• Journal of Mechanical Science and Technology
• /
• v.19 no.4
• /
• pp.1036-1043
• /
• 2005

Concentric annular heat pipes (CAHP) were fabricated and tested to investigate their thermal characteristics. The CAHPs were 25.4 mm in outer diameter and 200 mm in length. The inner surface of the heat pipes was covered with screen mesh wicks and they were connected by four bridge wicks to provide liquid return path. Three different heat pipes were fabricated to observe the effect of change in diameter ratios between 2.31 and 4.23 while using the same outer tube dimensions. The major concern of this study was the transient response as well as isothermal characteristics of the heat pipe outer surface, considering the application as uniform heating device. A better performance was achieved as the diameter ratio increased. For the thermal load of 180 W, the maximum temperature difference on the outer surface in the axial direction of CAHP was $2.3^{\circ}C$ while that of the copper block of the same outer dimension was $5.9^{\circ}C.$ The minimum thermal resistance of the CAHP was measured to be $0.004^{\circ}C/W.$ In regard to the transient response during start-up, the heat pipe showed almost no time lag to the heat source, while the copper block of the same outer dimensions exhibited about 25 min time lag.

• Wind and Structures
• /
• v.6 no.5
• /
• pp.325-346
• /
• 2003

High-sided road vehicles are susceptible to a sharp-edged crosswind gust, which may cause vehicle accidents such as overturning, excessive sideslip, or exaggerated rotation. This paper thus investigates the dynamic behaviour and possible accidents of high-sided road vehicles entering a sharp-edged crosswind gust with road surface roughness and vehicle suspension included. The high-sided road vehicle is modelled as a combination of several rigid bodies connected by a series of springs and dampers in both vertical and lateral directions. The random roughness of road surface is generated from power spectral density functions for various road conditions. The empirical formulae derived from wind tunnel test results are employed to determine aerodynamic forces and moments acting on the vehicle. After the governing equations of motion are established, an extensive computation work is performed to examine the effects of road surface roughness and vehicle suspension on the dynamic behaviour and vehicle accidents. It is demonstrated that for the high-sided road vehicle and wind forces specified in the computation, the accident vehicle speed of the road vehicle running on the road of average condition is relatively smaller than that running on the road of very good condition for a given crosswind gust. The vehicle suspension system should be taken into consideration, and the accident vehicle speed becomes smaller if the vehicle suspension system has softer springs and lighter dampers.

• Animal cells and systems
• /
• v.13 no.2
• /
• pp.161-167
• /
• 2009

The cuticle of spider's exoskeleton is a hydrophobic and non-adhesive material, but the jumping spiders have the distinctive attachment apparatus for adhesion on smooth dry surface without sticky fluids. We have examined the whole tarsal appendages of the jumping spider, Plexippus setipes with using scanning electron microscope to reveal the fine structural characteristics of the dry adhesion system. All eight legs have the scopulae with a pair of claws on the tip of feet. Each scopula is composed of two groups of setae that are capable of dry adhesion on smooth surface, and the hook structure of the claw is advanced to move on the rough surface. The setae toward the bottom of the tarsal segment are densely covered by numerous setules on the underside which broadened from middle to distal portion. It has been revealed by this research that the contact area of the setule is always a triangular shape, and these cuticular surfaces are connected by the elongated stalks from the underlying setae. It is likely that the nano-scale structures including a triangular depression and a longitudinal groove on each setule could functionate when the spider detach its feet from the substrate.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.24 no.1
• /
• pp.128-137
• /
• 2000

A range of suede-like samples were collected including woven fabric type, nonwoven fabric type, and natural suede(sheep). The surface textures of these suede-like fabrics are rather diverse and different from the plain filament type fabrics since there are a lot of fine surface free fiber ends. Physical and mechanical measurements were carried using the KES equipments. Based on the Kawabata-Niwa translational equation, primary hand values and THV were calculated. Uniaxial tensile tests were performed. Using glossmeter, the reflectance pattern was analyzed at different incidence and receiving angles. In order to capture the surface images of the specimens, a CCD camera and frame grabber connected to a PC were employed. The reflectance uniformity of the images was measured with line-profile analysis and standard deviation values of the profile of the images were calculated. After the multiscale wavelet transfermation, correlation among the transformed image was analyzed at each scale. The reflectance uniformity of the natural suede was better than that of nonwoven type suede, while that of woven type suede was the last among the selected three samples(natural suede, nonwoven type, woven type). The correlation analysis among images has shown the possibility of using the wavelet transformation of the images as one of the measures to detect similarities among the textured specimens.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.874-877
• /
• 2018

Many SMDs (surface mount device) are mounted and mutually connected on a PCB (printed circuit board). System performance degrades when their transmission characteristics are bad. Pads connecting a PCB and SMDs affects PCB transmission characteristics significantly, so pad should be properly aligned to optimize impedance matching. In this paper, effects on PCB transmission characteristics are simulated by pad alignment. When frequency is relatively low, pad alignment seldom affect PCB transmission characteristics, but it affects more and more when frequency or pad size becomes larger. Therefore, pad alignment should be carefully chosen based on target frequency and pad size. Especially, the proposed edge-aligned pad is generally more advantageous over the conventional centered-aligned pad in 12~16 GHz Ku-band frequency.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.9
• /
• pp.1463-1466
• /
• 2007

