• 소성∙가공
• /
• 제28권1호
• /
• pp.15-20
• /
• 2019

The superplastic forming/diffusion bonding process has been developed to fabricate a core frame structure with joint nodes out of tubes, for the development of a titanium high performance bicycle. The hydroforming process has been applied for bulging of a tube in the superplastic condition before, and during the diffusion bonding process. In this experiment, a commercial Ti-3Al-2.5V tube was selected as raw material for the study. The forming experiment has been performed using a servo-hydraulic press with a capacity of 200 ton. Next, nitrogen gas was used to acquire necessary pressure for the bulging and bonding of the tubes to fabricate the joint nodes. The pertinent processing temperature was $870^{\circ}C$ for the superplastic hydroforming/diffusion bonding (SHF/DB) process, using the Ti-3Al-2.5V tube. The bonding quality and the progress of bulging and diffusion bonding have been observed by the investigation of the joining interfaces at the cross section of the joint structure. The control of the nitrogen pressure throughout the SHF/DB process, was an important factor to avoid any significant defects in the joint structure. The whole progress stage of the diffusion bonding could be observed at a joint interface. A core structure with 5 joint nodes to manufacture a titanium bicycle could be obtained in a SHF/DB process.

• Journal of the Korean Wood Science and Technology
• /
• 제44권4호
• /
• pp.607-615
• /
• 2016

The delamination along the annual ring on the cross-section of laminae and the bonding strength according to the tangential angle between laminae were evaluated for the production of 3-ply cross-laminated timber (CLT) using domestic larch. Since there is no standard for CLT in Korea, the production and test of specimens for bonding strength followed the standard procedure of "Structural glued laminated timber" (KS F 3021). The standard specifies to exclude any measurement from the cracks of timbers resulted from drying or knots during delamination test of the glued laminated timbers. However, the failure of cross-sectional tissues along the annual rings was observed near the glue-line of all specimens during the delamination test. Because this phenomenon can generate defects in the CLT that may be exposed to various temperatures and relative humidities after the actual construction, the delamination percentage was measured by including this wood failure. As a result, the delamination percentage of the CLT which had been combined in such a way that the annual rings of outer lamina were directed inward was the lowest, which was around 13%, regardless of the annual ring direction of the middle lamina. On the other hand, the delamination percentage of the CLT which had been combined in such a way that the annual rings of outer lamina were directed outward was the highest, which was around 26%. Furthermore, end-split occurred in the outer lamina during the drying process of the boiling delamination test, which affected the delamination percentage. Therefore, the soaking delamination test was found to be more appropriate for evaluating the delamination strength of CLT. The block shear strength of larch CLT was $3.9{\pm}0.9$ MPa on average, which was 46% lower than the block shear strength requirement (7.1 MPa) of the standard, but satisfied the criteria of the block shear strength (3.5 MPa) of the European Standard (prEN 16351: 2013).

• 멤브레인
• /
• 제10권3호
• /
• pp.148-154
• /
• 2000

본 연구에서는 sulfur-succinic acid의 가교제를 이용한 가교된 폴리비닐알코올(poly(vinyl alcohol), PVA) 가교막을 이용하여 MTBE-methanol 혼합액에 대하여 조업온도, 가교제의 조성에 따른 증기투과 공정의 투과 특성을 조사 하였다. 팽윤 실험을 통해 PVA/SSA 가교막에 대하여 가교제 조성에 따른 막의 구조와 PVA의 하이드록실기(-OH), SSA의 설폰기(-$SO_3$H)와 용매와의 수소결합의 두 가지 인자가 상호 보완적으로 작용하고 있음을 알 수 있었다. 투과 특성에 있어 SSA의 설폰기가 중요한 인자로 작용하였다. 예를 들면 7% SSA 막에 대해서는 수소결합의 효과보다는 가교도의 효과가 투과 특성에 중요한 요인으로 작용하며 5% SSA에 대해서는 수소결합의 효과가 중요하게 작용하였다. 증기투과 공정에 있어 막과 직접 접촉하는 증기상이 액상에 비하여 methanol의 농도가 낮아 PVA의 하이드록실기와 methanol과의 수소결합 확률이 감소함에 따라 투과 특성에 영향을 미친다. 결과적으로 7% SSA 막에 대하여 MTBE/mthanol=80/20 혼합액에 대하여 공급액의 온도 3$0^{\circ}C$에서 선택도 2187, 투과도 4.84g/$m^2$hr를 보여 주었다.

