• 한국전기전자재료학회논문지
• /
• 제24권2호
• /
• pp.152-155
• /
• 2011

Even though nano-scale materials were very advantageous for various applications, there are still problems to be solved such as the stabilization of surface state and realization of low contact resistances between a semiconducting nanowire and electrodes in nano-electronics. It is well known that the effects of contacts barrier between nano-channel and metal electrodes were dominant in carrier transportation in individual nano-electronics. In this report, it was investigated the electrical properties of GaN nanorod devices after chemical etching and rapid thermal annealing for making good contacts. After KOH wet-etching of the contact area the devices showed better electrical performance compared with non-treated GaN individual devices but still didn't have linear voltage-current characteristics. The shape of voltage-current properties of GaN devices were improved remarkably after rapid thermal annealing as showing Ohmic behaviors with further bigger conductivities. Even though chemical etching of the nanorod surfaces could cause scattering of carriers, in here it was shown that the most important and dominant factor in carrier transport of nano-electronics was realization of low contact barrier between nano-channel and metal electrodes surely.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권1호
• /
• pp.108-116
• /
• 2003

In this paper, the experimental results of condensation heat transfer were reported for the plate and shell heat exchangers(P&SHE) using R-l34a. An experimental refrigerant loop has been established to measure the condensation heat transfer coefficient of R-l34a in a vertical P&SHE. Two vertical counter flow channels were formed in the P&SHE by three plates of geometry with a corrugated trapezoid shape of a chevron angle of 45$^{\circ}$. Downflow of the condensing R-l34a in one channel releases heat to the cold up flow of water in the other channel. The effect of the refrigerant mass flux, average heat flux, system pressure and vapor quality of R-l34a on the measured data were explored in detail. The results indicate that at a higher vapor quality the condensation heat transfer coefficients are significantly higher. Condensation heat transfer coefficients were increased when the refrigerant mass flux was increased. A rise in the average heat flux causes an slight increase in the hr. Finally, at a higher system pressure the hr is found to be lower. Correlation is also provided for the measured heat transfer coefficients in terms of the Nusselt number.

• 대한기계학회논문집B
• /
• 제33권10호
• /
• pp.778-782
• /
• 2009

Recently, we developed a simple thermopneumatic micropump having neither a membrane nor a valve. This micropump discharges liquid by a thermopneumatic pressure and refill by a capillary attraction. In case of the micropump driven by the capillary attraction, the flow characteristic depends mainly on the geometry of the micropump. In this paper, we investigated the influence of the geometry of the micropump on the performance of the micropump to illustrate the properness of the micropump shape. We analyzed the micropump characteristics of six types having different geometries by FVM simulation with a commercial CFD tool. Also we fabricated the micropumps with PDMS and glass by micromachining, and tested the performances. The simulation and the test results illustrate that the discharge volume and the discharge time depend on the chamber volume. The expansion angle of the inlet channel location has influence on the refill time, while the front air channel direction has influence on the backward flow loss.

• 대한기계학회논문집A
• /
• 제32권3호
• /
• pp.217-222
• /
• 2008

Equal channel angular pressing (ECAP) is one of the effective methods to produce bulk-nano materials by accumulating plastic strain into the workpiece without changing its cross-sectional shape in the multi-pass processing. However, the forming load becomes higher for manufacturing large specimens using conventional solid or split dies because of friction, flash formation, and usage of dummy specimen. In the present investigation, better split die was designed to reduce the forming loads and improve the geometrical accuracy of the specimen in the multi-pass ECAP. The new die exit channel was also designed to reduce the friction effect. Experiments with AA1050 specimens with a square cross-section were carried out to examine the design goal using the proposed split dies for routes A and C up to four passes. The numerical forming simulations were used to determine the effective geometry of various die models in the present work.

• 한국지역지리학회지
• /
• 제17권2호
• /
• pp.141-149
• /
• 2011

사자평 고산습지는 유역분지 및 기반암의 특성과 화전의 영향을 받아 형성되었다. 사자평 유역분지는 출구가 좁고, 기반양은 많은 암설을 생산하여 사면 아래로 공급한다. 그리고 화전을 위하여 삼림을 제거함으로써 표토의 세립물질이 사전천의 하상에 퇴적되어, 시전천의 유로 주변에 고산습지가 형성되었다 사자평의 습원에는 도로를 따라 우곡이 형성되었는데, 우곡은 습원으로 공급되는 사력물질과 통류의 공급을 차단함으로써 습원을 건조화 시킨다. 이를 방지하기 위해서는 배수로의 수위를 기반암 풍화층의 높이까지 높여 습원으로 통류가흐를 수 있도록 하여야 하며, 배수로의 모양을 자연스러운 불규칙한 형태로 조정하여야 하고 시전천의 하상에 인위적인 방해물을 적치하여 시전천의 하상이 낮아지는 것을 방지하여야 한다.

