• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.1
• /
• pp.157-167
• /
• 2016

Detached residential housing areas are located in the west part of Pangyo City. Seven areas of them are designated for the displaced residents from their original homes by the city development, in which commercial use on the first floor is permitted. The District Plan for the areas were establishes, and one of its main goals is to secure privately owned public spaces (POPS). This research conducted a post enumeration survey on the POPS on the blocks in the seven areas, which blocks contain inner corridors between two rows of housing units. Analytical review of the survey result reveals that (1) POPS facing roads are mainly being used as parking lots or expansion-spaces for the commercial use on the first floor, (2) inner POPS forming corridors are being neglected and otherwise being used as storage areas or outdoor sub-kitchen spaces, and (3) no consideration has been taken for the continuity of the sloped corridors. Regardless of a few good practices in terms of air circulation and lighting, the POPS in the blocks prove to be limited in following the plan's original design intentions and principles.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.26 no.3
• /
• pp.52-64
• /
• 2023

As cities continue to develop rapidly, overcrowding, pollution, and urban sanitation problems arise, and the need to separate conflicting uses is emerging. From this perspective, there is no disagreement that urban land use should be planned. Therefore, all activities in land space must be predicted in advance and planned so that land use can be rationally established. This study used the constructed data to compare and analyze the use distribution characteristics of residential, commercial, and industrial areas in Busan Metropolitan City to identify the building area status, total floor area, and floor area ratio by use zone in districts and counties in Busan Metropolitan City. As a result, it was found that the residential area accounted for the largest proportion of the area by use zone at 51%, and that the residential area accounted for the largest proportion at 63% of the total floor area by use zone. And the analysis was conducted using a specialization coefficient that can identify regional characteristics based on land use composition ratio. Because it is difficult to determine the trend of the entire region just by counting the absolute value of the area, the area composition ratio was calculated and compared. Looking at the residential facilities among the specialization coefficients by use area, it is above 1.0 except for Gijang-gun, Sasang-gu, Saha-gu, and Jung-gu. Commercial facilities are over 1.0 except for Gijang-gun, Gangseo-gu, Nam-gu, Sasang-gu, and Saha-gu. Looking at industrial facilities, you can see that the industrial complex distribution area is Gangseo-gu (2.5), Gijang-gun (1.22), Sasang-gu (2.06), and Saha-gu (1.64). In addition, it was found that business facilities and educational welfare facilities were evenly distributed. Land use analysis was conducted through simulation of the current status of building heights according to each elevation in each use area and the height of buildings in each use area. In general, areas over 80m account for more than 43% of Busan City, showing that the distribution of use areas is designated in areas with high altitude due to the influence of topographical conditions.

• The Korean Journal of Air & Space Law and Policy
• /
• v.23 no.1
• /
• pp.83-109
• /
• 2008

According to 1944 Chicago Convention aircraft are classified into public aircraft(or state aircraft) and private aircraft(or civil aircraft). However even if public aircraft owned by government are used as commercial flights, those are classified into private aircraft. But as far as space activities are concerned in the 1967 Outer Space Treaty, those are related to all activities and all space objects, thus there being no differentiation between the public spacecraft and private spacecraft. As for the institutions of air law there are ICAO, IATA, ECAC, AFCAC, ACAC, LACAC in the world. However in the field of space law there is no International Civil Space Organization like ICAO. There is only COPUOS in the United Nations. The particular institutions such as INTELSAT, INMARSAT, ITU, WIPO, ESA, ARABSAT would be helpful to space law field. In the near future there is a need to establish International Civil Space Organization to cover problems rising from all space activities. According to article 1 of the 1944 Chicago Convention the contracting States recognize that every State has complete and exclusive sovereignty over the airspace above its territory. It means that absolute airspace sovereignty is recognized by not only the treaty law and but also customary law which regulates non-contracting States to the treaty. However as for the space law in the article n of the 1967 Space Treaty outer space, including the moon and other celestial bodies, is not subject to national appropriation by claim of sovereignty, by means of use or occupation, or by any other means. It creates res extra commercium like the legal status of high seas in the law of the sea. However the 1979 Moon Agreement proclaimed Common Heritage of Mankind as far as the legal status of the outer space is concerned which is like the legal status of deep sea-bed in the 1982 United Nations Law of the Sea. As far as the liabilities of air transport system are concerned there are two kinds. One is the liabilities to passenger on board aircraft and the other is the liabilities to the third person or thing on the ground by the aircraft. The former is regulated by the Warsaw System, the latter by the Rome Convention. As for the liabilities of space law the 1972 Liability Convention applies. The Rome Convention and 1972 Liability Convention stipulate absolute liability. In the field of space transportation there would be new liability system to regulate the space passengers on board spacecraft like Warsaw System in the air transportation.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.8 no.3
• /
• pp.53-66
• /
• 2005

The objective of this study is the classification of priority areas for the implementation of green roof by evaluating environmental deterioration in Seoul. Non-permeable pavement, air pollution, habitual floods, energy use, heat island and green space are considered in this assessment indicators. The expert questionnaire survey was conducted in order to determine the most important indicators. These indicators were then, thoroughly evaluated. As a result, high priority areas for the implementation of green roof were deduced in the following order of the districts : Jung, Sungdong, Jungrang, Youngdungpo, Jongro and Kangnam. The highest priority areas were determined to be crowded business-commercial areas. Low priority areas are analyzed in the following order of the districts : Kwanak, Nowon, Seocho and Dobong. The result of this study can be utilized for environmental planning and decision of related policies. Additionally, it can be promoted that awareness of implementing green roof of citizens, policy makers and building owners and effect of green networking between inside and outside Seoul can be increased.

