• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.4
• /
• pp.342-349
• /
• 2009

This study investigated the growth characteristics of carbon nanotubes (CNTs) by changing a period of annealing time and a $C_{2}H_{2}/H_2$ flow ratio at temperature as low as $450^{\circ}C$ with inductively coupled plasma chemical vapor deposition. The 1-nm-thick Fe-Ni-Co alloy thin film served as a catalyst layer for the growth of CNTs, which was thermally evaporated on the 15-nm-thick Al underlayer deposited on the 50-nm-thick Ti diffusion barrier. The annealing at low temperature of $450^{\circ}C$ brought about almost no granulation of the catalyst layer, and the CNT growth was not affected by a period of annealing time. A study of changing the flow rate of $C_{2}H_{2}$ and $H_2$ showed that as the ratio of the $C_{2}H_{2}$ flow rate to the $H_2$ flow rate was lowered, the CNTs were grown to be longer With further decreasing the flow ratio, the length of CNTs reached the maximum and then became shorter. Under the optimized gas flow rates, we successfully synthesized CNTs with a uniform length over a 4-inch Si wafer at $450^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.2
• /
• pp.98-103
• /
• 2013

The alumina substrates that Ni electrode was printed on and the multi-layered PTCR thermistors of which composition is $(Ba_{0.998}Ce_{0.002})TiO_3+0.001MnCO_3+0.05BN$ were fabricated by a thick film process, and the effect of re-oxidation temperature on their resistivities and resistance jumps were investigated, respectively. Ni electroded alumina substrate and the multi-layered PTC thermistor were sintered at $1150^{\circ}C$ for 2 h under $PO_2=10^{-6}$ Pa and then re-oxidized at $600{\sim}850^{\circ}C$ for 20 min. With increasing the re-oxidation temperature, the room temperature resistivity increased and the resistance jump ($LogR_{290}/R_{25}$) decreased, which seems to be related to the oxidation of Ni electrode. The small sized chip PTC thermistor such as 2012 and 3216 exhibits a nonlinear and rectifying behavior in I-V curve but the large sized chip PTC thermistor such as 4532 and 6532 shows a linear and ohmic behavior. Also, the small sized chip PTC thermistor such as 2012 and 3216 is more dependent on the re-oxidation temperature and easy to be oxidized in comparison with the large sized chip PTC thermistor such as 4532 and 6532. So, the re-oxidation conditions of chip PTC thermistor may be determined by considering the chip size.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.3 no.1
• /
• pp.18-23
• /
• 1966

An experimental study of a steel plate thickness gauge by means of the measurements of backscatered gamma-rays has been carried out. The difference between this and other methods is that this method does not include any shilding matterials in the detecting probe, because the primary radiations and the backscattered radiations are detected simultaneously by an NaI (TI) scintillating crystal, and the activity of the Co-60 source used is low enough. In this thickness gauge, the thickness of the steel plates can be read directly on the counting ratemeter scale. The optimum conditions in the source-to-detector distance, window width of the analyzer, energy and strength of the gamma-ray source were found experimentally. The results have shown that the accuracy of the gauge was about $\pm$3% in the range of 3 to 8mm thickness. This gauge can be used to detect the pits or corrosions on the inner walls of the steel pipes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.144-144
• /
• 1999

최근 국내 반도체 기술의 비약적인 발전으로 전자 기기 전반에 소형화, 고주파화, 고기능화 등이 진행되는데 반해, 반도체 소자등에 전원을 공급하거나 회로 전체를 운용하는 전기 신호를 변조.증폭시키는데 반해, 반도체 소자등에 전원을 공급하거나 회로 전체를 운용하는 전기신호를 변조.증폭시키는 인덕터, 트랜스 포머와 같은 수동 자기 소자는 아직도 3차원 벌크 형태로 사용되고 있다. 일본을 중심으로 각국에서는 자기 소자의 박막.소형화에 대한 다각도의 연구가 진행되었으나 국내서는 아직 미미한 실정이다. 따라서 고집적 전원 공급 장치나 지능 센서 등에 반도체와 자기 소자의 사용 주파수 대역과 크기가 통합된 반도체-자성체 IC(semiconductor-magnetic integrated circuit)의 필요성이 절실히 요구되고 있다. 현재 사용중인 벌크형 인덕터나, 트랜스 포머의 경우 10NHz이상의 고주파 대역에는 응용되지 못하고 있다. 이는 적용된 자성체가 페라이트(ferrite)로서 초투자율은 크지만 고주파대역에서의 공진 현상에 의해 저투자율을 나타내고, 포화 자속밀도가 낮기 때문이다. 이러한 페라이트 자성체의 대체품으로 주목받고 있는 것이 Fe, Co계 고비저항 자성마이다. 그러나 Co는 낮은 포화자속밀도를 나타내기 때문에 이러한 조건을 충족시키는 자성막으로 Fe계 미세 결정막을 사용하였다. 본 연구에서는 선택적 전기 도금법(selective electroplating method)과 LIGA like process를 이용하여 공시형 인덕터(air core inductor)의 라이브러리(library)를 구축한 뒤, 고주파 대역에서의 우수한 연자기 특성을 가지는 Ti/FeTaN막을 적용한 자기 박막 인덕터(magnetic thin film inductor)를 제작하여 비교.분석하였다. 제조된 인덕터의 특성 추정은 impedence analyzer를 이용하여 주파수에 따른 저항(resistance), 인덕턴스(inductance)를 측정, 계산한 성능지수(quality factor)로서 인덕터의 성능을 평가하였다. 제조된 박막 인덕터의 코일 형상은 5턴의 double rectangular spiral 구조였으며, 적용된 자성막의 유효 투자율9effective permeability)은 1500, 자성막, 절연막 그리고 코일의 두께는 각각 2$\mu\textrm{m}$, 1$\mu\textrm{m}$, 20$\mu\textrm{m}$이며 코일의 폭은 100$\mu\textrm{m}$, 코일간의 간격은 100$\mu\textrm{m}$였다. 제조된 박막 인덕터는 5MHz에서 1.0$\mu$H의 인덕턴스를 나타내었으며 dc current dervability는 100mA까지 유지되었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.10
• /
• pp.601-607
• /
• 2016

