[ $Mg_2Ni$ ]계 합금 입자의 수소저장 특성에 대한 표면처리 효과가 마이크로 전극 측정법에 의해 검토되었다. 카본-섬유로 된 마이크로 전극을 KOH 수용액 속에서 조정자를 사용하여 수소 단일입자에 접촉시켰다. 상온에서 $Mg_2Ni$ 합금의 수소저장 특성은 니켈 도금용액에 의한 표면 처리에 의해 크게 개선되었다. 니켈 도금용액 속에 있는 함유된 나트륨염(sodium phosphate 및 sodium dihydrogen citrate)이 합금을 아몰퍼스와 같은 형태로 만들었으며, 그 결과 상온에서 수소 흡장/방출 용량이 최초의 17[mAh/g]에서 150[mAh/g]로 향상되었다. 합금 입자 내에서 수소원자의 겉보기 화학적 확산계수를 계산하기 위하여 Potential-step 실험을 실시하였으며 데이터 해석을 위해 구형확산 모델을 적용하였다. 실험결과로서 겉보기 확산계수($D_{app}$)는 수소 흡장 및 방출되는 전 과정에서 $10^{-8}{\sim}10^{-9}[cm^2/s]$ 수준인 것으로 확인되었다.
Purpose: This study aims to evaluate the applicability of a tractor-baler system equipped with a newly developed round baler by conducting stability analyses via static-state mathematical simulations and verification experiments for the tractor equipped with a loader. Methods: The centers of gravity of the tractor and baler were calculated to analyze the transverse overturning of the system. This overturning of the system was analyzed by applying mathematical equations presented in previous research and comparing the results with those obtained by the newly developed mathematical simulation. For the case of the tractor equipped with a loader, mathematical simulation results and experimental values from verification experiments were compared and verified. Results: The center of gravity of the system became lower after the baler was attached to the tractor and the angle of transverse overturning of the system steadily increased or decreased as the deflection angle increased or decreased between $0^{\circ}$ and $180^{\circ}$ on the same gradient. In the results of the simulations performed by applying mathematical equations from previous research, right transverse overturning occurred when the tilt angle was at least $19.5^{\circ}$ and the range of deflection angles was from $82^{\circ}$ to $262^{\circ}$ in counter clockwise. Additionally, left transverse overturning also occurred at tilt angles of at least $19.5^{\circ}$ and the range of deflection angles was from $259^{\circ}$ to $79^{\circ}$ in counter clockwise. Under the $0^{\circ}$ deflection angle condition, in simulations of the tractor equipped with a loader, transverse overturning occurred at $17.9^{\circ}$, which is a 2.3% change from the results of the verification experiment ($17.5^{\circ}$). The simulations applied the center of gravity and the correlations between the tilt angles, formed by individual wheel ground contact points excluding wheel radius and hinge point height, which cannot be easily measured, for the convenient use of mathematical equations. The results indicated that both left and right transverse overturning occurred at $19.5^{\circ}$. Conclusions: The transverse overturning stability evaluation of the system, conducted via mathematical equation modeling, was stable enough to replace the mathematical equations proposed by previous researchers. The verification experiments and their results indicated that the system is workable at $12^{\circ}$, which is the tolerance limit for agricultural machines on the sloped lands in South Korea, and $15^{\circ}$, which is the tolerance limit for agricultural machines on the sloped grasslands of hay in Japan.
The goal of this study is to provide basic data to establish a foundation for the provision of safe drinkable water. The raw water of natural mineral water was analyzed to determine the quantities of anions (F-, Cl-, NO3-N-, and SO42- ) and cations (Ca2+, K+, Mg2+, and Na+) during the former and latter half of 2016. Analysis of the current quality of the raw water of natural mineral water among domestic manufacturers showed average anions contents of 0.46mg/L of fluorine, 8mg/L of chlorine ion, 1.5mg/L of nitrate nitrogen, and 12mg/L of sulfate ion. While the fluorine content was greater than the water quality criterion of 2.0mg/L at four points, the fluorine level was overall stable. The average cations contents included 21.3mg/L of calcium, 1.0mg/L of potassium, 3.4mg/L of magnesium, and 9.6mg/L of sodium. The chemical characteristics were compared among the major ions, and the results are presented in a piper diagram. The content ratio of cations was in the order of Ca2+> Na+>Mg2+>K+, whereas that of anions was in the order of SO42->Cl->NO3-N->F-. While the cations were slightly scattered, the anions were generally concentrated except for at a few points. The Ca-Na-HCO3 type was dominant overall in water sources from diorite, gneiss, and granite, while the Na-Mg-Ca-HCO3-Cl type was dominant in basalt sources. Mineral water manufacturers source their water under various conditions, including in-hole casing, excavation depth, and contact state of bedrock; even within the same rocky area, some differences in the water quality type can occur. When the depth of the water source was taken into account, the mean anions contents of F-, Cl-, NO3-N-, and SO42- were similar, with no significant differences according to depth. Of the cations, K+ and Na+ showed no significant differences across all the tubular wells, whereas Ca2+ and Mg2+ decreased in content with depth.
