• Journal of the Korean Electrochemical Society
• /
• v.23 no.4
• /
• pp.105-112
• /
• 2020

Transition metal oxide, which undergoes a conversion reaction in the negative electrode material for a lithium-ion batteries, has a high specific capacity, but still has several critical problems. In this study, manganese pyrophosphate (Mn₂P₂O₇), nickel pyrophosphate (Ni₂P₂O₇), and carbon composite materials with pyrophosphates as novel negative electrode materials instead of transition metal oxide, are synthesized through simple solid-state reaction. The initial reversible capacity of Mn₂P₂O₇ and Ni₂P₂O₇ are 333 and 340 mAh g^-1, and when the composite materials are composed with carbon, the reversible capacity increases to 433 and 387 mAh g^-1, respectively. The initial Coulombic efficiency is also improved by about 10%. The Mn₂P₂O₇ and carbon composite material has the highest initial capacity and efficiency, and has the best cycle performance. Mn₂P₂O₇ containing polyanion, has a lower specific capacity due to the large mass of polyanion compared to MnO (manganese oxide). However, since Mn₂P₂O₇ shows a voltage curve with a slope, the charging (lithiation) voltage increases from 0.51 to 0.57 V (vs. Li/Li⁺), and the discharge (delithiation) voltage decreases from 1.15 to 1.01 V (vs. Li/Li⁺). Therefore, the voltage efficiency of the cell is improved because the voltage difference between charging and discharging is greatly reduced from 0.64 to 0.44 V, and the operating voltage of the full cell increases because the negative electrode potential is lowered during the discharging process.

• Clean Technology
• /
• v.29 no.4
• /
• pp.255-261
• /
• 2023

Power semiconductors are semiconductors used for power conversion, transformation, distribution, and control. Recently, the global demand for high-voltage power semiconductors is increasing across various industrial fields, and optimization research on high-voltage IGBT components is urgently needed in these industries. For high-voltage IGBT development, setting the resistance value of the wafer and optimizing key unit processes are major variables in the electrical characteristics of the finished chip. Furthermore, the securing process and optimization of the technology to support high breakdown voltage is also important. Etching is a process of transferring the pattern of the mask circuit in the photolithography process to the wafer and removing unnecessary parts at the bottom of the photoresist film. Ion implantation is a process of injecting impurities along with thermal diffusion technology into the wafer substrate during the semiconductor manufacturing process. This process helps achieve a certain conductivity. In this study, dry etching and wet etching were controlled during field ring etching, which is an important process for forming a ring structure that supports the 3.3 kV breakdown voltage of IGBT, in order to analyze four conditions and form a stable body junction depth to secure the breakdown voltage. The field ring ion implantation process was optimized based on the TEG design by dividing it into four conditions. The wet etching 1-step method was advantageous in terms of process and work efficiency, and the ring pattern ion implantation conditions showed a doping concentration of 9.0E13 and an energy of 120 keV. The p-ion implantation conditions were optimized at a doping concentration of 6.5E13 and an energy of 80 keV, and the p+ ion implantation conditions were optimized at a doping concentration of 3.0E15 and an energy of 160 keV.

• Korean Chemical Engineering Research
• /
• v.52 no.5
• /
• pp.657-666
• /
• 2014

Coal gasification technology is considered as next generation clean coal technology even though it uses coal as fuel which releases huge amount of greenhouse gas because it has many advantages for carbon capture. Coal or pet-coke slurry gasification is very attractive technology at present and in the future because of its low construction cost and flexibility of slurry feeding system in spite of lower efficiency compared to dry feeding technology. In this study, we carried out gasification experiment using bituminous coal slurry sample by integrating coal slurry feeding facility and slurry burner into existing dry feeding compact gasifier. Especially, our experiment was conducted under fairly lower operation temperature than that of existing entrained-bed gasifier, resulting in partial slagging operation mode in which only part of ash was converted to slag and the rest of ash was released as fly ash. Carbon conversion rate was calculated from data analysis of collected slag and ash, and then cold gas efficiency, which is the most important indicator of gasifier performance, was estimated by carbon mass balance method. Fairly high performance considering pilot-scale experiment, 98.5% of carbon conversion and 60.4% of cold gas efficiency, was achieved. In addition, soundness of experimental result was verified from the comparison with chemical equilibrium composition and energy balance calculations.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.5
• /
• pp.211-216
• /
• 2018

