• Journal of IKEEE
• /
• v.17 no.4
• /
• pp.544-549
• /
• 2013

This paper describes a modified binary phase detector (Bang-Bang phase detector - BBPD) for jitter reduction in clock and data recovery (CDR) circuits. The proposed PD reduces ripples in the VCO control voltage resulting in reduced jitter for CDR circuits. A 2.5 Gbps CDR circuit with a proposed BBPD has been designed and verified using Dongbu $0.13{\mu}m$ CMOS technology. Simulation shows the CDR with proposed PD recovers data with peak-to-peak jitter of 10.96ps, rms jitter of 0.86ps, and consumes 16.9mW.

• Transactions on Semiconductor Engineering
• /
• v.2 no.3
• /
• pp.1-5
• /
• 2024

This paper presents a crystal-less reference clock recovery (CR) frequency synthesizer with compensation designed for Bluetooth Low Energy (BLE) Smart-tag applications, operating at frequencies of 32, 72, and 80MHz. In contrast to conventional frequency synthesizers, the proposed design eliminates the need for external components. Using a single-ended antenna to receive a minimal input power of -36dBm at a 2.4GHz signal, the CR synthesizes frequencies by processing the RF signal received through a Low Noise Amplifier ( L N A ) . This approach allows the system to generate a reference clock without relying on a crystal. The received signal is amplified by the LNA and then input to a 16-bit ACC (Automatic Clock Compensation) circuit. The ACC compares the frequency of the received signal with the oscillator output signal, using the synthesis of a 32MHz reference clock through a frequency compensation method. The oscillator is constructed using a Ring Oscillator (RO) with a Frequency Divider, offering three different frequencies (32/72/80MHz) for various system components. The proposed frequency synthesizer is implemented using a 55-nm CMOS process.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.2
• /
• pp.1-6
• /
• 2011

This paper describes a phase modulation I/O (PMIO) serial interface circuit that supports 1Gbps transfer rate with 12mW power consumption at 1.2V supply. The proposed PMIO which consists of TX and RX blocks utilizes a phase modulation technique. The rising edge is fixed to get the clock phase information and falling edge has multi positions for the multi-data information to increase the transfer rate. The designed circuit use the 16 possible falling edge positions. The data transfer rate is four times faster than the clock rate. The circuit has been implemented using $0.13{\mu}m$ CMOS process. Measured results show the circuit exhibits peak-to-peak jitters of transfer data (phase data) and recovery data.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.2
• /
• pp.39-45
• /
• 2004

This paper describes the design and implementation of Serial ATA physical layer and performance measurement. It is composed of tranceiver circuit that has the NRZ data stream with +/-250㎷ voltage level and 1.5Gbps data rate, transmission PLL circuit, clock ＆ data recovery circuit, serializer/deserializer circuit and OOB(Out Of Band) generation/detection circuit. We implement the verification of the silicon chip with 0.18${\mu}{\textrm}{m}$ Standard CMOS process. It can be seen that all of the blocks operate with no errors but the data transfer rate is limited to the 1.28Gbps even this should support 1.5Gbps data transfer rate.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.1
• /
• pp.1-10
• /
• 2010

This paper proposes a two-phase clocked adiabatic static CMOS logic (2PASCL) circuit that utilizes the principles of adiabatic switching and energy recovery. The low-power 2PASCL circuit uses two complementary split-level sinusoidal power supply clocks whose height is equal to $V_{dd}$. It can be directly derived from static CMOS circuits. By removing the diode from the charging path, higher output amplitude is achieved and the power consumption of the diode is eliminated. 2PASCL has switching activity that is lower than dynamic logic. We also design and simulate NOT, NAND, NOR, and XOR logic gates on the basis of the 2PASCL topology. From the simulation results, we find that 2PASCL 4-inverter chain logic can save up to 79% of dissipated energy as compared to that with a static CMOS logic at transition frequencies of 1 to 100 MHz. The results indicate that 2PASCL technology can be advantageously applied to low power digital devices operated at low frequencies, such as radio-frequency identifications (RFIDs), smart cards, and sensors.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.149-152
• /
• 1998

A synchronization is very important element not only wire communication but also wireless communication. A synchronous oscillator(SO) is a network which synchronizes, tracks, filter, amplifies and divides (if necessary) in a single process. The coherent phase synchronous oscillator(CPSO) is created by adding two external loops to the SO. The CPSO ratains all virtues of a SO while providing coherency throughout the tracking range. This paper has applied a clock recovery of GPS signal using CPSO.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.1
• /
• pp.10-14
• /
• 1987

Considering transition gating of the input unipolar NRZ signal, the equivalent linear time-invariant model has been derived for the PLL in the timing clock recovery circuits. The magnitude of the alignment and accumulated jitter has been found along a chain of repeaters. For the timing recovery circuit of 90 Mbps optical communication system, the computer simulation shows that, for the first stage of the chain, the alignment jiter and the accumulated jitter are of -5.1766 dB and for the 7-th stage, the alignment jitter and accumulated jitter have the value of -1.0193dB, 4.9053 dB respectively.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.3
• /
• pp.376-380
• /
• 1987

The closed-loop transfer function of 2-nd order PLL (phase-looked loop)of which loop filter has active-lag 1-st order is found. Considering the three criteria of system performance: the transient response time of the circuit, noise bandwidth by the linear analysis and stability which uses root-locus method, the optimum value of damping factor is 1.0 and the natural frequency which depends upon the signal frequency can be determined after consideration of the trade-off relationship between the transient response time and the noise bandwidth.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.11
• /
• pp.83-91
• /
• 1990

VOC(coltage controlled oscillator) circuits are necessary in applications such at the demodul-ation of FM signals, frequency synthesizer, and for clock recovery from digital data. In this paper, we designed the VCO circuit based on a OTA(operational transconductance amplifier) and the OP amp which using a differential amplifier by BiCMOS circuit. It consists of a OTA, voltage contorolled integrator and a schmitt trigger. Conventional VCO circuits are designed using the CMOS circuit, but in this paper we designed newly BiCMOS VCO circuit which has a good drive avlity, As a result of SPICE simulation, output frequency is 141KHz at 105KHz, and sensitivity is 15KHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.5 s.335
• /
• pp.31-38
• /
• 2005

The architecture and the implementation details of a UTMI(USB2.0 Transceiver Macrocell Interface) compatible USB2.0 transceiver chip were presented. To confirm the validation of the incoming data in noisy channel environment, a squelch state detector and a current mode Schmitt-trigger circuit were proposed. A current mode output driver to transmit 480Mbps data on the USB cable was designed and an on-die termination(ODT) which is controlled by a replica bias circuit was presented. In the USB system using plesiochronous clocking, to compensate for the frequency difference between a transmitter and a receiver, a synchronizer using clock data recovery circuit and FIFO was designed. The USB cable was modeled as the lossy transmission line model(W model) for circuit simulation by using a network analyzer measurements. The USB2.0 PHY chip was implemented by using 0.25um CMOS process and test results were presented. The core area excluding the IO pads was $0.91{\times}1.82mm^2$. The power consumptions at the supply voltage of 2.5V were 245mW and 150mW for high-speed and full-speed operations, respectively.