• 제어로봇시스템학회논문지
• /
• 제6권3호
• /
• pp.329-337
• /
• 2000

This study describes a pressure tracking control of hydroforming process which is used for precision forming of sheet metals. The hydroforming operation is performed in the high-pressure chamber strictly controlled by pressure control valve and by the upward motion of a punch moving at a constant speed, The pressure tracking control is very difficult to design and often does not guarantee satisfactory performances be-cause of the punch motion and the nonlinearities and uncertainties of the hydraulic components. To account for these nonlinearities and uncertainties of the process and iterative learning controller is proposed using Cerebellar Model Arithmetic Computer (CMAC). The experimental results show that the proposed learning control is superior to any fixed gain controller in the sense that it enables the system to do the same work more effectively as the number of operation increases. In addition reardless of the uncertainties and nonlinearities of the form-ing process dynamics it can be effectively applied with little a priori knowledge abuot the process.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1053-1060
• /
• 2006

This paper consider an initially deformed state caused by the pressurized fluid flowing through the pipe at a constant velocity. When the initial forte is neglected in curved pipes, the natural frequencies are reduced as flow velocity increases. However, when the initial tension took into account, the natural frequencies are not changed with the change of the flow velocity. As the internal pipe pressure is increased the natural frequencies are also slightly increased. In free vibrational simulation of piping systems in petrochemical plants, it is necessary to calculate the initial state force due to the velocity and the pressure of the fluid flow from the equilibrium first, then the force should be included in the equation of motion of the systems to get more accurate natural frequencies. In this study, calculate the mass matrix and stiffness matrix of piping system by MATLAB

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.590-594
• /
• 2004

In this study, lead-free piezoelectric ceramics were investigated for pressure sensor applications as a function of the amount of $CeO_2$ addition at Bi(Na,K)$TiO_3-SrTiO_3$ system. With increasing the amount of $CeO_2$ addition, the density and dielectric constant increased. Electromechanical coupling factor($k_p$) showed the maximum value(kp, 0.39) at 0.1wt% $CeO_2$ addition and decreased above 0.1wt% $CeO_2$ addition., Density, dielectric constant(${\varepsilon}_r$) increased but mechanical quality factor(Qm), piezoelectric constant(d33) decreased in $CeO_2$ addition, respectively.

• 터널과지하공간
• /
• 제31권4호
• /
• pp.243-269
• /
• 2021

2010년대 이후 고준위 방사성폐기물 심층처분, 지하 CO₂ 저장과 시추공 조사 기반 심지층 특성화를 대상으로 한 연구 및 실용화 프로젝트의 사회적 중요성이 점차 높아지고 있다. 이와 관련하여, 대심도 암반의 수리 특성에 대한 정량적이고 신뢰성있는 정보를 얻을 수 있는 현장 시험 기술의 필요성도 크게 증가하고 있다. 수년간의 연구 개발을 통해 자체 기술력으로 설계, 제작된 핵심 장치들을 기반으로 대심도 시추공 수리특성 조사 시스템(DHTS)을 독자적으로 구축하였다. 이 시스템을 사용하여 경주시 중생대 화강암과 퇴적암 지역에 위치한 심도 1 km 급 시추공 2개소에서 고정밀도 정압 주입시험을 성공적으로 수행하였다. 현장 시험에서 미세 유량 주입/조절 모듈을 사용하여 0.01 l/min 미만의 매우 낮은 유량 측정이 가능하였다. 본 논문에서는 DHTS의 주요 특성을 소개하고 대심도 저투수성 암반 환경 하에서 수행된 고정밀도 시험 결과에 대해 간단히 논의하였다.

• Transactions on Electrical and Electronic Materials
• /
• 제13권6호
• /
• pp.273-277
• /
• 2012

The vacuum drying process for drying of paper in current transformers was modeled with an aim to develop an understanding of the drying mechanism involved and also to predict the water collection rates. A molecular as well as macroscopic approach was adopted for the prediction of drying rate. Ficks law of diffusion was adopted for the prediction of drying rates at macroscopic levels. A steady state and dynamic mass transfer simulation was performed. The bulk diffusion coefficient was calculated using weight loss experiments. The accuracy of the solution was a strong function of the relation developed to determine the equilibrium moisture content. The actually observed diffusion constant was also important to predict the plant water removal rate. Thermo gravimetric studies helped in calculating the diffusion constant. In addition, simulation studies revealed the formation of perpetual moisture traps (loops) inside the CT. These loops can only be broken by changing the temperature or pressure of the system. The change in temperature or pressure changes the kinetic or potential energy of the effusing vapor resulting in breaking of the loop. The cycle was developed based on this mechanism. Additionally, simulation studies also revealed that the actual mechanism of moisture diffusion in CT's is by surface jumps initiated by surface diffusion balanced against the surrounding pressure. Every subsequent step in the cycle was to break such loops. The effect of change in drying time on the electrical properties of the insulation was also assessed. The measurement of capacitance at the rated voltage and one third of the rated voltage demonstrated that the capacitance change is within the acceptance limit. Hence, the new cycle does not affect the electrical performance of the CT.