• 천문학회보
• /
• 제36권2호
• /
• pp.125.2-125.2
• /
• 2011

We are developing medium resolution cross-dispersed silicon grisms in the near IR region ($1.45{\sim}5.2{\mu}m$). The grisms will be installed in MIMIR, a multifunction instrument at the Lowel Observatory, USA. The two devices are designed to cover H and K band and L and M band simultaneously. Our goal is to make grism with R=3000 at 1.2 arcsec slit. The Silicon has high refractive index (n=3.4 at $1.5{\mu}m$) which enhances the resolving power by up to 5 times when compared to conventional material such as BK-7 (n=1.5 at 1.5 ${\mu}m$). The bonded grisms will be installed in a filter wheel for the uses switch from spectroscopic mode to imaging mode easily. Our device is compact and light weighted while it provides a decent resolving power. We produce monolithic grisms using e-beam lithography at the NASA JPL and chemically etching the grooves on the silicon prisms. Moreover, the main-disperser and cross-disperser will be contacted together by direct Si-Si bonding technique and eventually turn into one piece. The bonded pair offers more stability in terms of the layout of the spectrum and removes the Fresnel loss at the intersection of two grisms. We report on the proper wafer bonding steps through this research, and inspected the bonding quality thermally, optically and mechanically.

• Journal of the Korean Wood Science and Technology
• /
• 제52권1호
• /
• pp.58-69
• /
• 2024

To evaluate the adhesive characteristics of mixed cross-laminated timber (CLT) using domestic softwoods structural lumber proposed by KS F 3020 and yellow poplar, penetration depth of adhesive and thickness of bonding line were analyzed based on the results of boiling water soaking delamination. 3 Types of adhesives and 2 types of major layer were divided into a 5 ply CLT using yellow popular as minor layer. The bonding performance of the mixed CLT as structural members was evaluated based on the KS F 2081. The thickness of bonding line between layers of the mixed CLT was measured with a scanning electron microscope, and the adhesive penetration depth in the layer members was measured with an optical microscope. As a result of boiling water soaking delamination test of mixed CLT, the CLT specimens using PRF and PUR adhesives met the requirements of KS F 2081. It was verified that the penetration path of the adhesive in the layes was mainly through the tracheid cell in the case of Japanese larch and Korean red pine layers, and through the vessel and radial tissue in yellow popular layers. The penetration depth of the adhesive was the highest for the PRF adhesive under the same pressing time conditions, and the thickness of the bonding line was in inverse proportion to the penetration depth in the case of the PUR adhesive.

• Journal of the Korean Wood Science and Technology
• /
• 제47권5호
• /
• pp.655-662
• /
• 2019

This study evaluated the multi-bonding performances of timbers as well as those of reinforcement and timber to obtain data for preparing guidelines regarding the use of timbers as large structural members. For the multi-bonding performances of timbers, four types of bonding surfaces were prepared according to the pith position. For the bonding performances of FRP (fiber-reinforced plastic)/steel plate and timber, a total of 11 types of specimens were produced for the selection of the appropriate adhesive. The bonding performances of the produced specimens were evaluated through a water soaking delamination test, a water boiling delamination test, and a block shear strength test. The test results showed that the bonding strength of the bonding surface according to the pith position was highest in the specimen for which the two sections with the pith at the center of the cross-section on timber and between the bonding surfaces (the tangential and radial sections were mixed) were bonded. Furthermore, the specimens for which the section (radial section) with the pith on the bonding surface of the timber was bonded showed a high delamination percentage. The results of the block shear strength test showed that the bonding section did not have a significant effect on the shear strength, and that the measured wood failure percentage was higher than the KS standard value. The PVAc adhesive showed the highest bonding strength between larix timber and GFRP (glass FRP). Furthermore, the epoxy and polyurethane adhesives showed good bonding strength for CFRP (carbon FRP) and structure steel, respectively.

• 한국표면공학회지
• /
• 제54권5호
• /
• pp.207-212
• /
• 2021

The mechanical and electrical characteristics can be improved in 3D stacked IC technology which can accomplish the ultra-high integration by stacking more semiconductor chips within the limited package area through the Cu direct bonding method minimizing the performance degradation to the bonding surface to the inorganic compound or the oxide film etc. The surface was treated in a ultrasonic washer using a diamond abrasive to remove other component substances from the prepared cast plate substrate surface. FE-SEM was used to analyze the bonding characteristics of the bonded copper substrates, and the cross section of the bonded Cu conjugates at the sintering junction temperature of 100 ℃, 150 ℃, 200 ℃, 350 ℃ and the pressure of 2303 N/cm² and 3087 N/cm². At 2303 N/cm², the good bonding of copper substrate was confirmed at 350 ℃, and at the increased pressure of 3087 N/cm², the bonding condition of Cu was confirmed at low temperature junction temperature of 200 ℃. However, the recrystallization of Cu particles was observed due to increased pressure of 3087 N/cm² and diffusion of Cu atoms at high temperature of 350 ℃, which can lead to degradation in semiconductor manufacturing.