The recovery of rare earth elements (REE) including La, Nd and Ce from spent batteries is important issues to reuse scarce resources. Herein, we present a simple recovery process to obtain lanthanum oxide ($La_2O_3$) from spent Ni-MH batteries, and demonstrate the conversion mechanism from $NaLa(SO_4)_2{\cdot}H_2O$ to $La_2O_3$. This strategy requires the initial preparation of $NaLa(SO_4)_2{\cdot}H_2O$ and subsequent metathesis reaction with $Na_2CO_3$ at $70^{\circ}C$. This metathesis reaction resulted in the crystalline lanthanum carbonate hydrate ($La_2(CO_3)_3{\cdot}xH_2O$) powder with plate-like morphology. On the basis of TGA result, the $La_2(CO_3)_3{\cdot}xH_2O$ powder was calcined in air at three different temperatures, that is, $300^{\circ}C$, $500^{\circ}C$, and $1000^{\circ}C$. As the calcination temperature increased, the morphology of powder was changed; prism-like ($NaLa(SO_4)_2{\cdot}H_2O$) ${\rightarrow}$ platelike ($La_2(CO_3)_3{\cdot}xH_2O$) ${\rightarrow}$ aggregated irregular shape ($La_2O_3$). Futhermore, XRD results indicated that the crystalline $La_2O_3$ could be synthesized after the metathesis reaction with $Na_2CO_3$, followed by heat-treatment at $1000^{\circ}C$, along with a change of crystallographic structures; $NaLa(SO_4)_2{\cdot}H_2O$ ${\rightarrow}$ $La_2(CO_3)_3{\cdot}xH_2O$ ${\rightarrow}$ $La_2O_3$.

• Microbiology and Biotechnology Letters
• /
• v.37 no.2
• /
• pp.118-124
• /
• 2009

Esterase EM2L8 gene isolated from deep sea sediment was expressed in Escherichia coli BL21 (DE3) and the esterase activity of the cell-free extract was assayed using p-nitrophenyl butyrate-spectrophotometric method. Its optimum temperature was $40-45^{\circ}C$ and 45% activity of the maximum activity was retained at $15^{\circ}C$. The activation energy at $15-45^{\circ}C$ was calculated to be 4.9 kcal/mol showing that esterase EM2L8 was a typical cold-adapted enzyme. Enzyme activity was maintained for 6 h and 4 weeks at $30^{\circ}C$ and $4^{\circ}C$, respectively. When each ethanol, methanol, and acetone was added to the reaction mixture to 15% concentration, enzyme activity was maintained. In the case of DMSO, enzyme activity was kept up to 40% concentration. (S)-4-Chloro-3-hydroxy butyric acid is a chiral intermediate for the synthesis of Atorvastatin, a hyperlipemia drug. When esterase EM2L8 (40 U) was added to buffer solution (1.2 mL, pH 9.0) containing ethyl-(R,S)-4-chloro-3-hydroxybutyrate (38 mM), it was hydrolyzed into 4-chloro-3-hydroxy butyric acid with a rate of $6.8\;{\mu}mole/h$. The enzyme hydrolyzed (S)-substrate more rapidly than (R)-substrate. When conversion yield was 80%, e.e.s value was 40%. When DMSO was added, hydrolysis rate increased to $10.4\;{\mu}mole/h$. The plots of conversion yield vs e.e.s in the presence or absence of DMSO were almost same, implying that the reaction enantioselectivity was not changed by the addition of DMSO. Taken together, esterase EM2L8 had high activity and stability at low temperatures as well as in various organic solvents/aqueous solutions. These properties suggested that it could be used as a biocatalyst in the synthesis of useful pharmaceuticals.