어업 종사자들은 기계화의 진전으로 인한 빈번한 기계사용과 자연이나 동식물의 직접적인 접촉으로 인하여 작업 중 재해나 질병의 위험이 다른 직종에 비해서 결코 작지 않으며, 인력이 고령화되는 것은 산업안전 및 의건 분야에 있어서 질병이나 재해가 증가할 수 있다는 가능성을 강력하게 시사한다고 할 수 있다. 따라서 어업에 대한 안전 및 보건 실태 파악과 이에 대한 대책을 마련할 필요성이 있다. 본 연구는 영동지역 동해안의 대표적인 어항인 주문진, 거진항을 중심으로 배가 들어오는 새벽 6시에서 마지막 배가 들어오는 오전 11시까지 어획한 물고기를 하역한 후 뒷정리를 하는 근로자들을 대상으로 산재현황에 대해 설문조사를 실시하였다. 전체 응답자는 96명이었다. 설문 결과 어업 작업 중 사고가 있었다고 응답한 경우가 7명이었고 그 중에서도 4일 이상 입원하였다고 한 경우도 5명으로 5.2%였다. 부상 종류는 골절상이 1명, 손가락 절단이 2명, 타박상이 4명이었다. 부상 원인은 안전의식 부족과 작업 조건 불안정으로 풀이된다. 따라서 작업 과정에서 나타나는 유해인자, 특히 인간공학적 측면에서의 대책과 평가가 중요하며 이를 위해서는 좀 더 규모가 큰 추후연구가 필요하다. 아직까지 1차 산업에 대한 안전 및 보건 분야에 대한 연구가 부족한 현실이며 근로자의 건강을 보호하기 위한 제도적 장치가 미비하다. 이 연구결과를 토대로 어업에 종사하는 근로자에 대해 지속적인 관심을 갖고 현실적인 대책을 구체화시킬 필요가 있다.
지반조사에서 비파괴 조사 기술은 시추조사보다 경제적으로 비용이 덜 들고 광역에 걸친 지반정보를 제공하는 장점이 있다. 하지만 지반설계정수로서 적용하기에는 어려운 한정된 정보만을 제공하게 된다. 이를 극복하기 위해, 비파괴 조사 방법 중 하나인 전기비저항 탐사를 모형토조실험에 적용하여, 토질상태에 따른 비저항 반응과 함수비에 따른 비저항 반응을 분석하여 비저항 거동 양상에 대한 연구를 수행하였다. 실험에 사용한 토질은 주문진 표준사, 마사토이며 각 토질의 입도 분포, 균등계수를 구하여 실험에 있어 실험재료의 균질한 상태를 유지하였다. 실험에 사용한 모형의 제원은 $160{\times}100{\times}50$ (cm)의 아크릴 재질 토조이며, 각 토질의 높이는 30 cm를 유지하였다. 5TE(함수비측정센서)센서를 7 ~ 8cm 간격으로 수직하게 꽂아 층별 함수비를 측정하였다. 모형실험 결과 주문진 표준사는 비저항 거동 양상이 함수비에 민감하게 반응하는 것을 알 수 있었으며, 마사토는 함수비에 따라 비저항이 낮아진 후에도 시간경과에 따른 거동 양상에 큰 변화가 없는 것을 관찰하였다. 또한 토조 실험에 사용된 토양과 유사한 테스트 베드를 선정하여 그 반응을 비교 분석하였다. 이러한 실험을 통해 토질 상태와 함수비에 따른 다양한 비저항 거동 양상 자료를 수집하고, 비파괴 조사기술의 정확도를 향상 시켜 나간다면 지반설계정수를 산정하는데 있어 기초적인 연구가 될 수 있음을 확인하였다.
