• Journal of Power Electronics
• /
• v.10 no.3
• /
• pp.219-227
• /
• 2010

Telecom supplies need to conform to low Total Harmonic Distortion (THD) and high Power Factor (PF) as per IEC 61000-3-2 and IEEE 519-1992 standards. These high rating power supplies use a three phase utility in which low THD and high PF are realized via various passive and active wave shaping schemes. In this paper, a new design for three phase telecom power supplies is presented with circuit parameter values optimized for high performance in terms of a low THD, high PF, low ripple and high line and load regulation using a suitable combination of various strategies. The performance of the power supply is validated by extensive simulations.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.32-35
• /
• 2003

Nonlinear parameterization of OLED device from measurements of bias dependence of impedance spectra and parameter extraction using Levenberg-Marquardt complex nonlinear least square regression algorithm based on resistor-capacitor equivalent circuit model enables computer simulation of OLED power driving characteristics in forms of square-wave or sinusoidal output signal at arbitrary conditions. We introduce developed OLED power driving simulation software and discuss transient responses in voltage-or current-controlled operations as well as nonlinear characteristics of OLED, by presenting both the simulation and experimental results. This OLED simulation technique using impedance spectroscopy is extremely useful in predicting performance of the nonlinear device, especially in time-domain analysis of device operation.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.37-39
• /
• 1989

In this paper, the governing equation of each analyzed region of Single-sided Linear Induction Motor was induced from Maxwell's electromagnetic equation. And the linear induction motor was analyzed by finite element method. for calculating inductance, energy perturbation method was applied.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.160-163
• /
• 2000

In this paper, we propose an efficient technique to minimize the input offset of a dynamic latch comparator. We analyzed offset due to charge injection mismatching and unwanted positive feedback during sampling phase. The last one was only considered in the previous works. Based on the analysis, we proposed a modified dynamic latch with initialization switch. The proposed circuit was simulated using 0.65$\mu\textrm{m}$ CMOS process parameter with 5v supply. The simulation results showed that the input offset is less than 5mv at 200㎒ sampling frequency and the input offset is improved about 80% compared with previous work in 5k$\Omega$ input resistance.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.6
• /
• pp.569-575
• /
• 2013

An improved non-quasi-static gate-source impedance model including a parallel RC block for short-channel MOSFETs is developed to simulate RF MOSFET input characteristics accurately in the wide range of high frequency. The non-quasi-static model parameters are accurately determined using the physical input equivalent circuit. This improved model results in much better agreements between the measured and modelled input impedance than a simple one with a non-quasi-static resistance up to 40GHz, verifying its accuracy.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.1 s.14
• /
• pp.5-11
• /
• 2006

One of the most important is to insure that a new circuit design is qualified far release before it is scheduled for manufacturing, test, assembly and delivery. Due to various causes, there happens to be a low yield in the wafer process. Wafer test is a critical process in analyzing the chip characteristics in the EDS(electric die sorting) using analytic tools -wafer map, wafer summary and datalog. In this paper, we propose new analytic map algorithms for DDI chip test data. Using the proposed analytic map algorithms, we expect to improve the yield, quality and analysis time.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1395-1401
• /
• 2010

A paradigm shift in driving system of transportation vehicle from engine to electric motor is required as the problems on air pollution and drain of petroleum resource are on the rize. Moreover while it is possible to control the motor with variable frequency driver, the application of motor in various kinds of vehicles is spread rapidly. In the paper, the effective design method of IPMSM for EV and HEV by using equivalent magnetic circuit and finite element method (FEM) is suggested. First of all, load conditions of the application are calculated. And basic design process of IPMSM is proposed with two design point. Finally, in order to verify the proposed design process, it was compared with the basic design parameter and the FEM analysis results.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.188-192
• /
• 2003

A multilayer two-stage LC bandpass filter using low-temperature cofired-ceramic (LTCC) is proposed in this paper. The proposed bandpass filter is composed of two ceramic substrates with different dielectric constant instead of single ceramic material from top to bottom layer. The bandpass filter size is $2.0 mm{\times}1.2 mm{\times}0.8 mm$. Positioning of attenuation polefrequency, importance parameter for a performance of filter, is discussed using even-odd mode analysis by tuned capacitance of coupling capacitor and those results is implemented to LTCC filter circuit. Measured filter performances show that the insertion losses are -4.5dB, -4.1dB at 2.45GHz, 2.75GHz and the return losses are -8.5dB, 8.7dB.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1882-1884
• /
• 1996

This paper deals with the lightning surge counter. In order to install the effective surge protective devices, it is important to find the parameters of incident surges. For the purpose of observing the occurrence frequency as a parameter of the amplitude of surge, two type surge counters were designed and fabricated. One is operated by surge currents, and the other is operated by surge voltages. The former consists of current sensor, metal oxide varister (MOV), rectifier, capacitor and electromagnetic counter. The latter consists of rectifier, voltage divider, comparator, photo coupler and counter circuit, and is useful for detecting the surge voltages.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.201-204
• /
• 2004

Consider the optimal design for PV system, it is apply to 3kW interconnected electric power PV system, that is a point of reference for 3kW PV the spread residential section system. Through the driving various practical system, we look into that for efficiency of generation and stability of interconnected system. Using obtained data acquisition, It can be suggest that installation and management for system parameter to optimal design maximum generation electric power. PV system have some losses that are variation radiation, shadow, change temperature, unbalanced grid connection, serial circuit loss, MPP deference loss, PCS loss and so forth. Using obtained various performance characteristic result, we can make database in the future, through the this study, we can get the reliance and have regard to spread PV system.