• Asian-Australasian Journal of Animal Sciences
• /
• v.28 no.3
• /
• pp.382-390
• /
• 2015

This work was conducted to investigate the performance and meat characteristics of commercial Korean native duck (KND). A total of 180 1-d-old ducklings of 2-way crossbreds from A and B lines (from National Institute of Animal Science) were used in this work and divided into 4 groups (3 replicates/group, 15 birds/replicate). The four groups were 4 crossbreds as AA (A line [♀]${\times}$A line [♂]), AB (A line [♀]${\times}$B line [♂]), BB (Pure line B strains) and BA (B strains [♀]${\times}$A strain [♂]). Ducks were fed diets based on corn-soybean meal for 0 to 3 wk (22.4% crude protein [CP], 2,945 kcal/kg metabolizable energy [ME]) and 3 to 8 wk (18.4% CP, 3,047 kcal/kg ME). As a result of this study, average body weight of 4 crossbreds were 625, 1,617, 2,466, and 2,836 g at 2, 4, 6, and 8 weeks, respectively, and significantly increased over the period of time (p<0.05). Body weight of BB group was greater than other crossbreds at the age of 6 weeks (p<0.05). There was a significant difference in weekly body weight gains (p<0.05), which were 573, 991, 850, and 371 g at 2, 4, 6, and 8 weeks old, respectively. Uniformity of 4 crossbreds was 84.9%, 80.5%, and 72.5% at 6, 7, and 8 weeks, respectively, and there was no difference among crossbreds. Body weight gain of BB crossbred was highest among crossbreds (p<0.05). Weekly feed intake significantly increased with weeks as 669, 1,839, 2,812, and 3,381 g at 2, 4, 6, and 8 weeks respectively (p<0.05). Feed intakes of AA and BB crossbreds were higher at 2 to 4 weeks old than others and that of BB crossbred was highest at 4 to 6 weeks old (p<0.05). Weekly feed conversion ratios were 1.17, 1.86, 3.32, and 9.37 at 0 to 2, 2 to 4, 4 to 6, and 6 to 8 weeks old, respectively, and it increased with age (p<0.05). There was no significant difference in feed conversion ratio among crossbreds. Carcass yields of 4 crossbreds were 73.6%, 71.6%, 73.5%, and 71.7%, respectively, so there was no significant difference among crossbreds. There was no difference in wing, neck, breast and leg ratios among crossbreds. However, back ratios of 4 crossbreds were 17.6%, 18.0%, 15.8%, and 17.6%, respectively, and back ratio of BB was the highest among crossbreds. Finally, these results may provide the basic data on the production, carcass quality, fatty acid and amino acid composition of commercial KND with 2-way crossbreeding.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.375-375
• /
• 2010