Piezoelectric thick films of soft $Pb(Zr,Ti)O_3$ (PZT) based commercial material (S55) were fabricated using a conventional tape casting method. Ag-Pd electrodes were printed on the piezoelectric film at room temperature and all 5 layered films with a dimension of $12mm{\times}16mm$ were successfully laminated for a multi-layered piezoelectric ceramic actuator. The laminated specimens were co-fired at $1,100^{\circ}C$ for 1 h. A flat layered and dense microstructure was obtained for the $112{\mu}m$ thick piezoelectric actuator after sintering process. Thereafter, a prototype piezoelectric speaker was fabricated using the multi-layered piezoelectric ceramic actuator which can operate as a bimorph. Its SPL (sound pressure level) characteristic was also evaluated for speaker application. Frequency response revealed that the output SPL with a root mean square voltage of 10 V increased gradually to the highest peak of 87.5 dB for 1.5 kHz and exhibited a relatively stable behavior over the measured frequency range (${\leq}20kHz$) at a distance of 10 cm, implying that the fabricated piezoelectric speaker is potential for speaker applications.

• Journal of Korean Society for Atmospheric Environment
• /
• v.28 no.1
• /
• pp.39-51
• /
• 2012

Aerosol slurry samples were collected in 60-min interval using Korean Semi-continuous Elements in Aerosol Sampler (KSEAS) between May 19 and June 6, 2010 at an urban site of Gwangju. The $PM_{2.5}$ samples were collected with a flow rate of 16.7 L/min and particles are grown by condensation of water vapor in a condenser maintained at ${\sim}5^{\circ}C$ after saturation by direct injection of steam. The resulting droplets are collected in a liquid slurry with a airdroplet separator. Concentrations of 16 elements (Al, Fe, Mn, Ca, K, Cu, Zn, Pb, Cd, Cr, Ti, V, Ni, Co, As, Se) in the collected slurry samples were determined off-line by ICP-MS. KSEAS sample analysis encompassed the sampling periods for which 24-hr average elemental species concentrations were calculated for comparison with those derived from 24-hr integrated filter samples. Relationship between elemental species measured by two methods indicated high correlation coefficients (r), mostly greater than r of 0.80. However, we note that concentrations of Al, K, Ca, Mn, and Fe, which are often associated with crustal elemental particles, in the KSEAS samples, were substantially lower (1.4~11 times) than those found in the typical filter-based samples. This discrepancy is probably due to difficulties in transferring insoluble dust particles to the collection vials in the KSEAS. Temporal profiles of elemental concentrations indicate that some transient events in their concentrations are observed over the sampling periods. For the elemental species studied, atmospheric concentrations during the transient events increased by factors of 4 in Mn~80 in Zn, compared to their background levels. Principle component analyses were applied to the hourly KSEAS data sets to identify sources affecting the concentrations of the metal constituents observed. In this study, we conclude that hourly measurements for particle-bound elemental constituents were extremely useful for revealing the short-term variability in their concentrations and developing insights into their sources.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2A
• /
• pp.147-156
• /
• 2004

This paper presents an implementation and performance analysis of an access channel decoder which exploits a diversity gain due to the independent magnitude of received signals energy at each of antenna elements of a smart antenna BTS (Base-station Transceiver Subsystem) operating in CDMA2000 1X signal environment. Proposed access channel decoder consists of a searcher supporting 4 fingers, Walsh demodulator, and demodulator controller. They have been implemented with 5 of 1 million-gate FPGA's (Field Programmable Gate Array) Altera's APEX EP20K1000EBC652 and TMS320C6203 DSP (digital signal processing). The objective of the proposed access channel decoders is to enhance the data retrieval at co]1-site during the access period, for which the optimal weight vector of the smart antenna BTS is not available. Through experimental tests, we confirmed that the proposed access channel decoder exploitng the diversity technique outperforms the conventional one, which is based on a single antenna channel, in terms of detection probability of access probe, access channel failure probability, and $E_{b/}$ $N_{o}$ in Walsh demodulator.r.r.

