• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.4
• /
• pp.387-392
• /
• 1997

This paper describes a combination surge generator for carrying out performance tests on the surge protection circuits of shipboard electrical systems. Pspice simulations were performed to decide the values of the parts required and to analyze the characteristics of the generator circuitry. The surge generator fabricated can produce four of the most common surge test waveforms : the O.5i/S/100kHz Ringwave, the 1.2/50$\mu$S voltage, the 8/20$\mu$S current, and the lO/lOOOi/S voltage wave¬forms specified in ANSI Std. C62. Source impedances of the surge generator are 12$\Omega$ in the O.5$\mu$S/100kHz mode, O.5$\Omega$ in the 1.2/50$\mu$S and 8/20$\mu$S mode, and 40$\Omega$in the l0/1000$\mu$S mode, and are determined by the ratio of the maxi¬mum open - circuit voltage to the maximum short - circuit current. Experimental results show that the surge generator provides most of the outputs required for the testing of the surge protection circuits on shipboard electrical systems.

• Journal of Power Electronics
• /
• v.17 no.4
• /
• pp.1088-1096
• /
• 2017

Load variations on a distribution line result in voltage fluctuations at the point of common coupling (PCC). In order to keep the magnitude of the PCC voltage constant at its rated value and obtain zero voltage regulation (ZVR), a D-STATCOM is installed for voltage correction. Moreover, the ZVR mode of a D-STATCOM can also be used to balance the source current during unbalanced loading. For medium voltage and high power applications, a D-STATCOM is realized by the cascaded H-bridge topology. In the ZVR mode, the D-STATCOM may draw unbalanced current and in this process is required to handle different phase powers leading to deviations in the cluster voltages. Zero sequence voltage needs to be injected for ZVR mode, which creates circulating power among the phases of the D-STATCOM. The computed zero sequence voltage and the individual DC capacitor balancing controller help the DC cluster voltage follow the reference voltage. The effectiveness of the control scheme is verified by modeling the system in MATLAB/SIMULINK. The obtained simulations are further validated by the experimental results using a dSPACE DS1106 and five-level D-STATCOM experimental set up.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.485-486
• /
• 2005

Fringe-field switching mode which has a horizontal and vertical electric field exhibits high transmittance and wide viewing angle characteristics. In the FFS mode, a passivation layer between common and pixel electrodes exists, which functions as preventing current leakage of fringe-field. In this paper, we have studied LC behavior, transmittance and operating voltage characteristics with applied voltage as a function of the passivation layer thickness and defined optimal value of the layer to be about $0.5{\mu}m$.

• Journal of Advanced Information Technology and Convergence
• /
• v.8 no.2
• /
• pp.59-67
• /
• 2018

The minimum power supply voltage of a typical bandgap current reference (BGCR) is limited by operating temperature and input common mode range (ICMR) of a feedback amplifier. A new BGCR using a bandgap voltage generator (BGVG) is proposed to minimize the effect of temperature, supply voltage, and process variation. The BGVG is designed with proportional to absolute temperature (PTAT) characteristic, and a feedback amplifier is designed with weak-inversion transistors for low voltage operation. It is verified with a $0.18-{\mu}m$ CMOS process with five corners for MOS transistors and three corners for BJTs. The proposed circuit is superior to other reported current references under temperature variation from $-40^{\circ}C$ to $120^{\circ}C$ and power supply variation from 1.2 V to 1.8 V. The total power consumption is $126{\mu}W$ under the conditions that the power supply voltage is 1.2 V, the output current is $10{\mu}A$, and the operating temperature is $20^{\circ}C$.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.346-347
• /
• 2020

This paper presents the two combination methods for leakage current reduction in photovoltaic system PCS. The leakage current in the photovoltaic system generated from the parasitic capacitance existing between the photovoltaic system and ground relevance to common mode voltage caused by PWM switching. Firstly, Leakage current reduced by a PWM method using two carriers with 180-degree phase different. Secondly, the leakage current is more reduced by connecting LCL filter to the mid-point of DC link. This combining method is revealed in PSIM simulation with 1 uF parasitic capacitance.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.3
• /
• pp.115-124
• /
• 2002

This paper presents an active auxiliary edge-resonant DC link snubber with a ringing surge damper and a three-phase voltage source type zero voltage soft-switching inverter with the resonat snubber treated here for the AC servo motor driver applications. The operation of the active auxiliary edge-resonant DC link snubber circuit with PWM voltage is described, together with the practical design method to select its circuit parameters. The three-phase voltage source type soft-switching inverter with a single edge-resonant DC link snubber treated here is evaluated and discussed for the small-scale permanent magnet (PM) type-AC servo motor driver from an experimental point of view. In addition to these, the AC motor stator current and its motor speed response for the proposed three-phase soft-switching inverter employing Intelligent Power Module(IPM) based on IGBTS are compared with those of the conventional three-phase hard-switching inverter using IPM. The practical effectiveness of the three-phase soft-switching inverter-fed permanent magnet type AC motor speed tracking servo driver is proven on the basis of the common mode current in a novel type three-phase soft-switching inverter-fed AC motor side and the conductive noise on the mains terminal interface voltage as compared with those of the conventional three-phase hard-switching inverter-fed permanent magnet type AC servo motor driver for the speed tracking applications.