CdTe as an absorber material is widely used in thin film solar cells with the heterostructure due to its almost ideal band gap energy of 1.45 eV, high photovoltaic conversion efficiency, low cost and stable performance. The deposition methods and preparation conditions for the fabrication of CdTe are very important for the achievement of high solar cell conversion efficiency. There are some rearranged reports about the deposition methods available for the preparation of CdTe thin films such as close spaced sublimation (CSS), physical vapor deposition (PVD), vacuum evaporation, vapor transport deposition (VTD), closed space vapor transport, electrodeposition, screen printing, spray pyrolysis, metalorganic chemical vapor deposition (MOCVD), and RF sputtering. The RF sputtering method for the preparation of CdTe thin films has important advantages in that the thin films can be prepared at low growth temperatures with large-area deposition suitable for mass-production. The authors reported that the optical and electrical properties of CdTe thin film were closely connected by the thickness-uniformity of the film in the previous study [1], which means that the better optical absorbance and the higher carrier concentration could be obtained in the better condition of thickness-uniformity for CdTe thin film. The thickness-uniformity could be controlled and improved by the some process parameters such as vacuum level and RF power in the sputtering process of CdTe thin films. However, there is a limitation to improve the thickness-uniformity only in the preparation process [1]. So it is necessary to introduce the external or additional method for improving the thickness-uniformity of CdTe thin film because the cell size of thin film solar cell will be enlarged. Therefore, the authors firstly applied the chemical mechanical polishing (CMP) process to improving the thickness-uniformity of CdTe thin films with a G&P POLI-450 CMP polisher [2]. CMP process is the most important process in semiconductor manufacturing processes in order to planarize the surface of the wafer even over 300 mm and to form the copper interconnects with damascene process. Some important CMP characteristics for CdTe were obtained including removal rate (RR), WIWNU%, RMS roughness, and peak-to-valley roughness [2]. With these important results, the CMP process for CdTe thin films was performed to improve the thickness-uniformity of the sputtering-deposited CdTe thin film which had the worst two thickness-uniformities of them. Some optical properties including optical transmittance and absorbance of the CdTe thin films were measured by using a UV-Visible spectrophotometer (Varian Techtron, Cary500scan) in the range of 400 - 800 nm. After CMP process, the thickness-uniformities became better than that of the best condition in the previous sputtering process of CdTe thin films. Consequently, the optical properties were directly affected by the thickness-uniformity of CdTe thin film. The absorbance of CdTe thin films was improved although the thickness of CdTe thin film was not changed.

• Journal of Intelligence and Information Systems
• /
• v.17 no.2
• /
• pp.119-128
• /
• 2011

The Sensor technology and portable device capability able to collect recent user information and the information about the surrounding environment haven been highly developed. A user can be made use of various contents and the option is also extending with this technology development. In particular, the initial portable device had simply a call function, but now that has evolved into 'the 4th screen' which including movie, television, PC ability. also, in the past, a portable device to provided only the services of a SMS, in recent years, it provided to interactive video service, and it include technology which providing various contents. Also, it is rising as media which leading the consumption of contents, because it can be used anytime, anywhere. However, the contents available for the nature of user's handheld devices are limited. because it is very difficult for making the contents separately according to various device specification. To find a solution to this problem, the study on one contents from several device has been progressing. The contents conversion technology making use of the profile of device out of this study comes to the force and profile study has been progressing for this. Furthermore, Demand for a user is also increased and the study on the technology collecting, analyzing demands has been making active progress. And what is more, Grasping user's demands by making use of this technology and the study on the technology analyzing, providing contents has been making active progress as well. First of all, there is a method making good use of ZigBee, Bluetooth technology about the sensor for gathering user's information. ZigBee uses low-power digital radio for wireless headphone, wireless communication network, and being utilized for smart energy, automatic home system, wireless communication application and wireless sensor application. Bluetooth, as industry standards of PAN(Personal Area Networks), is being made of use of low power wireless device for the technology supporting data transmission such as drawing file, video file among Bluetooth device. With analyzing the collected information making use of this technology, it utilizes personalized service based on network knowledge developed by ETRI to service contents tailor-made for a user. Now that personalized service builds up network knowledge about user's various environments, the technology provides context friendly service constructed dynamically on the basis of this. The contents to service dynamically like this offer the contents that it converses with utilizing device profile to working well. Therefore, this paper suggests the system as follow. It collects the information, for example of user's sensitivity, context and location by using sensor technology, and generates the profile as a means of collected information as sensor. It collects the user's propensity to the information by user's input and event and generates profile in the same way besides the gathered information by sensor. Device transmits a generated profile and the profile about a device specification to proxy server. And proxy server transmits a profile to each profile management server. It analyzes profile in proxy server so that it selects the contents user demand and requests in contents server. Contents server receives a profile of user portable device from device profile server and converses the contents by using this. Original source code of contents convert into XML code using the device profile and XML code convert into source code available in user portable device. Thus, contents conversion process is terminated and user friendly system is completed as the user transmits optimal contents for user portable device.

