• The Transactions of the Korean Institute of Power Electronics
• /
• v.2 no.4
• /
• pp.19-27
• /
• 1997

This paper has described about principle and form of proposed circuit made use of soft switching technology ZVS(Zero Voltage Switching) to reduce turn on and off loss at switching. Also, the analysis of the proposed circuit has described generally by using normalized parameter and operating characteristics have been evaluated as to switching frequency and parameters. Based on the characteristics value, a method of the circuit design is proposed. In addition, this paper proves the propriety of theoretical analysis in terms of the experimental waveforms. In the future, this proposed inverter shows that it can be practically used as power source system for induction cooker etc.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.4
• /
• pp.629-635
• /
• 2017

Free-Flooded Ring (FFR) transducer array for use in Sonar system can be driven with large amplitude in a wide frequency band due to its structural characteristics, in which two resonances of a ring mode (1st radial mode) and an inner cavity vibration mode occur in a low frequency band. Since its sound wave generation characteristics are not influenced by the water pressure, the FFR transducer array is widely used in the deep sea. So FFR has been recognized as a low-frequency active sound source and has received much attention ever since. In order to utilize the FFR transducer array for SONAR systems in military and industrial applications, its equivalent electric circuit model is necessary especially to design the matching circuit between the driving power amplifier and the FFR transducer array. Thus this paper proposes the equivalent electric circuit model of FFR transducer array by using measured values of parameter, and suggest the improved method of parameter identification. Finally it verifies the effectiveness of the proposed circuit model of FFR transducer array by experimental measurements.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.357-360
• /
• 2000

This paper describes a parameter extraction method for HBT(Heterojunction Bipolar Transistor) equivalent circuit model without measurements of special test structures or numerical optimizations. Instead, all equivalent circuit parameters are calculated analytically from small-signal S-parameters measured under different bias conditions. These values being extracted from the cutoff mode can be used to extract intrinsic parameters at the active mode. This method yields a deviation of about 1.3 % between the measured and modeled S-parameters.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.393-396
• /
• 2000

Repeater Duplexer of 800MHz band consists of 4pole transmitter band pass filter, receiver band pass filter and branch circuit. Circuit parameter of Duplexer such as coupled capacitance of equivalent circuit was drawn out and used to coupled line characteristics impedance (Zoo, Zoe) that satisfied resonator condition and attenuation condition. Simulation was carried out by the ADS(Advanced Design System) were obtained good attenuation characteristics (869~894MHz： 65㏈(Min.),824~349MHz： 65㏈(Min.)

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.99.2-99
• /
• 2001

An electronically tunable current-mode second-order multifunctional filter is described in this paper. The proposed filter consists of two four-terminal floating nullors (FTFNs), two dual-output OTAs and two grounded capacitors. The circuit can simultaneously realize the lowpass, bandpass and highpass current transfer functions from the same configuration without changing the circuit configuration and elements. The natural angular frequency we and the parameter wo/Q can be orthogonally controlled through adjusting the transconductance gain of OTA. PSPICE simulation results are employed to confirm the circuit performance.

• Proceedings of the IEEK Conference
• /
• 2001.06a
• /
• pp.413-416
• /
• 2001

In high frequency range, RF circuit design without considering shielding effect can cause several significant changes due to increase in parasitic capacitance and inductance between RF signal lines and shielding box. In this paper, bandpass filter has been made to measure the shielding effect and its s-parameter has been measured by Vector Network Analyzer (VNA). Equivalent circuit model including the shielding effect has been constructed with the lumped elements extracted from the 3D electromagnetic simulator, Maxwell SI. Then, the validity of the model is verified using microwave circuit simulator, ADS (Advanced Design System).

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.10
• /
• pp.1175-1180
• /
• 2014

In this paper, the open ring type DGS(Defected Ground Structure) resonator, applicable to MMIC(Monolithic Microwave Integrated Circuit), is proposed to improve phase noise characteristics of RF oscillator. This resonator is planar type, therefore, it easy to design miniaturrized., and takes relatively high Q value. Modeling the equivalent parameter of resonator is needed, when designing the RF oscillator with resonator. The mathematical method to solve the equivalent parameter of the resonator from the measured results of resonator is introduced in this paper. To verify the method, DGS resonator with 5.8 GHz center frequency is fabricated, for measuring characteristics and calculating the equivalent parameter. The result from this process is compared with the data of the ADS simulation, and as a result both were identical.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1822-1828
• /
• 2008

This paper presents design parameter calculation methodology and its realization to construction for the 10/350${\mu}s$ lightning impulse current generator(ICG) modelled as double exponential function waveform with characteristic parameters ${\alpha},{\beta}$. Matlab internal function, "fzero" was applied to find ${\lambda}={\alpha}/{\beta}$ which is solution of nonlinear equation linearly related with two wave parameter $T_1$ and $T_2$. The calculation results for 10/350${\mu}s$ lightning impulse current show very good accuracy with error less 0.03%. Two type of 10/350${\mu}s$ ICGs based on the calculated design circuit parameters were fabricated by considering the load variation. One is applicable to the MOV based Surge protective device(SPD) for less 15 kA and the other is to test small resistive devices such as spark gap arrester and bonding device with maximum current capability 30 kA. The tested waveforms show error within 10% in comparison with the designed estimation and the waveform tolerance recommended in the IEC 61643-1 and IEC 60060-1.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.4
• /
• pp.64-69
• /
• 2009

This paper addresses the simulation methodology of signal integrity and power integrity for mobile display modules. The proposed technique can be applied to analyse a circuit module which consist of connector, FPCB and driver ICs. The recent demand of serial interconnection technology in the mobile display industry needs delicate impedance control of signal and power traces to prohibit system malfunctioning and to reduce electromagnetic field radiation. Based on the S-parameter and Z-parameter analysis, we analyse the correlation between frequency-domain and time-domain measurements. With multi-port macros, signal integrity can be included in power integrity analysis in time domain.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.1
• /
• pp.36-41
• /
• 2016

The development need of new renewable energy is more and more important to resolve exhaustion of chemical fuels and environmental pollution. Polymer electrolyte membrane fuel cell has been widely studied to the extent that it can be used commercially. But there are many problems to be solved. One of them is to enhance the stability of fuel cell stacks. This paper proposes a new fault diagnosis method using Least Square Method (LSM) which is one of parameter estimation methods. The proposed method extracts equivalent circuit parameters from on-line measurements. Parameters of the circuit are estimated according to normal and abnormal states using simulation. The variation of parameters estimated in each states enables the estimation of state in fuel cells. Thus the LSM presented can be a suitable on-line parameter estimation method in PEMFC.