• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.113-118
• /
• 1989

By using the single mode optical fiber, we fabricated Fiber-optic Fabry-Perot interferometer (FFPI). The change over a wide range in the optical path length of a FFPI is observed. The temporal movement of the interference fringes by external condition to P.Z. T) is converted to circular motion on an oscilloscope display and then recorded with a micro-computer. The two output voltages of the D/A converters are applied to X and Y terminals of oscilloscope to display circular motion on oscilloscope. Thus the direction of phase shift can be determined with observing the direction of circular motion. The variation of the optical length can be measured by calculating the angle of spot of circle with an accuracy of λ/90 wave length due to variation of temperature in this system 2.7x10-4$^{\circ}C$.

• Journal of ILASS-Korea
• /
• v.19 no.2
• /
• pp.69-74
• /
• 2014

The comparison of the flow characteristics between circular and swirl jets which were controlled by the spinner attachment inside the airtube were conducted in this study. Swirl jet means a flow in whirls by mixing the flow of axial and tangential direction. Swirl flow has been used for the improvement of the combustion efficiency in the combustor. This flow is controlled by the spinner which has several vanes inclined by certain angles to the axial direction. In this study, angle of vane $30^{\circ}$ and diameter ratio of outlet to inlet of the airtube 0.73 were made. These spec. should find on the general gun type burner built in the domestic small size boiler. As the flow characteristics, axial and tangential velocities were measured by using the 2-D hot-wire velocimeter system and analyzed statistically. And also this research conducted a practical experiment considering to the attached belongings likes as ignitor, nozzle etc. on the airtube of the gun type burner. As a result, swirl occurred at the occasion of beingness and flow region extended considerably toward the radial direction. But effect of swirl did not transmit to the downstream. And the complicated flow was appeared regardless of the existence of spinner because of the effect of belongings.

• Journal of the Korea Society of Computer and Information
• /
• v.6 no.1
• /
• pp.51-59
• /
• 2001

In this paper, performance of the double circular array antenna was analyzed, which has sharp directivity with specific direction and is compatible to shape pencil beam. The character of each array geometry which N numbers of isotropic point source is arranged in planar with type of a square, circular and double circular was compared and analyzed. As a result, we fined that double circular geometry was good performance rather than square and circular array geometry in the point of directivity. SLL and HPBW.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.4 no.3
• /
• pp.58-66
• /
• 1995

It is very important to test motion accuracy and performance of NC machine tools as they affect that of all other machines machined by them in industry. In this paper, in has become possible to detect errors of linear displacement of radial direction for circular motion test using newly assembled magnetic type of linear scales so called Magnescale ball bar system, and to calculate time interval getting error motion data and revolution angle of circular motion in machining center using tick pulses come out from computer. And a set of error data gotten from test is expressed to a plot by computer treatment and to numerics of error motion by statistical treatment and results of test are compared with those of Renishaw ball bar system.

• Journal of Ocean Engineering and Technology
• /
• v.4 no.1
• /
• pp.110-119
• /
• 1990

This study is concerned about the stress concentration factor measurement by photoelastic method, for the case of two circular holes arrangement in 3mm semi-infinite plate under tensile load, the ratio of those two circular holes diameter, the ratio of distance apart from circular holes to breadth and the two holes arrangement angle with loading direction were varied. Besides, the measured stress concentration by photoelastic method around one circular hole was compared with that by strain-gage method.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.6
• /
• pp.30-37
• /
• 1997

We present an efficient technique, bidirectioanl inertial maximum cost search technique, for th edetection and segmentation of circular shaped objects using the spatial information around the neighborhood of the boundary candidates. This technique searches boundary candidates using local pixdl information such as pixel value and its direction. And then to exclude pseudo-boundary caused by shadows or noises, the local contrast is defined between the clique of the boundary candidates and the cliques of the background. In order to effectively segment circular shaped boundary, the technique also uses the curvature based on trigonometirc function which determines circular shaped boundary segments. Since the proposed technique is applied to the pixel cliques instead of a pixel itself, it is proposed method can easily find out circular boundaries form iamges of the PCB containing circular shaped parts and the trees with round fruits compared to boundary detection by using the pixel information and the laplacian curvature.

• Steel and Composite Structures
• /
• v.17 no.4
• /
• pp.535-548
• /
• 2014

In this paper, the exact closed-form solutions for torsional analysis of heterogeneous magnetostrictive circular cylinder are derived. The cylinder is subjected to the action of a magnetic field produced by a constant longitudinal current density. It is also acted upon by a particular kind of shearing stress at its upper base. The rigidity of the cylinder is graded through its axial direction from one material at the lower base to another material at the upper base. The distributions of circumferential displacement and shear stresses are presented through the radial and axial directions of the cylinder. The influence of the magnetostrictive parameter is discussed. The effects of additional parameters are investigated.

• Journal of computational fluids engineering
• /
• v.18 no.4
• /
• pp.17-24
• /
• 2013

In this study, we consider the characteristics of channel flow in the presence of an infinite streamwise array of equispaced identical rotating circular cylinders. This flow configuration can be regarded as a model representing a micro channel or an internal heat exchanger with cylindrical vortex generators. A numerical parametric study has been carried out by varying Reynolds number based on the bulk mean velocity and the cylinder diameter, and the gap between the cylinders and the channel wall for some selected angular speeds. An immersed boundary method was employed to facilitate implementing the cylinders on a Cartesian grid system. No-slip condition is employed at all solid boundaries including the cylinders, and the flow is assumed to be periodic in the streamwise direction. The presence of the rotating circular cylinders arranged periodically in the streamwise direction causes a significant topological change of the flow, leading to increase of mean friction on the channel walls. More quantitative results as well as qualitative physical explanations are presented to justify the effectiveness of rotating cylinders to modify flow topology, which might be used to enhance heat transfer on the channel walls.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.3
• /
• pp.236-241
• /
• 2008

This paper presents a method to recognize the plane regions for movement of walking robots. When the autonomous agencies using stereo camera or laser scanning sensor is under unknown 3D environment, the mobile agency has to detect the plane regions to decide the moving direction and perform the given tasks. In this paper, we propose a very fast method for plane detection using normal vector of a triangle by 3 vertices defined on a small circular region. To reduce the effect of noises and outliers, the triangle rotates with respect to the center position of the circular region and generates a series of triangles with different normal vectors based on different three points on the boundary of the circular region. The vectors for several triangles are normalized and then median direction of the normal vectors is used to test the planarity of the circular region. The method is very fast and we prove the performance of algorithm for real range data obtained from a stereo camera system.

• Journal of Korea Multimedia Society
• /
• v.22 no.2
• /
• pp.299-310
• /
• 2019

Most web documents are written in Cartesian coordinates, so the study of vertical arrangement of text has been well organized, while the study of circular arrangement is very early. With the recent development of circular display devices, the demand for circular arrangement of texts is increasing. Thus, we proposed a CSS3 extended specification of polar coordinate layout for the circular placement of text. First, we defined the concept of fan model for the text arrangement in polar coordinate which is corresponding to box model in Cartesian coordinate. And, we described new definition on the directions of sentence, paragraph and text orientation in polar coordinate. Based on this new definitions, we developed the extended specification consisting of three parts. A part for setting the fan model, a part for setting directions, and a part for setting typesetting properties. To verify the feasibility of the proposed specification in current web browsers, a preprocessor was developed and sample contents were examined. We compared the code length of the sample contents implemented using other JavaScript library CssWarp.js so as to verify the efficiency of the proposed specification.