• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2000.08a
• /
• pp.97-100
• /
• 2000

Deadbeat property is well established in digital control system design in time domain. But in continuous time system, deadbeat is impossible because of it's ripples between sampling points. But several researchers suggested delay elements. From some specifications such as Internal model stability, physical realizations and finite time settling, unknown polynomials with delay elements in error transfer functions can be calculated. For the application to the real system, robustness property can be added. In this paper, error transfer function is specified with 1 delay element and unkown coefficients are calculated from the specs. Especially, by varying settling time and the user-specified poles, a deadbeat controller with lower order is obtained.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.2
• /
• pp.191-199
• /
• 2019

In this paper, dissimilar friction welding were produced using 15 mm diameter solid bar in chrome molybedenum steel(SCM440) to stainless steel(STS316L) to investigate their mechanical properties. Consequently, optimal welding conditions were n=2000 rpm, HP=70 MPa, UP=140 MPa, HT=10 sec and UT=10 sec when the metal loss(Mo) is 8.6 mm. In addition, an acoustic emission technique was applied to evaluate the optimal friction welding condition. AE parameters including the cumulative count, amplitude and energy showed a various changes according to the friction condition. A continuous type waveforms and low frequency spectrum was presented in friction time. On the other hand, a burst type waveform and high frequency spectrum was exhibited in pressing time.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1264-1275
• /
• 2002

This paper is concerned with the investigation on the stability and convergence characteristics of the Crank-Nicolson-Galerkin scheme that is widely being employed for the numerical approximation of parabolic-type partial differential equations. Here, we present the theoretical analysis on its consistency and convergence, and we carry out the numerical experiments to examine the effect of the time-step size △t on the h- and P-convergence rates for various mesh sizes h and approximation orders P. We observed that the optimal convergence rates are achieved only when △t, h and P are chosen such that the total error is not affected by the oscillation behavior. In such case, △t is in linear relation with DOF, and furthermore its size depends on the singularity intensity of problems.

• ETRI Journal
• /
• v.34 no.5
• /
• pp.753-758
• /
• 2012

As the next-generation video coding standard, High Efficiency Video Coding (HEVC) has adopted advanced coding tools despite the increase in computational complexity. In this paper, we propose a selective bi-prediction method to reduce the encoding complexity of HEVC. The proposed method evaluates the statistical property of the sum of absolute differences in the motion estimation process and determines whether bi-prediction is performed. A performance comparison of the complexity reduction is provided to show the effectiveness of the proposed method compared to the HEVC test model version 4.0. On average, 50% of the bi-prediction time can be reduced by the proposed method, while maintaining a negligible bit increment and a minimal loss of image quality.

• Journal of applied mathematics & informatics
• /
• v.16 no.1_2
• /
• pp.1-17
• /
• 2004

The famous Newton-Kantorovich hypothesis has been used for a long time as a sufficient condition for the convergence of Newton method to a solution of an equation in connection with the Lipschitz continuity of the Frechet-derivative of the operator involved. Using Lipschitz and center-Lipschitz conditions we show that the Newton-Kantorovich hypothesis is weakened. The error bounds obtained under our semilocal convergence result are finer and the information on the location of the solution more precise than the corresponding ones given by the dominating Newton-Kantorovich theorem, and under the same hypotheses/computational cost, since the evaluation of the Lipschitz also requires the evaluation of the center-Lipschitz constant. In the case of local convergence we obtain a larger convergence radius than before. This observation is important in computational mathematics and can be used in connection to projection methods and in the construction of optimum mesh independence refinement strategies.

• Convergence Security Journal
• /
• v.11 no.3
• /
• pp.19-24
• /
• 2011

Software failure time presented in the literature exhibit either constant monotonic increasing or monotonic decreasing, For data analysis of software reliability model, data scale tools of trend analysis are developed. The methods of trend analysis are arithmetic mean test and Laplace trend test. Trend analysis only offer information of outline content. In this paper, we discuss forecasting failure time case of failure time censoring. In this study, time series analys is used in the simple moving average and weighted moving averages, exponential smoothing method for predict the future failure times, Empirical analysis used interval failure time for the prediction of this model. Model selection using the mean square error was presented for effective comparison.