• 한국분무공학회지
• /
• 제17권3호
• /
• pp.113-120
• /
• 2012

It is being more serious problems that the pollutant and the greenhouse gas emitted from the internal combustion engines due to the increasing demand of automobiles. To counteract this, as one of the ways has been studied, GDI type engine, which is directly injected into the combustion chamber and burns by a spark ignition that chose the merits of both gasoline engine and diesel engine, was appeared. The combustion phenomena in this GDI engine is known to contribute to combustion stability, fuel consumption reduction and reductions of harmful substances of exhaust gas emission, when the fuel spray of atomization being favorable and the mixture formation being promoted. Accordingly, this study analyzed the affection of ambient temperature and fuel injection pressure to the fuel by investigate the visualization of combustion, combustion pressure and the characteristic of emission, by applying GDI system on the constant combustion chamber. As a result, as the fuel injection pressure increases, the fuel distribution in the combustion chamber becomes uniform due to the increase of penetration and atomization. And when ambient temperatures in the combustion chamber become increase, the fuel evaporation rate being high but the penetration was reduced due to the reduction of volume flux, and confirmed that the optimized fuel injection strategy is highly needed.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.962-967
• /
• 1991

A counter balance valve is used as one part of hydraulic motor brake system. The function of this valve is to protect over-run or free falling of inertia load. But occasionally the brake system with counter balance valve makes some undesirable problems such as pressure surges or vibrations. In this study, for the purpose of easy estimation about dynamic characteristics of hydraulic system including counter balance valve, precise formulation describing fluid dynamics and valve dynamics under various boundary conditions were made. Dynamic characteristics were analysed by numerical integration using Runge-Kutta method, because the equations in this circuit with counter balance valve contain various nonlinear terms. Propriety of this analysis method is verified by experiment. For the purpose of obtaining fundamental data for preventing instability, this study experimented the effects of the spool taper, spring constant, cylindrical choke. And we developed double acting brake system integrated counter balance valve.

• 한국시스템다이내믹스연구
• /
• 제12권1호
• /
• pp.89-114
• /
• 2011

With steady increase in the demand for door-to-door delivery services, courier service providers are facing a constant pressure to reduce delivery price in order to secure quantity order and to improve the efficiency and reliability for customer service. The objective of this research is to explain the structure of the door-to-door delivery including door-to-door delivery service demand, sorting capacity in the hub-terminal, and the system performance measures such as service reliability networks using causal loop diagram(CLD). Based on causal relation, this research describes a comprehensive approach to examine how capacity reliability contributes to the renewal of the firm's competences through its reciprocal relationship with travel time reliability and connectivity reliability. Also, this research suggests the policy alternatives to improve effectiveness and efficiency of door-to-door delivery network in response to increase customer satisfaction and profit maximization of the courier service providers: operational, tactical, and strategic levels.

• 전기전자학회논문지
• /
• 제18권3호
• /
• pp.420-426
• /
• 2014

본 연구에서는 저온유동성 성능검사 시스템 구현을 통해 디젤 차량용 통합형 연료필터의 성능을 평가한다. 저온유동성시험 장치의 시험조건은 경유(또는 등유)를 사용하고, 상온, -20 및 $-30^{\circ}C$ 에서 경유공급압력 $3.4kgf/cm^2$, 연료공급량 60 l/H, 설정전류 30 A 및 전압은 $13V_{dc}$를 사용한다. 시료시험으로 통합필터를 지그에 장착하고, 경유(또는 등유)를 일정압력과 유량으로 설정하여 챔버 탱크와 필터에 채운 후, 설정시간 동안 설정온도로 냉각한 후, 필터 전후에 따라 유압과 시동시간, 히터의 소모전류 및 전력을 측정한다.

• 한국자동차공학회논문집
• /
• 제19권6호
• /
• pp.140-147
• /
• 2011

The injection nozzle of an electro-hydraulic injector for the common rail Diesel fuel injection system is being opened and closed by movement of a injector's needle which is balanced by pressure at the nozzle seat and at the needle control chamber, at the opposite end of the needle. In this study, the slenoid actuator was considered as a prime movers in high pressure Diesel injector. Namely a solenoid-driven Diesel injector with different driving current types, as a general method driven by solenoid coil energy, has been applied with a purpose to develop the analysis model of the solenoid actuator to predict the dynamics characteristics of the hydraulic component (injector) by using the AMESim code. Aimed at simulating the hydraulic behavior of the solenoid-driven injector, the circuit model has been developed as a unified approach to mechanical modeling in this study. As this analytic results, we know the suction force and first order time lag for driving force can be endowed in solenoid-driven injector in controlling the injection rate. Also it can predict that the input current wave exerted on solenoid coil is the dominant factor which affects on the initial needle behavior of solenoid-driven injector than the hydraulic force generated by the constant injection pressure.