• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.256-273
• /
• 2019

Nowadays interceptors have been widely used in a vast range of high-speed crafts. In this study, the results of interceptor adeptness experiments made in Istanbul Technical University's Towing Tank are unveiled. The model was tested through three transverse locations of interceptors with six different deployment depths. For three locations, the interceptor was positioned transverse on the aft; close to chine, in the middle and close to the keel. The fourth interceptor was a full length of 13.00% LWL. The results show a significant drag reduction in benefits of 1.50%-11.30% for Fn 0.58-1.19 and the trim reduction was observed in between 1.60 and $4.70^{\circ}$. Besides, one of the most significant conclusions indicates that the effect of the interceptor decreases from keel to chine for the same blade deployment heights so the blades should be controlled separately at least in three parts from keel to chine area, if operable.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2001.10a
• /
• pp.40-44
• /
• 2001

선형개발에 대한 연구는 주로 대형선박을 기준으로 Bezier, B-spline 그리고 NURBS와 같은 합성곡선생성기법을 이용하여 일반 곡선기법으로는 표현하기 힘든 구상선수나 굴곡이 심한 선미 등을 표현하고 검증하는 것으로 이루어지고 있다. 하지만, 전체 선박의 70%를 차지하고 있는 중소형 어선의 선형에 대한 연구나 기술적인 보고는 상대적으로 미흡한 실정이다. 본 연구에서는 기존의 라운드타입에서 챠인 및 신챠인타입으로 변화해 가는 중소형 어선의 선형을 NURBS기법을 이용하여 표현하고, 전산화하는 프로그램을 개발하였다.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.11 no.2
• /
• pp.41-44
• /
• 1974

A calculation of the two dimensional added mass moment of inertia for the Kim's chine form sections is made with a special consideration of a location of a axis of rotation. The results are compared with those of Lewis form section equivalent to the above chine form sections calculated by Kumai.

• Journal of Ship and Ocean Technology
• /
• v.2 no.1
• /
• pp.1-12
• /
• 1998

A method to predict the dynamic roll stability of hard-chine planing craft is presented. Starting with the equation of motion, an equation governing small roll perturbations is developed. The roll restoring moment acting on the hull is evaluated by considering “static”and dynamic contributions. The contribution of rudders and skegs, which is significant for this type of craft, is also determined. A worked example is presented to show how the method can be used to find the maximum center of gravity height for transverse stability.

• Textile Coloration and Finishing
• /
• v.8 no.5
• /
• pp.7-16
• /
• 1996

The air-flow dyeing machine is a new type of dyeing machine. Which is an energy saving type to be able to dye the fabrics with the lowest liquor ratio and in shorter time. This machine is operated with an aerodynamic system rather than a hyd raulic system for traditional jet or overflow dyeing. An air-flow dyeing machine(Green-flow) by the use of aerodynamic technology was developed and compared with the Luft-roto machine made by Thies Company, Germany, in this study. Three samples were dyed with both machines under the same dyeing conditions and color fastness, dyeing levelness, drapability, and mechanical properties of these samples were compared. The results were as follows; Both machines have almost the same dyeability. The dyeability was good at liquor ratio of 1: 3.5 and the speed of 450yds/min. The order for drapability was Crepe de Chine > Cool Peach > Charmeuse. Except for the color fastness of sublimation being below class 4, most color fastness of samples dyed with Green-flow m/c were above class 4. The maximum speed was 510yds/min. for Crepe de Chine and the standard deviation of K/S value was lower for Charmeuse and Cool Peach when employed on the "Green-flow" machine and lower for Crepe de Chine when employed on the Luft-roto machine. Comparing with dyeing of the Green-flow machine and that of the Luft-roto machine, the RT of the Charmeuse was found to be higher with the Green-flow machine and thus the sample had an improved wrinkle recovery. LT and WT of Cool Peach were higher, and shear properties(G, 2HG, 2HGS) of Crepe de Chine were higher, both turning out as suitable for clothing. clothing.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.6 no.2
• /
• pp.11-16
• /
• 1969

To grasp the characteristics of hydrodynamic pressure distribution on the hull surface of the chine-type ship in vertical vibration of high frequency the hydrodynamic pressure on the surface of two dimensional cylinders of the curvilinear-element section with chines is investigated in comparison with those of the rectangular section, of the circular section, of the elliptical section, of the triangular section, and of the Lewis form of hypotrocoidal character. The results on the chine-type show markably different characteristics in the pressure distribution from the others.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.6 no.1
• /
• pp.25-34
• /
• 1969

