• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.227-243
• /
• 2003

To find the structural characteristics of non-slip device in connecting method B between steel pipe pile and concrete footing, compression and uplift test was performed for full sized specimens not having non-slip device, those having non-slip device with two curved steel plate bars welded inside the steel pipe pile(standard method), and those having non-slip device with serveral curved steel plate bars bolted inside the steel pipe pile(new method). As a result, specimens not having non-slip device had chemical debonding failure at 15.6tonf of peak uplift load and 27.57tonf of peak compression load. And the standard method and the new method showed about 8.9 times of peak uplift load and 6.2 times of peak compression load higher than specimens not having non-slip device. The load transfers of lower non-slip devices of the standard method and the new method were similar in behavior, while the higher non-slip device of the new method showed higher ratio of load transfer than that of the standard method. And these two methods had nearly the same composite action and structural capacity caused by non-slip devices.

• The KIPS Transactions:PartB
• /
• v.19B no.4
• /
• pp.221-224
• /
• 2012

The most famous algorithm of splitting and connecting Snake for extracting the boundary of multiple objects is the nearest method using the distance between snake points. It often can't split and connect Snake due to object topology. In this paper, its problem was discussed experimentally. The new algorithm using vector between Snake segment is proposed in order to split and connect Snake with complicated topology of objects. It is shown by experiment of two test images with 3 and 5 objects that the proposed one works better than the nearest one.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.4
• /
• pp.610-617
• /
• 1987

This thesis is concerned with fault-tolerance of a B-net (Beta-network) which is a kind of interconnection network in the multicomputer system. In this paper, a method for obtaining Maximal Tolerable Fault Set(MTFS) of link line connecting switching elements in the arbitrary B-net is presented. Using this method, it is seen that testing of DFA capability is possible when s-a-faults of link line occur, and criterion for determining degree of fault- tolerance of a B-net in terms of link line is introduced.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.1
• /
• pp.1-7
• /
• 1988

A new type broadband channel dropping filter which has a potential use as a millimeter-wave multiplexer has been realized by properly connecting 3-dB directional couplers and bandstop filters. 90\ulcorner3-dB directional couplers have been designed using two nonuniformly coupled dielectric image guides, while bandstop filters with Chebyshev passbands have been designed using dielectric image-guide grating structure. Effective dielectric constant method has been aplied to the image-guide dispersion analysis and to the design of bandstop gratings and 3-dB couplers. Experimental results in excellent agreement with computed responses are demonstrated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.5
• /
• pp.1-10
• /
• 1994

By applying of total electric capacitance method on engine connecting rod bearing during engine operating, the influence of engine operating conditions and lubricants on bearing oil film thickness was investigated. Minimum oil film thickness increases with kinematic viscosity, but as increasing of viscosity, the increasing ratio of film thickness is reduced. Also minimum oil film thickness increases with engine speed but there is a limit. Above this limit, film thickness decreases in opposition because of crankshaft inertia. As increasing of engine torque and oil temperature, munimum oil film thickness decreases linearly. For non-Newtonian oils, the correlation between $100{\circ}C$ kinematic viscosity and munimum oil film thickness is very poor.

• International Journal of Clinical Preventive Dentistry
• /
• v.14 no.4
• /
• pp.247-255
• /
• 2018

Objective: Osseointegration is essential process for successful implants and effects to implant in long term, therefore, passive fitness of good prosthesis is necessary. To make a good prosthesis, at first it should be done a sectioned casting and then joined method of sectioned casting body is recommended. Methods: In this study, to provide the fundamental data on stable connection method for successful implants, the author tested fitness of casting body, and compared difference between gas soldering technique and laser welding technique. Results: In fitness test of 2 abutment (test A, C), gas soldering group's fitness in the opposite part of connection was worse than laser welding group. In fitness test of 3 abutment (test B, D), gap distance was increased both in gas soldering technique and laser welding technique. Gap distance at the connecting part and the opposite part of the abutment in gas soldering technique was worse than laser welding technique and the more additional abutment, the worse gap distance in gas soldering technique. In fitness test of 3 abutment (test B, D), there's little variation in No. 2 abutment when connecting soldering process was done and there's little influence on already soldered connection part when the additional soldering connection was done. Conclusion: On weak loading condition and the part which is needed an accuracy, laser welding technique is more effective and on long-span prosthesis and frequent chewing loading part, laser welding technique is recommended first and applying additional gas soldering technique would be better for making much more successful prosthesis.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.15 no.5
• /
• pp.426-433
• /
• 1990

In this study, we propose a integrated type concentrator and compare with the separated type concentrating method, to accommodate 2B+D ISDN basic access traffic. This system's blocking probabilities are analyzed in terms of each class of bit rate, number of output channels, number of subscriber lines, and offered traffic. The result shows that the proposed method can significantly increase the maximum number of subscriber lines connecting to the system via a T1 carrier, compared with that of the "CCITT proposed" multiplexing scheme or the separated type concentrating method.ng method.

• Proceedings of the SAREK Conference
• /
• 2006.11a
• /
• pp.10-10
• /
• 2006

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.362-364
• /
• 2003

Generally, photovoltaic system is composed a number of solar cells array. so, virtual implementation module for solar cell array is needed Parallel connection each module for extract the power. A desirable characteristic of a parallel supply system is that individual converters share the load current equally and stably. The current sharing(CS) can be implemented using two approaches. The first one, known as a droop method, relies on the high output impedance of each converter. and The second approach, known as active current-sharing techniques. In this paper, analyze for better control logic of parallel connecting virtual implements of solar cell at using droop method.

• Fashion & Textile Research Journal
• /
• v.13 no.5
• /
• pp.661-671
• /
• 2011

This study was designed to produce rounded belt pattern and tight-skirt pattern drafting method using 3D body scan data. Subjects were thirty women in their early twenties. In order to figure out the optimum cutting points, namely, where darts are made, using CAD program, curve ratio inflection points on the horizontal curve of waist, abdomen, and hip to find 1 point in the front, two points in the back part. The average length from center front point to maximum curve ratio was 7.7 cm(46.3%) on the waist curve; 7.9 cm(39.4%) on the abdomen curve. And the average length from center back point to maximum curve ratio point was 6.9 cm(39.0%) for first dart and 11.2 cm(63.3%) for second dart on the waist curve; 8.9 cm(35.8%) for first dart and 15.7 cm(63.3%) for second dart on the hip curve respectively. The cutting lines from were made up by connecting curve inflection points. After divided using cutting lines, each patch was flattened onto the plane and all the technical design factors related with patternmaking were measured, such as dart amount, lifting amount of side waist point, etc. Based on the results of correlation analysis among these factors, regression analysis was done to produce equations to estimate the variables necessary to draw up pattern draft method; F1=F8+1.1, $F4=2.5{\times}F2+0.9$, $F5=0.9{\times}F4+1.0$, $F6=0.3{\times}F4+0.4$, $B1=0.9{\times}B8+2.3$, $B4=2.1{\times}B2+1.3$, $B5=0.9{\times}B4+3.5$, and $B6=0.3{\times}B4+0.4$.