• Korean Journal of Computational Design and Engineering
• /
• v.12 no.1
• /
• pp.39-49
• /
• 2007

Recently three-dimensional (3-D) die design and production process has been widely introduced into the tooling shops of automotive manufacturers to reduce time-to-production of brand-new automobiles. 3-D solid models created in CAD systems are used not only for various simulations for design verification, but also for NC tool path generation to machine dies and their Styrofoam patterns. However, a lot of time and cost will be required to build solid models for dies if designers use only the generalized modeling capabilities of commercial 3-D CAD systems. To solve this problem, it is necessary to customize 3-D CAD system for the specific die design and manufacturing process. This paper describes a dedicated 3-D CAD system based on Unigraphics for die design for automotive body panels. The system provides not only 3-D design capabilities, but also standard part libraries, to enhance design productivity. The design process modeling technology has been introduced to facilitate redesign of the die for the modified panel. By introducing this system, dies can be designed more rapidly in the 3-D space, and their solid data can be directly transferred to CAM tools for NC tool path generation and simulation tools for virtual manufacturing.

• Journal of the Korean Institute of Rural Architecture
• /
• v.20 no.1
• /
• pp.93-101
• /
• 2018

The area to be surveyed is the three-seat of Myeon office in Hwasun-gun, Jeollanam-do, where population is declining. Satisfaction with the use of local residents of rural central areas providing life services in the back area was identified, focusing on sustainable development and the compact cities. Based on the results of the study, the recommendations are as follows. First, the local spaces to be surveyed need a shift to a walk-centered choice and social structure, not a must-oriented, activity-centric structure. This not only improves the neighborhood of rural areas, but also increases the frequency of pedestrian exchange and helps keep the community afloat. Second, it could enhance the convenience of residents by reviving stocks in existing commercial areas and integrating public services. Finally, it has the effect of taking care of the socially disadvantaged and immigrants in terms of space welfare, and securing jobs through locally customized community businesses.

• Tunnel and Underground Space
• /
• v.12 no.1
• /
• pp.1-9
• /
• 2002

Recently, the use of image analysis methods and commercial equipments has been extensively increased in the field of rock engineering. However the problem of errors involved in the image acquisition and subsequent analysis procedure has been frequently neglected. In addition there has been few studies dealing with this problem. So proper color calibration method is needed to be developed for the objectivity and improvement of reliability on image analysis of rock. Color calibration method using standard color rendition chart was adopted on this study. Color calibration and error analysis were carried out for the image acquired from granite rock samples. As a result, comparison among other rock images and improvement of reliability on whole analysis were possible.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.11
• /
• pp.1059-1066
• /
• 2011

The micro-perforated panel absorber(MPPA) is one of promising noise control elements because of its applicability to extreme environments where general porous materials cannot be used. Since the MPPA is inherently non-porous sound absorber, it can be a good candidate of acoustic protection system of a space launcher. The overall sound pressure level inside payload fairings of commercial launch vehicles is so high(around 140 dB OASPL) that the conventional linear impedance model cannot be directly applied to the design of the acoustic protection systems. In this paper an acoustic impedance models of a micro-perforated panel absorber at high sound pressure environment were reviewed and the use of the impedance on the practical design of MPPAs was addressed. The variation of absorption characteristics of MPPA was discussed according to the design parameters, e.g., perforation ratio, the minute hole diameter, the thickness of MPP and the incident sound pressure level.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.2
• /
• pp.1-7
• /
• 2004

This experimental study investigates the wall display of shoes shops among the commercial space to suggest a desirable lighting by focusing on the lighting on the lighting surroundings. The important outcomes of this study are summarized below. The result of the experiment for the wall lighting: For the wall lighting, which needs a diversity, there should be various light source or bigger rate of illuminance between the ambient lighting and the local lighting. There is another possibility that is we can use the lower rate of illuminance with the ambient lighting and the local lighting or higher illuminance generally. The other wall lighting, which need a luminance and a emotional response, will be more effective as they take the lower rate of illuminance with the ambient lighting and the local lighting or higher illuminance generally.

• Journal of Information Technology Services
• /
• v.19 no.3
• /
• pp.139-149
• /
• 2020

There are now many different commercial weather sensors suitable for smart farms, and various smart farm devices are being developed and distributed by companies participating in the government-led smart farm expansion project. However, most do not comply with standard specifications and are therefore limited to use in smart farms. This paper proposed the connecting structure of operating non-standard node devices in smart farms following standard specifications supporting smart greenhouse. This connecting structure was proposed as both a virtual node module method and a virtual node wrapper method. In addition, the SoftFarm2.0 system was experimentally operated to analyze the performance of the implementation of the two methods. SoftFarm2.0 system complies with the standard specifications and supports non-standard smart farm devices. According to the analysis results, both methods do not significantly affect performance in the operation of the smart farm. Therefore, it would be good to select and implement the method suitable for each non-standard smart farm device considering environmental constraints such as power, space, distance of communication between the gateway and the node of the smart farm, and software openness. This will greatly contribute to the spread of smart farms by maximizing deployment cost savings.