• Journal of Environmental Science International
• /
• v.26 no.1
• /
• pp.67-78
• /
• 2017

Combustion of ethanol (EtOH) at low temperatures has been studied using titania- and silica-supported platinum nanocrystallites with different sizes in a wide range of 1~25 nm, to see if EtOH can be used as a clean, alternative fuel, i.e., one that does not emit sulfur oxides, fine particulates and nitrogen oxides, and if the combustion flue gas can be used for directly heating the interior of greenhouses. The results of $H_2-N_2O$ titration on the supported Pt catalysts with no calcination indicate a metal dispersion of $0.97{\pm}0.1$, corresponding to ca. 1.2 nm, while the calcination of 0.65% $Pt/SiO_2$ at 600 and $900^{\circ}C$ gives the respective sizes of 13.7 and 24.6 nm when using X-ray diffraction technique, as expected. A comparison of EtOH combustion using $Pt/TiO_2$ and $Pt/SiO_2$ catalysts with the same metal content, dispersion and nanoparticle size discloses that the former is better at all temperatures up to $200^{\circ}C$, suggesting that some acid sites can play a role for the combustion. There is a noticeable difference in the combustion characteristics of EtOH at $80{\sim}200^{\circ}C$ between samples of 0.65% $Pt/SiO_2$ consisting of different metal particle sizes; the catalyst with larger platinum nanoparticles shows higher intrinsic activity. Besides the formation of $CO_2$, low-temperature combustion of EtOH can lead to many other pathways that generate undesired byproducts, such as formaldehyde, acetaldehyde, acetic acid, diethyl ether, and ethylene, depending strongly on the catalyst and reaction conditions. A 0.65% $Pt/SiO_2$ catalyst with a Pt crystallite size of 24.6 nm shows stable performances in EtOH combustion at $120^{\circ}C$ even for 12 h, regardless of the space velocity allowed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.285-285
• /
• 2010

Zinc oxide (ZnO) is a direct band gap semiconductor with 3.37 eV, which has in a hexagonal wurtzite structure. ZnO is a good candidate for a photocatalyst because it has physical and chemical stability, high oxidative properties, and absorbs of ultraviolet light. During ZnO is irradiated by UV light, redox (reduction and oxidation) reactions will occur on the ZnO surface, generating the radicals O2- and OH. These two powerful oxidizing agents have been proven to be effective in decomposition of harmful organic materials, converting them into CO2 and H2O. Therefore, we assume that oxygen on the surface of ZnO is a very important factor in the photocatalytic activities of ZnO nanoparticles. Recently, ZnO nanoparticles are studied in various application fields by many researchers. Photocatalyst research is progressing much in various application fields. But the ZnO nanoparticles have disadvantage that is unstable in water in comparison titanium dioxide (TiO2). The Zn(OH)2 was formed at the ZnO surface and ZnO become inactive as a photocatalyst when ZnO is present in the solution. Therefore, we prepared synthesized ZnO nanoaprticles that were immersed in the water and dried in the oven. After that, we measured photocatalytic activities of prepared samples and find the cause of their phtocatalytic activity changes. The characterization of ZnO nanoparticles were analyzed by Scanning Electron Microscopy (SEM), X-ray diffraction (XRD) and BET test. Also we defined the photocatalytic activity of ZnO nanoparticles using UV-VIS Spectroscopy. And we explained changing of photocatalytic activity after the water treatment using X-ray Photoelectron Spectroscopy (XPS).

• Journal of Sericultural and Entomological Science
• /
• v.13 no.1
• /
• pp.69-72
• /
• 1971

1. To study proper sample size in boiling-of test, we extracted samples in size of 200, 100, 50, 20, and 10 grams and tested them. In the result of this test we couldn't find a statistical significance among them, but it is seemed that the proper sample size is 100 gram to think about the errors of measurement and treatment when the sample size is either too little or too much in ordinary test. 2. We tested boil-of result by twisted sample skein (sizing skein) and untwisted sample. In this test to use sodium carbonate (Na$_2$CO$_3$) having powerful sericin dissolving power as a scouring agent, boil-off percents made no statistical significance between two kinds of sample skein. And to use marseilles soap having less powerful sericin dissolving power as a scouring agent, boil-off percents made a difference between twisted and untwisted sample skein. 3. We compared five kinds of scouring agent, for example sodium carbonate, monogen, synthetic detergent (HiTi), marseilles soap A (made in Japan) and marseilles soap B (made in Korea). Among them synthetic detergent and marseilles soap B showed no statistical significance compared with marseilles soap A which we used in ordinary boil-off test. So synthetic detergent and marseilles soap B can be substituted for marseilles soap A. 4. Generally the higher pH value of boil of solution, tile more sericin dissolution, showed and vice versa.