From viewpoints of over-all ship economy the straight framed V-bottom hull forms with chines are considered to be attractive even for usual commercial vessels, because increments of resistance over that of round hull forms, if any, can be well compensated with reduction in construction cost.[1] To investigate the influences of both prismatic coefficient and chine elevation on resistance performance, three models of straight-framed V-bottom hull forms which are similar to Prof. C. Ridgely-Nevitt's W-18, W-8, and W-20[2],[3] in size and hull form coefficients were tested at the SNU Ship Model Towing Tank for resistance measurements. They are of Cp=0.60, 0.65 and 0.70 and of ${\Delta}/(0.01L)^3=300$. Influence of variation of chine elevation on resistance performance were observed with the test results obtained at normal condition, and at the trimed by the stern by 2% and 4% of $L_{bp}$ at normal condition under same displacement. The hull form characteristics are shown in Table 1, and in Fig. 1, 2, 3, 4 and 5. The test results are shown in Fig 8, 9 and 10 in the form of Cr vs. $V/\sqrt{L}$ curves taking Cp as a parameter for normal condition, trim by the stern in 2% and 4% $L_{bp}$ at normal condition , respectively. Cr vs. $V/\sqrt{L}$ curves taking trim condition as a parameter are also shown in Fig 11, 12 and 13 for Cp=0.60 and 0.70, respectively. The best and the worst trim condition at given $V/\sqrt{L}$ in viewpoint of Cr are plotted for each Cp-value as shown in Fig 14, 15 and 16. From the above results the following conclusions are derived: (1) In general, the resistance performance of the straight-framed V-bottom hull forms are not inferior to those of round hull forms. At a certain range of $V/\sqrt{L}$ the former gives less resistance than the latter. (2) Regarding influences of Cp on Cr, it is observed that, at $V/\sqrt{L}$ less than about 0.925, the greater Cp-value gives the more increment of Cr, and that, at $V/\sqrt{L}$ greater than about 0.925 the smaller Cp-value gives the more increment of Cr. It is also noteworthy that the model of Cp=0.70 has remarkable hump on Cr vs. $V/\sqrt{L}$ curve between $V/\sqrt{L}=0.80$ and 0.90. (3) For higher speed within the test range, the chine elevation having the steeper slope around bow and the easier slope around amidship and stern, refered to watering, give the better results in resistance performance. (4) Assuming the chine elevations adopted for the tested models were not of the best, we would expect further improvement of resistance performance for such form. Hence, a systematic study on chine elevation is very disirable to prepare design data of general purpose for the such hull forms.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.14 no.2
• /
• pp.1-9
• /
• 1977

Streamlines around a ship's hull can be calculated by using streamline tracing method replacing the ship section with distribution of singularity. The influence of frame lines on the stream surrounding a hull surface, however, can not be found. Jinnaka studied on streamlines for Lewis form by applying the slender body theory. The influence of frame lines on stream surrounding a hull surface is well found in Jinnaka's method. In this paper streamline calculation method for chine type has been developed by using conformal transformation and applying slender body theory as Jinnaka did. Three kinds of model-one of series 62 for chine type, V.L.C.C. and high speed craft built in Korea for Lewis form-were used for streamline calculation;

• Bulletin of the Society of Naval Architects of Korea
• /
• v.11 no.2
• /
• pp.7-14
• /
• 1974

Hydrodynamic moments produced by the rolling oscillation on the free surface and the associated swaying force were exactly calculated by Ursell-Tasai method for the cylinders with Kim's chine form sections($a_1,\;a_7$). The coefficient of the added moment of inertia $K_{\varphi^{\tau}}$, the progressive wave height ratio $\bar{A}$, the coefficient of swaying forces $K_{RS}$, ${\alpha}_{RS}$ of rolling oscillations are shown in the several figures. The results of the computation were compared with those of lewis form sections. It is concluded that the effect of the section form on the added moment of inertia is significant for the cylinder with the section of same beam-draft ratio and sectional area coefficient, on the other hand, a little effect appears on the wave damping.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.2
• /
• pp.199-209
• /
• 1995

From the results of model tests, statistical regression analysis of EHP estimation based on hull form parameters is adopted in this study. From this result, the method for estimation of EHP at the initial design stage of fishing boats is developed. This method is applied to four standard fishing boats with chine lines and two standard fishing boats with round bottom. The EHP's are estimated and compared to experimental results. In the case of six fishing boats, the estimated EHP corresponds well and approximates well with experimental results through out all the range tested. From these results it can be concluded that this numerical method is very efficient in estimating EHP of fishing boats having chine line and round bottom. Therefore, by applying the proposed method to design of fishing boats, we can improve the resistance characteristics. Further, this method can contribute to reduction of design time and thus down the total expenses.