• 멤브레인
• /
• 제19권4호
• /
• pp.310-316
• /
• 2009

조직 공학용 지지체로 사용할 목적으로 제조된 가교된 lactide/hyaluronic acid (LA/HA) 막의 분해 특성을 살펴보았다. 가교제 1,3-butadiene diepoxide (BD), 1-ethyl-3-(3-dimethyl aminopropyl) carbodiimide (EDC)를 사용하여 얻어진 고분자 막을 $37^{\circ}C$로 조절된 항온조에서 증류수에 침전시켜 분해시켰다. 가교반응시 LA/HA 몰비가 작을수록, 가교제의 농도가 작을수록 생성된 고분자 막의 분해속도가 증가하였다. 분해될 때 막의 구조 변화를 살펴보기 위해 분해 전, 3일, 6일, 9일 후의 시료를 채취하여 핵자기 공명 분광법으로 분자 구조를 살펴보았다. EDC로 가교시킨 막의 경우 시간이 지남에 따라 HA-EDC 결합구조는 서서히 분해되는데 HA-LA 결합구조는 급격히 분해되어 6일 후에는 완전히 소멸되었다. BD로 가교시킨 막의 경우 가교된 결합 구조 모두 서서히 분해되었으며 3일, 6일이 지나면서 HA-BD 결합 구조는 원래의 89, 83%가 유지되었으나 HA-LA 결합 구조는 원래의 83, 65%로 유지되었다. 분해된 막을 전자 현미경으로 측정한 결과 분해 전후 표면에서 기공의 밀도는 크게 차이나지 않았으며, 표면과 측면의 구조도 크게 차이가 나지 않아 조직공학용 재료로써 사용할 때 아무런 문제가 없는 것으로 관찰되었다.

• 대한전자공학회논문지SD
• /
• 제42권6호
• /
• pp.17-22
• /
• 2005

유무기 하이브리드 SiOC 박막은 차세대 유력한 저유전상수를 갖는 박막이다. SiOC 박막의 결합구조는 FTIR 분석기를 이용하여 화학적 이동이 일어나는 것을 확인하여 분석하였다. 유기화학분야에서의 일반적인 화학적 이동은 red shift에 해당하지만, 하이브리드 타입의 SiOC 박막은 red shift 뿐만 아니라 특이한 경우에 해당하는 blue shift도 관찰되었다. 화학적 이동의 원인은 전기음성도가 큰 원소가 주변에 존재하는 수소결합사이의 상호작용 때문인데, SiOC 박막에서 blue shift는 전자를 많이 포함하는 메틸그룹이 증가함으로 생기는 기공을 만드는 원인을 제공한다. SiOC 박막의 결합구조 역시 2가지 유형의 화학적 이동에 따라서 cross-link 구조와 case-link 구조의 두 가지 유형으로 나타난다. 유량비와 증착할 때 주어지는 열에너지에 따라서 두 가지 결합구조를 나타낸다. cross-link 구조와 cross-link breakage 구조는 박막의 유전상수가 낮아지는 원인 서로 다르며 화학적 물리적인 특성 또한 다르게 나타나는 것을 증명하고 있다. Si-O-C cross-link 구조는 red shift의 원인이 된 수소결합에 의한 원자사이의 길이가 길어지는 효과에 의해 표면접착력이 개선되며, 유전상수 역시 감소하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제41권2호
• /
• pp.158-163
• /
• 2013

Cross laminated timber (CLT) has been an rising issue as a promising building material replacing steel-concrete in mid story rise construction. But, there was no specific standard for CLT because it had been developed in industrial section. Recently, new draft for requirements of CLT was proposed by EN which suggested to evaluate the performance of adhesive in CLT by the same method as glulam. But, it has been reported that shear performance of cross laminated timber is governed by rolling shear. Therefore, block shear tests were carried out to compare parallel to grain laminating and cross laminating using commercial one component PUR (Poly urethane resin). The result showed that the current glulam standard for evaluating bonding performance is not appropriate for CLT. Beacause shear strength of cross laminating decreased to 1/3 of parallel to grain laminating and this strength was representing shear performance of wood itself not the bond. However, cross laminating showed no significant effect on wood failure. Thus, wood failure can be used as a requirement of CLT bonding. Based on the results, cross laminating effect should be included when evaluating adhesive performance of CLT correctly and should be considered as an important factor.