• 한국지반공학회논문집
• /
• 제19권6호
• /
• pp.227-243
• /
• 2003

강관말뚝의 속채움 콘크리트 B방법에서 미끌림방지턱의 구조적인 특성을 알아보기 위하여, 강관말뚝머리의 내부에 미끌림방지턱을 설치하지 않은 시험체와 2단의 곡률 강편 미끌림방지턱을 강관말뚝내부에 용접한 시험체(시방서 방법), 그리고 미끌림방지턱을 다수의 곡률 강편과 고장력볼트로 체결한 시험체(개발형 방법)에 대하여 실물크기 인발 및 압발 실험을 수행하였다. 그 결과, 미끌림방지턱이 없는 시험체는 최대인발하중 15.6tonf에서, 최대압발하중 27.57tonf에서 콘크리트의 화학적 부착파괴가 발생하였다. 그리고 미끌림방지턱이 있는 시방서 방법과 개발형 방법의 시험체는 없는 시험체보다 최대인발하중의 약 8.9배와 최대압발하중의 6.2배 크게 나타났다. 또한 시방서 방법과 개발형 방법의 하단 미끌림방지턱에 대한 하중분담비율은 거의 동일한 거동을 보인 반면에, 상단 미끌림방지턱은 시방서방법보다 개발형 방법의 하중분담비율이 크게 기여하였다. 그리고 시방서 방법과 개발형 방법의 미끌림방지턱 형상에 의한 합성작용과 구조성능은 거의 동일하였다.

• 정보처리학회논문지B
• /
• 제19B권4호
• /
• pp.221-224
• /
• 2012

복수객체의 윤곽추출을 위해 스네이크를 분리하고 연결하는 대표적인 방법이 스네이크 포인트의 거리를 이용한 최소거리방법이다. 이 방법은 객체 위상에 따라 스네이크를 분리하지 못하는 경우가 발생한다. 본 논문에서는 스네이크를 분리하지 못하는 경우를 실험적으로 증명하고 스네이크 세그먼트의 벡터를 이용한 새로운 방법이 스네이크를 성공적으로 분리 및 연결함을 실험적으로 보임으로써 최소거리방법의 문제점을 해결하였다. 하나의 영상 안에 3개 및 5개 객체가 있는 실험영상에 실험을 하여 제안한 방법이 우수하다는 것을 보여준다.

• 대한전자공학회논문지
• /
• 제24권4호
• /
• pp.610-617
• /
• 1987

This thesis is concerned with fault-tolerance of a B-net (Beta-network) which is a kind of interconnection network in the multicomputer system. In this paper, a method for obtaining Maximal Tolerable Fault Set(MTFS) of link line connecting switching elements in the arbitrary B-net is presented. Using this method, it is seen that testing of DFA capability is possible when s-a-faults of link line occur, and criterion for determining degree of fault- tolerance of a B-net in terms of link line is introduced.

• 대한전자공학회논문지
• /
• 제25권1호
• /
• pp.1-7
• /
• 1988

A new type broadband channel dropping filter which has a potential use as a millimeter-wave multiplexer has been realized by properly connecting 3-dB directional couplers and bandstop filters. 90\ulcorner3-dB directional couplers have been designed using two nonuniformly coupled dielectric image guides, while bandstop filters with Chebyshev passbands have been designed using dielectric image-guide grating structure. Effective dielectric constant method has been aplied to the image-guide dispersion analysis and to the design of bandstop gratings and 3-dB couplers. Experimental results in excellent agreement with computed responses are demonstrated.

• 한국자동차공학회논문집
• /
• 제2권5호
• /
• pp.1-10
• /
• 1994

By applying of total electric capacitance method on engine connecting rod bearing during engine operating, the influence of engine operating conditions and lubricants on bearing oil film thickness was investigated. Minimum oil film thickness increases with kinematic viscosity, but as increasing of viscosity, the increasing ratio of film thickness is reduced. Also minimum oil film thickness increases with engine speed but there is a limit. Above this limit, film thickness decreases in opposition because of crankshaft inertia. As increasing of engine torque and oil temperature, munimum oil film thickness decreases linearly. For non-Newtonian oils, the correlation between $100{\circ}C$ kinematic viscosity and munimum oil film thickness is very poor.