Single phases of multi-component oxides films, ZrTiO4 and Ta2Zr6O17, could be synthesized by using the combinatorial approach through surface sol-gel route, coating the appropriate mole ratio of 100 mM zirconium butoxide, tantalum butoxide and titanium butoxide precursors on Pt/Ti/SiO2/Si (100) substrate, following pyrolysis at 450 oC, and annealing them at 770 oC. Both the films and bulks of ZrTiO4 and Ta2Zr6O17 showed very stable dielectric properties in temperature range, ?140 to 60 oC, and frequency range, 100 Hz to 1 MHz, promising their applications in wide range of temperatures and frequencies. The dielectric constants of the films were lower and a little more dependent on frequency than those of the bulks. The reduction of dielectric property in the film was mainly due to the interfacial effects that worked as series and parallel-connected capacitances toward the substantial film capacitance.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.4
• /
• pp.56-61
• /
• 2009

This paper presents the ground surface potential profiles and hazard voltages around the metallic structure connected to a small-sized model ground electrode. Because it is very difficult to draw valid conclusions concerning a general grounding problem from actual field data, scale model tests can be used to determine the touch and stop voltages and surface potential profiles around ground electrode. In this work, a hemispherical vessel with a diameter of 1,100[mm] was employed to simulate uniform soil. As a result, the ground surface potential around the ground electrode was significantly raised In particular the ground surface potential at the just upper point of ground rod was higher than other points. When the buried depth of ground rod is increased, the ground surface potential and step voltage were lowered but the touch voltage was elevated.

• Polymer(Korea)
• /
• v.37 no.4
• /
• pp.431-436
• /
• 2013

Polycarbonate (PC) films have been irradiated with various kinds of ions according to energy and dose. Change of the optical transmittance and chemical characteristics were confirmed by UV-VIS and FTIR (ATR) spectroscopy respectively. These UV-A block in 400 nm was variable from 10 to 100% according to energy and doses. Surface electrical resistance of PC film irradiated by ion beam was $10^6-10^{13}{\Omega}/cm^2$, which reveal variation of conduction. Contact angle of film irradiated by ion beam was decreased than the pristine film. Polymer surface morphology was examined by means of atomic force microscopy (AFM). As expected, degradation of polymer film was higher after irradiation with heavier Xe ions but the roughness in the polymer surface morphology were more pronounced for Ar ions. This observed effect can be explained by stronger compaction of polymer surface layer in the case of Xe irradiation, connected with a reduction of free volume available.

• Korean Journal of Plant Taxonomy
• /
• v.42 no.1
• /
• pp.24-39
• /
• 2012

The palynological study of 31 taxa of Korean Artemisia L. was carried out to evaluate their taxonomic characteristics and to determine the relationships among the taxa. The size and shape of the pollen are not used as characteristics to classify the taxa of Korean Artemisia L., but the granule distribution ands pinule connection on the exine were useful for an interspecific classification and for reflecting the relationship between some taxa. It is considered that Artemisia pollen has evolved from a connected spinule and a nearly psilate surface into 1) a connected spinule and a granule surface, 2) a disconnected spinule and a granule surface, 3) a disconnected spinule and a dense granule surface. These pollen characteristics with external morphological characteristics, a geographical distribution and a somatic chromosome number are considered to be good characteristics for distinguishing the relationship of some taxa, such as the A. japonica group (A. hallaisanensis, A. angustissima, A. littoricola) and the A. sacrorum group (A. sacrorum var. sacrorum, A. sacrorum var. incana, A. sacrorum var. iwayomogi).

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.6
• /
• pp.501-510
• /
• 2017

In this study, it is estimated that ceramic membrane process which can operate stably in harsh conditions replacing existing organic membrane connected with coagulation, sedimentation etc.. Jar-test was conducted by using artificial raw water containing kaolin and humic acid. It was observed that coagulant (A-PAC, 10.6%) 4mg/l is the optimal dose. As a results of evaluation of membrane single filtration process (A), coagulation-membrane filtration process (B) and coagulation-sedimentation-membrane filtration process (C), TMP variation is stable regardless of in Flux $2m^3/m^2{\cdot}day$. But in Flux $5m^3/m^2{\cdot}day$, it show change of 1-89.3 kpa by process. TMP of process (B) and (C) is increased 11.8, 0.6 kpa each. But, the (A) showed the greatest change of TMP. When evaluate (A) and (C) in Flux $10m^3/m^2{\cdot}day$, TMP of (A) stopped operation being exceeded 120 kpa in 20 minutes. On the other hand, TMP of (C) is increased only 3 kpa in 120 minutes. Through this, membrane filtration process can be operated stably by using the linkage between the pretreatment process and the ceramic membrane filtration process. Turbidity of treated water remained under 0.1 NTU regardless of flux condition and DOC and $UV_{254}$ showed a removal rate of 65-85%, 95% more each at process connected with pretreatment. Physical cleaning was carried out using water and air of 500kpa to show the recovery of pollutants formed on membrane surface by filtration. In (A) process, TMP has increased rapidly and decreased the recovery by physical cleaning as the flux rises. This means that contamination on membrane surface is irreversible fouling difficult to recover by using physical cleaning. Process (B) and (C) are observed high recovery rate of 60% more in high flux and especially recovery rate of process (B) is the highest at 95.8%. This can be judged that the coagulation flocs in the raw water formed cake layer with irreversible fouling and are favorable to physical cleaning. As a result of estimation, observe that ceramic membrane filtration connected with pretreatment improves efficiency of filtration and recovery rate of physical cleaning. And ceramic membrane which is possible to operate in the higher flux than organic membrane can be reduce the area of water purification facilities and secure a stable quantity of water by connecting the ceramic membrane with pretreatment process.