본 논문에서는 SOFC 금속연결재로서 Crofer22APU를 적용하고자 표면에 전도성 산화막($La_{0.8}Sr_{0.2}CoO_3$)을 습식코팅 후, SOFC 작동환경에서 산화거동, 전기적 특성변화 및 미세구조 변화를 관찰하였다. 코팅 전 샌드블러스트 장치를 이용한 Crofer22APU 표면처리를 통하여 코팅막/금속의 접합특성을 개선시킬 수 있었으며, 320 mesh의 입자크기를 갖는 알루미나 분말을 이용하여 표면처리한 경우 접착특성이 극대화되었다.$La_{0.8}Sr_{0.2}CoO_3$ 코팅된 시편의 전기적 특성 평가는 4-wire 법을 이용하여 SOFC 작동환경에서 약 4,000 시간 장기성능 평가하였으며 $12mW{\cdot}cm^2$의 낮은 면저항값을 얻을 수 있었다. 실험종료 후 미세구조 분석결과에서도 전도성 산화막($La_{0.8}Sr_{0.2}CoO_3$) 코팅이 금속의 부식으로 인한 산화층의 생성속도를 늦추고 이로 인한 금속의 전기적 특성이 감소하는 것을 방지하는데 유효함을 확인하였다.
초연결사회의 시대가 도래하여 시간과 공간의 제약없이 효율적으로 정보를 전달할 수 있는 스마트 디바이스의 사용이 보편화되었다. 스마트 디바이스는 사람과 사물 간의 상호작용을 통하여 정보를 전달할 수 있도록 점차 웨어러블 형태로 발전하고 있으며, 의복 형태의 스마트 디바이스인 스마트의류는 인체에 가장 밀착한 상태로 각종 생체신호 등의 측정이 가능하기 때문에 미래 일상생활에서 사용도가 높아질 것으로 주목받고 있다. 기존에 개발된 스마트의류는 의복에 전자장치를 부착한 형태로 개발되어 기기 이물감으로 인해 착용 시 사용자의 불편을 야기하여 지속적으로 생체신호를 측정하기에 한계가 있었다. 이에 따라 점차 전자장치가 텍스타일 내의 한 요소로 통합되어 있는 스마트 텍스타일을 기반으로 한 스마트의류의 개발이 요구된다. 본 연구에서는 현재 소비자에게 가장 근접한 웨어러블 디바이스인 스마트워치 사용자를 대상으로 하여 사용경험에 기반한 감성을 통해 웨어러블 디바이스에서 사용자가 필요로 하는 요구조건을 탐색하고자 하였다. 스마트워치 사용자의 경험에 기반한 감성에 대해 구체적인 답변을 얻고자 반구조화 된 심층인터뷰를 통해 질적 연구를 수행하였으며, 심층인터뷰 내용을 바탕으로 사용자감성을 기능적, 심미적, 사회적, 경험적 네 가지 측면으로 분류하였다. 측면별로 감성키워드를 설정하여 빈도 수 확인을 통해 스마트워치 사용자의 관심도를 알아보았다. 본 연구의 결과를 미래의 웨어러블 디바이스로 주목받고 있는 스마트의류 제작에 필요한 스마트 텍스타일 개발을 위한 기초자료로 활용하고자 한다.
Three different white cast irons alloyed with Cr, V, Mo and W were prepared in order to study their abrasion wear behavior in as-cast and heat-treated conditions. The specimens were produced using a 15㎏-capacity high frequency induction furnace. Melts were super-heated to $1600^{\circ}C$, and poured at $1550^{\circ}C$ into Y-block pepset molds. Three combinations of the alloying elements were selected so as to obtain the different types of carbides : 3%C-10%Cr-5%Mo-5%W(alloy No. 1: $M_7C_3$ and $M_6C$), 3%C -10%V-5%Mo-5%W(alloy No. 2: MC and $M_2C$) and 3%C-17%Cr-3%V(alloy No. 3: $M_7C_3$ only). A scratching type abrasion test was carried out in the states of as-cast(AS), homogenizing(AH), air-hardening(AHF) and tempering(AHFT). First of all, the as-cast specimens were homogenized at $950^{\circ}C$ for 5h under the vacuum atmosphere. Then, they were austenitized at $1050^{\circ}C$ for 2h and followed by air-hardening in air. The air-hardened specimens were tempered at $300^{\circ}C$ for 3h. 1 ㎏ load was applied in order to contact the specimen with abrading wheel which was wound by 120 mesh SiC paper. The wear loss of the test piece(dimension: $50{\times}50{\times}5$ mm) was measured after one cycle of wear test and this procedure was repeated up to 8 cycles. In all the specimens, the abrasion wear loss was found to decrease in the order of AH, AS, AHFT and AHF states. Abrasion wear loss was lowest in the alloy No.2 and highest in the alloy No.1 except for the as-cast and homogenized condition in which the alloy No.3 showed the highest abrasion wear loss. The lowest abrasion wear loss of the alloy No.2 could be attributed to the fact that it contained primary and eutectic MC carbides, and eutectic $M_2C$ carbide with extremely high hardness. The matrix of each specimen was fully pearlitic in the as-cast state but it was transformed to martensite, tempered martensite and austenite depending upon the type of heat-treatment. From these results, it becomes clear that MC carbide is a significant phase to improve the abrasion wear resistance.
