• Transactions on Electrical and Electronic Materials
• /
• v.7 no.1
• /
• pp.30-35
• /
• 2006

We have studied the motion of charged micro-particles that are immersed in a nematic liquid crystal (LC) and controlled by in-plane field. The LC is an anisotropic liquid such that the viscosity of the LC depends on flow direction, phase of the LC, and temperature, which affects the motion of the charged particles under the influence of electric field. This study shows that the motion of charged particles mainly depends on the applied voltage and the LC phase, but does not show any significant influence from the initial alignment of LC, although one may expect directional difference in drag force due to interaction between LC and particle. The viscosity changes due to temperature variations in nematic phase also show no signification influence on particle velocity when compared to the effect from varying in-plane field strength.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.8
• /
• pp.724-728
• /
• 2005

Electro-optic characteristics of reflective hybrid aligned liquid crystal (LC) cell driven by fringe field using a nematic LC with positive dielectric anisotropy have been studied. Optimized optical configurations are achieved by using a single polarizer, half-wave film and a cell with quarter-wave retardation. The simulation results shows an optimum cell retardation of $0.30{\mu}m$. This value may allow a practical cell gap larger than $3{\mu}m$, which makes it easy to control in the manufacturing process. Furthermore, this LC cell with optimized cell parameters shows low wavelength dispersion and the contrast ratio greater than 5 over exists about $100{\circ}$ in vertical direction and $160{\circ}$ in horizontal direction. Also, when using the LC with positive dielectric anisotropy rather than negative dielectric anisotropy, the display shows low power consumption and fast response time.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.10
• /
• pp.914-922
• /
• 2003

The FFS (fringe-field switching) mode was known to exhibit both a wide viewing angle and high transmittance, especially when using a liquid crystal with negative dielectric anisotropy. We have studied cell gap-dependent electrode-optic characteristics of the FFS mode using the LC with negative dielectric anisotropy. In case of a small cell gap of 2 ${\mu}$m, the transmittance at the center of pixel and common electrodes is relatively low because effect of surface anchoring that holds the LC to the initial state is larger than that in a large cell gap of 4 .urn such that the LCs in those regions cannot rotate enough. However, in case of a large cell gap of 4 .urn, the effect of surface anchoring becomes relatively small so that the LCs at the center of pixel and common electrode can be twisted enough by applied voltage, giving rise to high transmittance. Therefore, we can conclude that the light efficiency is dependent on the cell gap.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.6
• /
• pp.501-509
• /
• 2003

We have designed transflective liquid crystal display(LCD) associated with in-plane switching of a LC director driven by fringe-field, unlike other LCD mode. Reflective area consists of a λ/2 compensation film and a LC cell with retardation value(dΔn) of λ/4 with their optic axes making an angle of 15$^{\circ}$ and 75$^{\circ}$ against polarizer, respectively. In the transmissive area, top and bottom polarizers are parallel each other, an LC has a dΔn of λ/2, and another λ/2 compensation film is inserted between the LC cell and bottom polarizer. With the configuration, both devices show dark state initially. When an incident light is 550nm, the device shows wide-viewing-angle characteristics such that in the reflective area the contrast ratio target than 5 exists up to 55$^{\circ}$ of polar angle in all directions and in transmissive area it exists about 100$^{\circ}$ in vortical direction and 110$^{\circ}$ in horizontal direction.

• Korean Journal of Optics and Photonics
• /
• v.10 no.4
• /
• pp.267-272
• /
• 1999

We attached a fiber tip on the branch of a quartz crystal oscillator in order to make a feedback control system for near field optical microscope. The electrical impedance of the quartz crystal oscillator depends on the distance between the surface of the sample and the tip caused by the surface damping. Using this method, we can directly monitor the distance between the sample and the tip without inserting extra beam which might give extra optical noise. We characterize the XY scanning resolution and the amplitude of the vibrating tip and the Z-dependent decay of the evanescent wave.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.11
• /
• pp.892-897
• /
• 2001

Variations of dielectric and piezoelectric properties and associated phase transformation of <001> -oriented rhombohedral 0.92Pb (Zn$\sub$1/3/Nb$\sub$2/3/)O$_3$-0.08PbTiO$_3$ single crystals were investigated. The longitudinal strain level was found to abruptly increase at 15 kV/cm, corresponding to that where an induced phase appears within a multidomain matrix. Drastic decreases in the dielectric constant, transverse coupling, and transverse piezoelectric coefficient associated with the E-field induced phase were the result of increased crystal anisotropy in PZN-PT crystals. By contrast, the thickness coupling increased from 53 % at 0 kV/cm to 64 % at 45 kV/cm, also associated with this phase transition under the E-field. The measured dielectric and piezflelectric properties found for the induced phase state were nearly identical to those of <001> poled tetragonal (1-x)PZN-xPT (x>0.1) crystals. Based on these results, it is evident that the symmetry of induced phase is tetragonal.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.75-82
• /
• 2004

We have studied the influence of rubbing directions on electro-optic characteristics of the fringe field driven hybrid aligned nematic liquid crystal (LC) cell by computer simulation. When a LC with positive dielectric anisotropy is used, the results show that the driving voltage and transmittance decreases as the rubbing direction with respect to horizontal electric field direction increases. The reason for decrease in light transmission is the increase of tilt angle on the center of common electrode. In this paper, we have studied how the rubbing angle effects on the transmittance of the cell by investigating a distribution of electric field and LC director.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.957-960
• /
• 2003

We have studied the influence of rubbing directions on electro-optic characteristics of the fringe field driven hybrid aligned nematic liquid crystal (LC) cell by computer simulation. When a LC with positive dielectric anisotropy is used, the results show that the driving voltage and transmittance decreases as the rubbing direction with respect to horizontal electric field direction increases. The reason for decrease in light transmission is the reduction of twist angle and increase of tilt angle on the center of common electrode. In this paper, we have studied how the rubbing angle effects on the transmittance of the cell by investigating a distribution of electric field and LC director.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.3
• /
• pp.1114-1122
• /
• 1996

Variation of temperature field in a Hele-Shaw convection cell was measured by using a HSI true color image processing system and TLC(Thermochromic Liquid Crystal) solution. The relationship between the hue value of TLC color image and real temperature was obtained and this calibration result was used to measure the true temperature. The temperature field in the Hele-Shaw convection cell shows periodic characteristics of 45 sec at Ra = 9.3 * 10$\^$6/. The temperature field measurement technique developed in this study was proved to be a useful and powerful tool for analyzing the unsteady thermal fluid flows.

• Journal of Magnetics
• /
• v.18 no.1
• /
• pp.9-13
• /
• 2013

Shielding effects in conductive and magnetic materials were investigated as a function of properties, thickness and diameter. In this work, evaluations on passive conductive and magnetic shield specimens were achieved through experimentation set-up using 50 Hz single and three phase induction field sources. Analysis on material microstructure properties and characteristics of shielding specimens were performed with the use of vibrating sample magnetometer (VSM) and field emission scanning electron microscopy (FESEM). An induction field at $136{\mu}T$ of single phase system and $50{\mu}T$ of three phase systems were observed to the shield specimens with the thickness ranged of 0.2 mm to 0.4 mm. It is observed that shield specimen efficiency becomes inversely proportionate to the increment of induction fields. The decrease was attributed to the surface structure texture which relates to the crystallization and non-crystallization geometrical effects.