• International Journal of Aerospace System Engineering
• /
• v.9 no.1
• /
• pp.1-15
• /
• 2022

Pyrotechnic initiators provide a source of pyrotechnic energy used to initiate a variety of space mechanisms. Pyrotechnic systems build in electromagnetic environment that may lead to critical or catastrophic hazards. Special precautions are need to prevent a pulse large enough to trigger the initiator from appearing in the pyrotechnic firing circuits at any but the desired time. The EMC verification shall be shown by analysis or test that the pyrotechnic systems meets the requirements of inadvertent activation. The MIL-STD-1576 and two range safeties, AFSPC and CSG, require the safety margin for electromagnetic potential hazards to pyrotechnic systems to a level at least 20 dB below the maximum no-fire power of the EED. The PC23 is equivalent to NASA standard initiator and the 1EPWH100 squib is ESA standard initiator. This paper verifies the two safety margins for electromagnetic potential hazards. The first is verified by analyzing against a RF power. The second is verified by testing against a DC current. The EMC safety margin requirement against RF power has been demonstrated through the electric field coupling analysis in differential mode with 21 dB both PC23 and 1EPWH100, and in common mode with 58 dB for PC23 and 48 dB for 1EPWH100 against the maximum no-fire power of the EED. Also, the EMC safety margin requirement against DC current has been demonstrated through the electrical isolation test for the pyrotechnic firing circuits with greater than 20 dB below the maximum no-fire current of the EED.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.190-193
• /
• 2001

ZnO varistors have been widely used to protect power system and electronic system against overvoltages based on their excellent nonlinearity. In order to increase their protection capability, the fracture and protection technologies of arresters have to study according to their applications, namely ImA DC voltage, leakage currents, impulse residual voltages, withstanding capability to impulse surge, and energy absorption capability. ZnO varistors which have nonlinear current-voltage characteristic name a number of failure mechanism when ZnO elements absorb surge energies. Failure mode by thermal stress and Pin hole are among the most common failure mechanism at the high current surge current. In this study, the fracture mechaism of power arresters are introduced and protection technologies are researched. In particular the effect of thermal stress by surge currents to ZnO elements and methods against arc surge energy through withstand structure design of arrester are discussed.

• The Journal of the Korea Contents Association
• /
• v.6 no.3
• /
• pp.38-45
• /
• 2006

A dual-level low voltage differential signalling (DLVDS) circuit is proposed aiming at reducing transmission lines for a LCD driver IC. We apply two data to the proposed DLVDS circuit as inputs. Then, the transmitter converts two inputs to two kinds of fully differential signals. In this circuit, two transmission lines are sufficient to transfer two inputs while keeping the LVDS feature. However, the circuit has a common mode bias fluctuation due to difference of the input bias and the reference bias. We compensate the common mode bias fluctuation using a feedback circuit of the current source bias. The receiver recovers the original input data through a level decoding circuit. We fabricated the proposed circuit using $0.25{\mu}m$ CMOS technology. The simulation results of proposed circuit shows 1-Gbps/2-line data rate and 35mW power consumption at 2.5V supply voltage, respectively.

• Journal of Korean Society of Transportation
• /
• v.29 no.6
• /
• pp.97-106
• /
• 2011

Mode choice model is an essential element for estimating- the demand of new means of transportation in the planning stage as well as in the establishment phase. In general, current demand analysis model developed for the mode choice analysis applies common parameters of utility function in each region which causes inaccuracy in forecasting mode choice behavior. Several critical problems from using common parameters are: a common parameter set can not reflect different distribution of coefficient for travel time and travel cost by different population. Consequently, the resulting model fails to accurately explain policy variables such as travel time and travel cost. In particular, the nonlinear logit model applied to aggregation data is vulnerable to the aggregation error. The purpose of this paper is to consider the regional characteristics by adopting the parameters fitted to each area, so as to reduce prediction errors and enhance accuracy of the resulting mode choice model. In order to estimate parameter of each area, this study used Household Travel Survey Data of Metropolitan Transportation Authority. For the verification of the model, the value of time by marginal rate of substitution is evaluated and statistical test for resulting coefficients is also carried out. In order to crosscheck the applicability and reliability of the model, changes in mode choice are analyzed when Seoul subway line 9 is newly opened and the results are compared with those from the existing model developed without considering the regional characteristics.