Halogen free intumescent flame retardants(IFRS), such as the mixture of melamine phosphate(MP) and char forming agents(pentaerythritol(PER), di-pentaerythritol(DiPER), tris(2-hydroxyethyl) isocyanurate(THEIC)), were prepared and characterized. Polypropylene(PP)/$IFR_S$ composites were also prepared in the presence of ethylene diamine phosphate(EDAP) as a synergist and used into flame retardant PP powder coatings. Thermoplastic PP powder coatings at 20 wt% flame retardant loading were manufactured by extruded and then mechanical cryogenic crushed to bring them in fine powder form. These intumescent flame retardant powder coatings($IFRPC_S$) were applied on mild steel surface for the purpose of protection and decorative. It is a process in which a $IFRPC_S$ particles coming in contact with the preheated mild steel surface melt and form a thin coating layer. The obtained MP flame retardant was analyzed by utilizing FTIR, solid-state $^{31}P$ NMR, ICP, EA and PSA. The mechanical properties as tensile strength, melt flow index(MFI) and the thermal property as TGA/DTA and the fire safety characteristics as limiting oxygen index(LOI), UL94 test, SEM were used to investigate the effect of $IFRPC_S$. The experimental results show that the presence of $IFR_S$ considerably enhanced the fire retardant performances as evidenced by the increase of LOI values 17.3 vol% and 32.6 vol% for original PP and $IFRPC_S$-3(PP/MP-DiPER/EDAP), respectively, and a reduction in total flaming combustion time(under 15 sec) in UL94 test of $IFRPC_S$. The prepared $IFRPC_S$-3 have good comprehensive properties with fire retardancy 3.2 mm UL94 V-0 level, LOI value 32.6%, tensile strength $247.3kg/cm^2$, surface roughness Ra $0.78{\mu}m$, showing a better application prospect. Through $IFRPC_S$-2(PP/MP-PER/EDAP) and $IFRPC_S$-3 a better flame retardancy than that of the $IFRPC_S$-1(PP/MP/EDAP) was investigated which was responsible for the formed more dense and compact char layer, improved synergy effect of MP and PER/DiPER.
우리나라도 이제는 범죄피해자의 보호 지원을 위한 질 높은 서비스를 제공할 만큼 경제적 성장을 이루었다고 본다. 지금까지는 법무부에서 범죄피해자 보호 지원업무를 전담해오다가 최근 경찰청에서도 범죄피해자 보호 지원을 경찰의 주요 업무로 인식하고 각종 서비스를 제공하고 있다. 사실 형사단계로 본다면, 검찰과 법무부보다는 사건직후 피해자를 처음 접하는 경찰에서 즉각적인 범죄피해자 보호 지원을 하는 것이 바람직하기는 하다. 문제는 법령과 제도 상 경찰은 서비스제공에 한계가 있지만, 경찰의 피해자 보호 지원의 중요성을 감안할 때, 민관협동 형태의 범죄피해자 보호 지원 모델을 탐색해볼 필요가 있다. 물론, 우선 법무부의 민관협동 체제와의 새롭게 관계정립이 필요하고, 경찰의 특성을 살려서 피해자에게 제공할 수 있는 서비스의 내용을 정비하고 민관협동 형태로 간다면, 어디까지 경찰에서 서비스를 제공할 것인지 방향도 정해질 것이다. 선진국의 경우 경찰과 민간기구의 상호 협조가 매우 긴밀하게 이루어지고 있으며, 이는 범죄피해자에게 실질적인 보호와 지원의 성과로 나타나고 있다. 이에 본 연구는 경찰단계에서 범죄피해자 보호 지원의 문제점을 검토해보고, 그 개선방안에 대하여 다음과 같이 제시하였다. 첫째는 범죄피해자 보호지원에 있어서 가장 먼저 접하는 경찰의 역할을 재정립하는 것이고, 둘째는 경찰서별로 피해자전담경찰관과 피해자 보호사 등의 상시 협력체계를 구축하는 것이며, 셋째는 경찰단계에서 피해자보호지원이 가능한 서비스의 종류를 개발하는 것이고, 넷째는 범죄피해자의 임시숙소 또는 신변보호를 위한 안전지대의 기능을 담당할 피해자종합지원센터를 전국적으로 개소하는 방안, 다섯째는 지역권내에 범죄피해자의 보호지원을 위한 유관기관 담당자로 구성된 솔루션회의의 정례화, 여섯째는 범죄피해자의 보호는 경찰 등의 국가기관에서, 범죄피해자에 대한 지원은 지방자치 단체의 복지부서에서 담당하고 종합적으로 사후관리하는 방안을 제시하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.