• Korean Journal of Poultry Science
• /
• v.30 no.4
• /
• pp.259-267
• /
• 2003

Two experiments were conducted to investigate the effect of betaine on egg production, lipid metabolism, and osmoregulation in 18-to 42-week-old ISA Brown laying hens. In experiment 1, three hundred and sixty one hens were fed a com-soy basal diet contailing 16% crude protein (CP), 2800 kcal/kg metabolizable energy (ME), 0.33% methionine, and 0, 300, 600, or 1200 mg betaine per kg diet. Egg production, egg weight, feed consumption, feed conversion, and egg quality were measured every eight weeks. Betaine concentration in live and egg were determined along with serum cholesterol, abdominal fat, total serum protein and albumin levels. In experiment 2, twenty thirty-three-week-old laying hens were fed the same diets as those used in experiment 1 in individual cages and the amount of feed and water consumption were measured for two weeks. At the end of experiment 2, all birds were killed to determine blood plasma and ileal osmopressure, arginine vasotocin (AVT), and liver moisture content. In experiment 1, egg production between the treatments during the first eight weeks were not different, whereas the significant increment of egg production were noticed in the birds fed more than 600 ppm betaine after reaching the peak egg production stage (p<0.05). The egg weight was reduced significantly by the betaine supplementation for the first 8 weeks (p<0.05). Feed conversion tended to improve by betaine supplement. Egg quality was not enhanced by betaine supplementation. Liver betaine level increased with betaine feeding compared to the control but betaine concentration in eggs decreased with betaine supplementation. Betaine supplementation elevated the level of serum total cholesterol and triglyeerides compared to the control. Abdominal fat content was increased by betaine supplementation, whereas liver fat content decreased. In experiment 2, water consumption significantly increased in hens fed diets containing 300 and 600 mg betaine/kg (p<0.05) and osmotic pressure of ileal digesta increased with betaine supplement. Liver moisture content was not affected by betaine, but AVT increased in hens fed betaine. The overal results suggested the possibility of using betaine as a feed additives in the laying hens beacuse of its positive contribution to improving egg production and other metabolic parameters related to lipid metabolism.

• Korean Chemical Engineering Research
• /
• v.45 no.6
• /
• pp.656-662
• /
• 2007

Fuel reformer using plasma and shift reactor for CO oxidation were designed and manufactured as $H_2$ supply device to operate a polymer electrolyte membrane fuel cell (PEMFC). $H_2$ selectivity was increased by non-thermal plasma reformer using GlidArc discharge with Ni catalyst simultaneously. Shift reactor was consisted of steam generator, low temperature shifter, high temperature shifter and preferential oxidation reactor. Parametric screening studies of fuel reformer were conducted, in which there were the variations of the catalyst temperature, gas component ratio, total gas ratio and input power. and parametric screening studies of shift reactor were conducted, in which there were the variations of the air flow rate, stema flow rate and temperature. When the $O_2/C$ ratio was 0.64, total gas flow rate was 14.2 l/min, catalytic reactor temperature was $672^{\circ}C$ and input power 1.1 kJ/L, the production of $H_2$ was maximized 41.1%. And $CH_4$ conversion rate, $H_2$ yield and reformer energy density were 88.7%, 54% and 35.2% respectively. When the $O_2/C$ ratio was 0.3 in the PrOx reactor, steam flow ratio was 2.8 in the HTS, and temperature were 475, 314, 260, $235^{\circ}C$ in the HTS, LTS, PrOx, the conversion of CO was optimized conditions of shift reactor using simulated reformate gas. Preheat time of the reactor using plasma was 30 min, component of reformed gas from shift reactor were $H_2$ 38%, CO<10 ppm, $N_2$ 36%, $CO_2$ 21% and $CH_4$ 4%.