• International Journal of Clinical Preventive Dentistry
• /
• 제14권4호
• /
• pp.247-255
• /
• 2018

Objective: Osseointegration is essential process for successful implants and effects to implant in long term, therefore, passive fitness of good prosthesis is necessary. To make a good prosthesis, at first it should be done a sectioned casting and then joined method of sectioned casting body is recommended. Methods: In this study, to provide the fundamental data on stable connection method for successful implants, the author tested fitness of casting body, and compared difference between gas soldering technique and laser welding technique. Results: In fitness test of 2 abutment (test A, C), gas soldering group's fitness in the opposite part of connection was worse than laser welding group. In fitness test of 3 abutment (test B, D), gap distance was increased both in gas soldering technique and laser welding technique. Gap distance at the connecting part and the opposite part of the abutment in gas soldering technique was worse than laser welding technique and the more additional abutment, the worse gap distance in gas soldering technique. In fitness test of 3 abutment (test B, D), there's little variation in No. 2 abutment when connecting soldering process was done and there's little influence on already soldered connection part when the additional soldering connection was done. Conclusion: On weak loading condition and the part which is needed an accuracy, laser welding technique is more effective and on long-span prosthesis and frequent chewing loading part, laser welding technique is recommended first and applying additional gas soldering technique would be better for making much more successful prosthesis.

• 한국통신학회논문지
• /
• 제15권5호
• /
• pp.426-433
• /
• 1990

본 연구는 2B+D ISDN 기본 액세스 트래픽을 집선하는 통합형 집선장치를 제안하고 분리형 집선방식과의 비교를 수행한다. 이 시스템의 특성을 비트속도 종류별로 출력 채널수, 가입자수, 인가된 트래픽 양 등의 매개변수에 의해 분석하였다. 분석 결과 여기에 제안한 집선 방식이 CCITT가 권고한 단순 다중화 방식이나 분리형 집선 방식에 비하여 T1 캐리어에 의해 시스템에 연결 가능한 ISDN 기본 액세스 가입자수를 확실히 증가시킨 결과를 보인다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 동계학술발표대회 논문집
• /
• pp.10-10
• /
• 2006

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.362-364
• /
• 2003

Generally, photovoltaic system is composed a number of solar cells array. so, virtual implementation module for solar cell array is needed Parallel connection each module for extract the power. A desirable characteristic of a parallel supply system is that individual converters share the load current equally and stably. The current sharing(CS) can be implemented using two approaches. The first one, known as a droop method, relies on the high output impedance of each converter. and The second approach, known as active current-sharing techniques. In this paper, analyze for better control logic of parallel connecting virtual implements of solar cell at using droop method.

• 한국의류산업학회지
• /
• 제13권5호
• /
• pp.661-671
• /
• 2011

This study was designed to produce rounded belt pattern and tight-skirt pattern drafting method using 3D body scan data. Subjects were thirty women in their early twenties. In order to figure out the optimum cutting points, namely, where darts are made, using CAD program, curve ratio inflection points on the horizontal curve of waist, abdomen, and hip to find 1 point in the front, two points in the back part. The average length from center front point to maximum curve ratio was 7.7 cm(46.3%) on the waist curve; 7.9 cm(39.4%) on the abdomen curve. And the average length from center back point to maximum curve ratio point was 6.9 cm(39.0%) for first dart and 11.2 cm(63.3%) for second dart on the waist curve; 8.9 cm(35.8%) for first dart and 15.7 cm(63.3%) for second dart on the hip curve respectively. The cutting lines from were made up by connecting curve inflection points. After divided using cutting lines, each patch was flattened onto the plane and all the technical design factors related with patternmaking were measured, such as dart amount, lifting amount of side waist point, etc. Based on the results of correlation analysis among these factors, regression analysis was done to produce equations to estimate the variables necessary to draw up pattern draft method; F1=F8+1.1, $F4=2.5{\times}F2+0.9$, $F5=0.9{\times}F4+1.0$, $F6=0.3{\times}F4+0.4$, $B1=0.9{\times}B8+2.3$, $B4=2.1{\times}B2+1.3$, $B5=0.9{\times}B4+3.5$, and $B6=0.3{\times}B4+0.4$.