• 한국콘텐츠학회논문지
• /
• 제9권11호
• /
• pp.225-230
• /
• 2009

영상처리 분야에서 필터링은 특정 목적에 따른 영상의 화질 개선을 위해 사용되고 있으며, 자기공명영상 분야에서도 여러 가지 필터들이 영상의 질적 향상을 위해 사용되고 있다. 본 논문에서는 최근 연구되어진 변형된 Fermi-Direc 필터를 여러 가지 형태로 다시 변형해 보고 가장 최적화된 형태를 도출해 보았다. 또한 이렇게 제작된 필터를 현재 병원에서 사용되고 있는 MR장비로 환자를 통해서 얻어진 임상 영상(original image)에 적용하였다. 그 결과 임상 영상(original image)들이 필터를 통과한 후 육안으로 보았을 때 화질이 개선되어진 것을 알 수 있었으며, 이들의 정량적인 평가를 위해 각 영상들의 R, G. B 채널의 히스토그램을 구하였다. 결론적으로, 질환에 따른 차이는 다소 있었으나 original image에 비해 필터를 적용한 후 얻어진 영상의 명암비와 선명도가 더 우수한 결과를 보였다. 따라서 변형된 Fermi-Filter의 사용이 실제 환자의 질병을 정확히 진단하여 치료하는데 기여할 수 있음을 알 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제17권12호
• /
• pp.1301-1307
• /
• 2004

Reduced pressure chemical vapor deposition(RPCYD) technology has been investigated for the growth of SiGe epitaxial films with two dimensional in-situ doped boron impurities. The two dimensional $\delta$-doped impurities can supply high mobility carriers into the channel of SiGe heterostructure MOSFETs(HMOS). Process parameters including substrate temperature, flow rate of dopant gas, and structure of epitaxial layers presented significant influence on the shape of two dimensional dopant distribution. Weak bonds of germanium hydrides could promote high incorporation efficiency of boron atoms on film surface. Meanwhile the negligible diffusion coefficient in SiGe prohibits the dispersion of boron atoms: that is, very sharp, well defined two-dimensional doping could be obtained within a few atomic layers. Peak concentration and full-width-at-half-maximum of boron profiles in SiGe could be achieved in the range of 10$^{18}$ -10$^{20}$ cm$^{-3}$ and below 5 nm, respectively. These experimental results suggest that the present method is particularly suitable for HMOS devices requiring a high-precision channel for superior performance in terms of operation speed and noise levels to the present conventional CMOS technology.

• 대한기계학회논문집B
• /
• 제25권6호
• /
• pp.860-867
• /
• 2001

In this study, condensation heat transfer experiments were conducted with plate and shell heat exchangers(P&SHE) using R-22. An experimental refrigerant loop has been established to measure the condensation heat transfer coefficient of R-22 in a vertical P&SHE. Two vertical counter flow channels were formed in the P&SHE by three plates of geometry with a corrugated trapezoid shape of a chevron angle of 45°. Downflow of the condensing R-22 in one channel releases heat to the cold upflow of water in the other channel. The effect of the refrigerant mass flux, average heat flux, system pressure and vapor quality of R-22 on the measured data were explored in detail. The results indicate that at a higher vapor quality the condensation heat transfer coefficients are significantly higher. A rise in the refrigerant mass flux causes an increase in the h(sub)r. Also, a rise in the average heat flux causes an increase in the h(sub)r. Finally, at a higher system pressure the h(sub)r is found to be slightly lower. Correlation is also provided for the measured heat transfer coefficients in terms of the Nusselt number.

• 수산해양기술연구
• /
• 제40권4호
• /
• pp.304-310
• /
• 2004

본 연구에서는 10톤급(9.77 G/T) 소형 연안어선의 저항성능을 회류수조를 이용한 모형시험을 통하여 조사하고, 저항성능개선을 위한 선형특성과 초기 트림에 대한 영향을 검토하였다. 본 연구를 통하여 다음과 같은 몇가지 결론을 도출할 수 있다. (1) 선미 A.P. 이후 돌출부 길이를 키우는 것은, 트림이 억제되면서 선수부 쇄파 현상이 커질 수 있으나, 선미단에서 빠져나가는 유체의 흐름을 개선시켜 저항성능을 크게 향상시킬 수 있다. (2) 적절한 초기 트림을 줌으로써 저항성능이 크게 개선될 수 있다. (3) 선수부 유체흐름을 개선시키기 위해 챠인의 폭을 줄인 선형보다는 이 폭을 그대로 유지하는 것이 파가 선체의 선측을 타고 올라가는 것을 방지하고 트림을 키워 성능측면에서 유리하게 작용한다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제7권4호
• /
• pp.254-259
• /
• 2007

In this report, several fabrication techniques for the formation of various nanochannels (with $SiO_2$, Si, or Quartz) are introduced. Moreover, simple fabrication technique for generating $SiO_2$ nanochannels without nanolithography is presented. By using different nanochannels, the degree of stretching DNA molecule will be evaluated. Finally, we introduce a nanometer scale fluidic channel with electrodes on the sidewall of it, to detect and analyze single DNA molecule. The cross sectional shape of the nanotrench is V-groove, which was implemented by thermal oxidation. Electrodes were deposited through both sidewalls of nanotrench and the sealing of channel was done by covering thin poly-dimethiysiloxane (PDMS) polymer sheet.