})_{0.98}$ were invested, changing the amount of the additives $Bi_2O_3$ and $ZrO_2$ and sintering temperature. The spinel structure of specimen was confirmed by the analysis of XRD patterns. Grain size and its density are increased by increasing the additive and the sintering temperature.However, the permeability increased with decreasing additive. It was also found that $Bi_2O_3$ had more effect on the increase of grain size and permeability rather than $ZrO_2$.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1997.10a
• /
• pp.29-29
• /
• 1997

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1994.10b
• /
• pp.12-13
• /
• 1994