• Journal of Powder Materials
• /
• v.10 no.1
• /
• pp.15-20
• /
• 2003

Hybrid $A1_2O_3-TiC$ ceramic particle reinforced 6061 and 5083 Al composite powders were prepared by the combination of twin rolling and stone mill crushing process, followed by consolidating processes of cold compaction, degassing and hot extrusion. The composite bar consists of lamellar structure of ceramic particle rich area and matrix area, in which the hybrid was decomposed into each TiC of about $3-4\mutextrm{m}$ and $AI_2O_3$ particles of about $1-2\mutextrm{m}$ in diameter. It also found that fine $Mg_2Si$ precipitates of about 30 nm were embedded in the matrix, which have grains of about 3 $\mutextrm{m}$. Higher UTS was measured at the 5083 composite bar compared to the conventionally fabricated composite, due to again refinement effect by the rapid solidification. No particle was shown to form in the interface between the matrix and reinforcement, whereas carbon was diffused into the matrix.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.03a
• /
• pp.144-147
• /
• 1998

VCR is a back-up roll with a special contour which leads to the length of the contact line between back-up roll and work becones self adjustable in accordance with the width of the strip. The simulation of a finite element model and the on-line test at production mill demonstrate that the VCR roll may keep the crown of the roll gap relatively stable, and at same time, permit the rolling pressure to be adjusted over a wider range, and increase the effect of work roll bending on the roll gap. The VCR rolls have been successfully used at the first stands of two largest cold rolling mills in China, and on-line test has been done at a wide hot strip finishing train. The use of VCR roll has created favorable conditions for subsequent rolling passes and the achievement of better flatness quality.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.197-203
• /
• 2004

A full finite element (FE)-based approach is presented for the precision analysis of the strip profile in flat rolling. Basic FE models for the analysis of the mechanical behavior of the strip and of the rolls are described in detail. Also described is an iterative strategy for a rigorous treatment of the mechanical contact occurring at the roll-strip interface and at the roll-roll interface. Then, presented is an integrated FE process model for the coupled analysis of the mechanical behavior of the strip, work roll, and backup roll in four-high mill. A series of process simulation are conducted and the results are compared with the measurements made in hot and cold rolling experiments.

• Korean Journal of Materials Research
• /
• v.26 no.3
• /
• pp.154-159
• /
• 2016

A roll-bonding process was applied to fabricate an AA1050/AZ91/AA1050 laminate complex sheet. Two AA1050 and one AZ91 magnesium sheets of 2 mm thickness, 30 mm width and 200 mm length were stacked up after surface treatment that included degreasing and wire brushing; material was then reduced to a thickness of 3 mm by one-pass cold rolling. The laminate sheet bonded by the rolling was further reduced to 2 mm in thickness by conventional rolling. The rolling was performed at 623K without lubricant using a 2-high mill with a roll diameter of 210 mm. The rolling speed was 15.9 m/min. The AA1050/AZ91/AA1050 laminate complex sheet fabricated by roll bonding was then annealed at 373~573K for 0.5h. The microstructure of the complex sheets was revealed by electron back scatter diffraction (EBSD) measurement; the mechanical properties were investigated by tensile testing and hardness testing. The strength of the complex sheet was found to increase by 11 % and the tensile elongation decreased by 7%, compared to those values of the starting material. In addition, the hardness of the AZ91 Mg region was slightly higher than those of the AA1050 regions. Both AA1050 and AZ91 showed a typical deformation structure in which the grains were elongated in the rolling direction; however, the mis-orientation distribution of grain boundaries varied greatly between the two materials.

• Applied Chemistry for Engineering
• /
• v.20 no.3
• /
• pp.301-306
• /
• 2009

This research was carried out to establish the effective treatment condition and characteristic of wastewater from the electroplating plant of cold rolling mill by using microorganism. Alkaline wastewater and acidic heavy metal wastewater accounted for 64%, 30%, respectively, of the total wastewater. Highly concentrated thiocyanate was 53890 mg/L as COD and it was 53% of total COD, even though it was 0.03% of wastewater from the electroplating plant. When treating mixed wastewater with microorganism, it was easy to remove when SCN concentrations of mixed wastewater was 200 mg/L or less. While the treatment effect of COD-causing materials was low at the concentration of 400 mg/L or less, it implies that highly concentrated thiocyanate contains a large amount of slowly biodegradable organics. When treating with mixed wastewater, pH was 7.33 at the beginning, but after 8 hours it increased to 7.99. This is caused by ammonia which is generated when SCN of highly concentrated thiocyanate was degraded by microorganism.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2230-2234
• /
• 2003

This paper proposes a distributed simulator for general control system in CEMTool. Systems can be described by SIMTool likes the simulink in Matlab. For distributed simulation, we can seperate any system into several parallel subsystems in SIMTool. The number of parallel subsystem can be determined by the system's property. After seperation, parallel simulator will do initialization, one-step-ahead simulation, block-distribution and ordering and so on. Finally, simulator will create independent C codes and executive files for each subsystem. The whole system is fulfilled by several PCs, and each PC executes one subsystem. There are communications among these subsystem using reflective memory or ethernet. We have made several experiments, and the 5-stand cold rolling mill control system is our main target. The result of parallel simulation has shown effective speedup in comparison with one pc simulation.

• Resources Recycling
• /
• v.11 no.5
• /
• pp.24-29
• /
• 2002

In this study, to improve the color of iron oxide from waste pickling acid at the cold rolling mill, the quality control technologies especially about color were investigated on the spray roaster and iron oxide powder. At the operation condition of the spray roaster, the charge amount of waste acid per hour, temperature, numbers of spray nozzle were investigated. At admixing process, titanium oxide, silica, goethite were tested. Color character of iron oxide can be improved by process control at spray roaster and by admixing process at a pigment factory Iron oxide from results of this study is enough to use as the colorant of concrete product.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.350-354
• /
• 1995

The Tension Leveller of Cold Rolling Mill In POSCO performs levelling the strip in high speed line. But minor variations in operating condition of driving machines such as motor, gear box, and support bearings, a small gap-variation of supporter and strip slip by poor roll revolutions can cause serious problems in the quality of strip. In this study, firstly, A condition monitoring standard for each sensor is made through with the detail analysis of vibration and strip slip. Secondly, An automatic monitoring and diagnosing system was developed to monitor the condition of Tension Leveller, and diagnose the cause of abnormal condition. Finally, A diagnosing algorithm for abnormal condition and man-machine interface (MMI) for easy operation are developed.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.179.6-179
• /
• 2001

This paper proposes the recognition method of the strip shape using the Least-Square method and the distinction method of the asymmetric shape and the compensation method upon the shape control values for the stainless steel cold rolling mill. This paper proposes the shape recognition method before control and the compensation method to minimize the fluctuation of the shape deviation and to get symmetric shape. This paper shows on line test results to verify the performance of the control method for the process. The experiments have been performed with respect to various material type, thickness, and strip width. The performance of the proposed method is obtained excellent quality and high productivity as results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.5
• /
• pp.373-384
• /
• 2002

This paper presents a robust PID controller design technique using the concept of model matching method in the frequency domain. To design the robust PID controller satisfying disturbance attenuation and robust tracking property for a reference input, first an H$\infty$ controller satisfying given performance is designed using the H$\infty$ control method. And then, the parameters(proportional, integral, and derivative gains) of the robust PID controller are determined using the model matching at frequency domain. The proposed technique is applied to a position controller design of the web. The simulation results show that the proposed robust PID controller satisfies disturbance attenuation and tracking property.