• Journal of Institute of Convergence Technology
• /
• v.8 no.1
• /
• pp.33-39
• /
• 2018

The screen printing method for forming the electrode by applying the existing pressure is difficult to apply to thin wafers, and since expensive Ag paste is used, it is difficult to solve the problem of cost reduction. This can solve both of the problems by forming the front electrode using a plating method applicable to a thin wafer. In this paper, the process conditions of electrode formation are optimized by using LIEP (Light-Induced Electrode Plating). Experiments were conducted by varying the Ni plating bath temperature $40{\sim}70^{\circ}C$, the applied current 5 ~ 15 mA, and the plating process time 5 ~ 20 min. As a result of the experiment, it was confirmed that the optimal condition of the structural characteristics was obtained at the plating bath temperature of $60^{\circ}C$, 15 mA, and the process time of 20 min. The Cu LIEP process conditions, experiments were conducted with Cu plating bath temperature $40{\sim}70^{\circ}C$, applied voltage 5 ~ 15 V, plating process time 2 ~ 15 min. As a result of the experiment, it was confirmed that the optimum conditions were obtained as a result of electrical and structural characteristics at the plating bath temperature of $60^{\circ}C$ and applied current of 15 V and process time of 15 min. In order to form Ni silicide, the firing process time was fixed to 2 min and the temperature was changed to $310^{\circ}C$, $330^{\circ}C$, $350^{\circ}C$, and post contact annealing was performed. As a result, the lowest contact resistance value of $2.76{\Omega}$ was obtained at the firing temperature of $310^{\circ}C$. The contact resistivity of $1.07m{\Omega}cm^2$ can be calculated from the conditionally optimized sample. With the plating method using Ni / Cu, the efficiency of the solar cell can be expected to increase due to the increase of the electric conductivity and the decrease of the resistance component in the production of the solar cell, and the application to the thin wafer can be expected.

• Journal of Sensor Science and Technology
• /
• v.30 no.5
• /
• pp.320-325
• /
• 2021

Biochemical oxygen demand (BOD) and chemical oxygen demand (COD) methods are conventional analytical methods to analyze water quality. Both of these methods are technically indirect measurement methods, require complicated preconditions, and are time-consuming. On the other hand, the total organic carbon (TOC) method is a direct and fast measurement method which is more intuitive and accurate than the BOD and COD methods. However, general TOC analysis methods involve complicated processes and high power consumption owing to the process of phase transition from liquid to gas by a high-temperature heater. Furthermore, periodic consumables are also required for the removal of inorganic carbon (IC). Titanium dioxide (TiO₂) is one of the most suitable photocatalysts for simple processes. Its usage involves low power consumption because it only reacts with the organic carbon (OC) without the requirement of any other reagents and extra processes. We investigated a TiO₂ photocatalyst-based TOC analysis for simple and affordable products. TiO₂-coated fiber substrate maintained under carbon included water was exposed to ultraviolet (UV) radiation of wavelength 365 nm. This method is suitable for the real-time monitoring of water pollution because of its fast reaction time. Its linear property is also sufficient to match the real value.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.9
• /
• pp.83-95
• /
• 2019

Recently, a variety of IoT data is collected by attaching geosensors to many vehicles that are on the road. IoT data basically has time and space information and is composed of various data such as temperature, humidity, fine dust, Co2, etc. Although a certain sensor data can be retrieved using time, latitude and longitude, which are keys to the IoT data, advanced search engines for IoT data to handle high-level user queries are still limited. There is also a problem with searching large amounts of IoT data without generating indexes, which wastes a great deal of time through sequential scans. In this paper, we propose a unified spatial index model that handles both grid and trajectory queries using a cell-based space-filling curve method. also it presents a visualization method that helps user grasp intuitively. The Trajectory query is to aggregate the traffic of the trajectory cells passed by taxi on the road searched by the user. The grid query is to find the cells on the road searched by the user and to aggregate the fine dust. Based on the generated spatial index, the user interface quickly summarizes the trajectory and grid queries for specific road and all roads, and proposes a Web-based prototype system that can be analyzed intuitively through road and heat map visualization.

• Composites Research
• /
• v.29 no.5
• /
• pp.276-281
• /
• 2016

Improvement of the thermal and adhesion properties of stone/wood composites was studied. Tensile test was performed for wood and stone to know the basic mechanical properties. Real-time temperature of stone and wood was measured when stone and wood was heated. To compare thermal transfer properties of stone/wood composites, two types of specimens were tested: one was stone upper whereas another was wood upper. Real time temperature measurement and lap shear test were performed to know thermal and adhesion properties by using CNT-epoxy adhesive in which CNT was dispersed in epoxy adhesive uniformly. The thermal transfer property was better for the wood upper case than stone upper case. Adding CNT improved the heat transfer as well as mechanical properties including lap shear strength.